Moto g30 Service and Repair Manual V1.0

Moto g30
Lenovo Moto g30
Level 2 – Service and Repair Manual
Lenovo Moto g30
Level 2 – Service and Repair Manual
REVISION HISTORY
Revision
1
PAGE 2
Date
Notes
01/25/2021
Initial Release.
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
TABLE OF CONTENTS
Revision History.................................................................................................................................. 2
List of Tables ....................................................................................................................................... 7
Table of Figures .................................................................................................................................. 7
Safety Information .............................................................................................................................. 8
Cautions and Warnings ....................................................................................................................... 8
Battery Safety Guidelines.................................................................................................................... 8
Introduction ......................................................................................................................................... 9
External Views..................................................................................................................................... 9
Main Exploded Views ........................................................................................................................ 11
Disassembly and Recovery ............................................................................................................. 14
Disassembly and Recovery Map....................................................................................................... 14
Tools Required for Disassembly ....................................................................................................... 15
SIM Tray Removal ............................................................................................................................ 17
Water Detection Label Inspection ..................................................................................................... 18
IMEI Label Removal .......................................................................................................................... 19
Battery Cover Removal ..................................................................................................................... 20
Side key Waterproof Film 1 Removal ............................................................................................... 23
Side key Waterproof Film 2 Removal ............................................................................................... 24
Top Bracket Waterproof Film Removal ............................................................................................. 25
Secondary MIC Foam Removal ........................................................................................................ 26
Top Bracket Removal........................................................................................................................ 27
Water Detection Label Inspection ..................................................................................................... 28
Speaker Box Waterproof Film Removal............................................................................................ 29
Primary MIC Foam Removal ............................................................................................................. 30
Speaker Dust Net Foam Removal .................................................................................................... 31
Speaker Box Removal ...................................................................................................................... 32
Water Detection Label Inspection ..................................................................................................... 33
Fingerprint Sensor Flex Removal...................................................................................................... 34
Front-Facing Camera Copper Foil Removal ..................................................................................... 35
Front-Facing Camera Removal ......................................................................................................... 36
Front-Facing Camera Grommet Removal......................................................................................... 37
2M Macro Rear-Facing Camera Removal ........................................................................................ 38
2M Depth Rear-Facing Camera Removal......................................................................................... 39
2M Macro Rear-Facing Camera Copper Foil Removal..................................................................... 40
2M Depth Rear-Facing Camera Conductive Cloth Removal ............................................................ 41
Main PCB Removal ........................................................................................................................... 42
Water Detection Label Inspection ..................................................................................................... 44
PAGE 3
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
64M Rear-Facing Camera Removal ................................................................................................. 45
8M Rear-Facing Camera Removal ................................................................................................... 46
Audio Jack Grommet Removal ......................................................................................................... 47
RF Heat Spreader Removal .............................................................................................................. 48
BB Heat Spreader Removal .............................................................................................................. 49
Receiver Removal ............................................................................................................................. 50
Receiver Insulated Tape Removal .................................................................................................... 51
Sub Board Removal .......................................................................................................................... 52
USB Grommet Removal.................................................................................................................... 54
Vibrator Removal .............................................................................................................................. 55
Battery Removal ................................................................................................................................ 56
Coax Cable Removal ........................................................................................................................ 58
Side Key FPC Removal .................................................................................................................... 59
Proximity Sensor Grommet Removal ................................................................................................ 60
Silicone Light Guide Removal ........................................................................................................... 61
RF Thermal Silica Removal .............................................................................................................. 62
Power Thermal Silica Removal ......................................................................................................... 63
LCD FPC Foam Removal ................................................................................................................. 64
Fingerprint Sensor Conductive Sponge Removal ............................................................................. 65
Rear-Facing Camera Lens Removal ................................................................................................ 66
Flash Lens Removal ......................................................................................................................... 67
Flash Lens Foam Removal ............................................................................................................... 68
Parts Refresh..................................................................................................................................... 69
Tools Required for Parts Refresh ..................................................................................................... 69
Battery Cover Cleaning ..................................................................................................................... 70
Front Housing Cleaning .................................................................................................................... 71
Top Bracket Cleaning........................................................................................................................ 72
Assembly ........................................................................................................................................... 73
Assembly Map ................................................................................................................................... 73
Tools Required for Assembly ............................................................................................................ 74
Power Thermal Silica Assembly........................................................................................................ 75
RF Thermal Silica Assembly ............................................................................................................. 76
Water Detection Label Assembly ...................................................................................................... 77
Vibrator Assembly ............................................................................................................................. 78
Silicone Light Guide Assembly.......................................................................................................... 79
Proximity Sensor Grommet Assembly .............................................................................................. 80
Receiver Sealed Foam Assembly ..................................................................................................... 81
Receiver Insulated Tape Assembly .................................................................................................. 82
Receiver Assembly ........................................................................................................................... 83
PAGE 4
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Water Detection Label Assembly ...................................................................................................... 84
BB Heat Spreader Assembly ............................................................................................................ 85
RF Heat Spreader Assembly ............................................................................................................ 86
8M Rear-Facing Camera Assembly .................................................................................................. 87
64M Rear-Facing Camera Assembly ................................................................................................ 88
Audio Jack Grommet Assembly ........................................................................................................ 89
Main PCB Assembly ......................................................................................................................... 90
2M Depth Rear-Facing Camera Conductive Cloth Assembly........................................................... 91
2M Macro Rear-Facing Camera Copper Foil Assembly ................................................................... 92
2M Macro Rear-Facing Camera Assembly ....................................................................................... 93
2M Depth Rear-Facing Camera Assembly ....................................................................................... 94
Front-Facing Camera Grommet Assembly ....................................................................................... 95
Front-Facing Camera Assembly ....................................................................................................... 96
Front-Facing Camera Copper Foil Assembly.................................................................................... 97
Side Key FPC Assembly ................................................................................................................... 98
LCD FPC Foam Assembly .............................................................................................................. 100
Water Detection Label Assembly .................................................................................................... 101
USB Grommet Assembly ................................................................................................................ 102
Sub Board Assembly ....................................................................................................................... 103
Coax Cable Assembly ..................................................................................................................... 104
Battery Adhesive Assembly ............................................................................................................ 105
Battery Assembly ............................................................................................................................ 106
FPS Flex Assembly ......................................................................................................................... 108
Flash Lens Foam Assembly ............................................................................................................ 109
Flash Lens Adhesive Assembly ...................................................................................................... 110
Flash Lens Assembly ...................................................................................................................... 111
Rear-Facing Camera Lens Adhesive Assembly ............................................................................. 112
Rear-Facing Camera Lens Assembly ............................................................................................. 113
Top Bracket Assembly .................................................................................................................... 114
FPS Adhesive Assembly ................................................................................................................. 115
FPS Conductive Sponge Assembly ................................................................................................ 116
Speaker Box Assembly ................................................................................................................... 117
Side Key Waterproof Film 1 Assembly ........................................................................................... 118
Side Key Waterproof Film 2 Assembly ........................................................................................... 119
Secondary MIC Foam Assembly..................................................................................................... 120
Top Bracket Waterproof Film Assembly ......................................................................................... 121
Primary MIC Foam Assembly ......................................................................................................... 122
Speaker Dust Net Assembly ........................................................................................................... 123
Speaker Box Waterproof Film Assembly ........................................................................................ 124
PAGE 5
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Rear-Facing Camera Decoration Adhesive Assembly.................................................................... 125
FPS Sealed Foam Adhesive Assembly .......................................................................................... 126
Battery Cover Assembly.................................................................................................................. 127
IMEI Label Assembly ...................................................................................................................... 128
Sim Tray Assembly ......................................................................................................................... 129
Assembly Quality check ................................................................................................................ 130
Battery Quality Check ..................................................................................................................... 130
Grommet and Connectors Quality Check ....................................................................................... 131
Screws Graphite Quality Check ...................................................................................................... 132
PAGE 6
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
LIST OF TABLES
Table 1. External Views Parts List ...................................................................................................... 10
Table 2. Assembly Exploded View Parts List ..................................................................................... 11
TABLE OF FIGURES
Figure 1. External Views ....................................................................................................................... 9
9BFigure 2. Assembly Exploded View .................................................................................................... 11
PAGE 7
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
SAFETY INFORMATION
Cautions and Warnings
Electrostatic Discharge
The phone components may be damaged by electrostatic discharge (ESD). Always use an ESD mat and ground strap
when working with internal components.
Battery Safety Guidelines
Handle Battery with care. Ensure Battery edges and surfaces are not dented or deformed. If the Battery Pack is dropped
to the floor, it may be internally damaged and must be scrapped.
Ensure all surfaces, fixtures, and phone components contacting the Battery are smooth and clean.
Ensure Battery and its insulation are not damaged (e.g. scratched, dented, punctured) prior to and throughout assembly.
Prior to assembly, ensure Battery edges and surfaces are not dented or deformed, and that fixtures and parts that will
contact the Battery are free of foreign material.
Ensure screws and screwdrivers do not contact the Battery.
Failure to adhere to Safety Critical Note(s) may increase risk of rupture, burning, or failure to function safely when used
by the customer.
PAGE 8
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
INTRODUCTION
External Views
Figure 1. External Views
PAGE 9
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Table 1. External Views Parts List
Reference #
Description
1
Receiver Mesh
2
Google Key
3
Volume Key
4
Power Key
5
Camera Lens
6
Camera Deco
7
Flash Lens
8
FPS
9
Speaker Mesh
10
USB Port
11
MIC
12
Main Lens
13
Sim Door
14
Front-Housing
15
Battery Cover
PAGE 10
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Main Exploded Views
Figure 2. Assembly Exploded View
9B
Table 2. Assembly Exploded View Parts List
Reference #
Description
Recovery Part
1
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
Yes
2
TNM716-BVU000-001+Silicone sleeve/DX
Yes
3
TNM716-BVJ000-003+Thermal silica_LD
No
4
MDL,CAMR,13M,front;C0DF03;Kunshan,FF:Cap
Yes
5
TNM716-BVJ000-004+RF Thermal silica_LD
No
6
TNM719-BVJ001-002+CAM ground copper foil
No
7
TNN502-BQF000-010+Receive_DS
Yes
8
TNM701-BVJ002-004+earpiece insulating gl
No
9
TNEI06-320817-000+RF COA LIN 119.5_0.81
Yes
10
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
Yes
11
TNM716-BVJ000-005+EAR silicone sleeve_DX
Yes
12
TNM709-BVJ001-023+flash cover seal Foam_
No
13
TNM223-BVJ000-000+Flash COV_TRA_rear/HG
Yes
14
TNM715-BVJ001-007+flash cover Adhesive_A
No
PAGE 11
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Reference #
Description
Recovery Part
15
XT2129-1 Up frame_PB&S101-BVU135-200CS
XT2129-1 UP Frame_PS&S101-BVU055-200CS
XT2129-2 UP Frame_PB&S101-BVU136-200CS
XT2129-2 UP Frame_PS&S101-BVU056-200CS
Yes
16
TNM701-BVJ001-000+Waterproof membrane/AP
No
17
FINGERPRT SCANNER,Phantom Black,FPC1520
FINGERPRT SCANNER,Pastel sky,FPC1520
FINGERPRT SCANNER,Phantom Black,FPC1520,
FINGERPRT SCANNER,Pastel Sky,FPC1520,no
Yes
18
TNM701-BVJ002-006+LCMSide WaterproofFilm
No
19
TNEI30-BVJ130-000+sim card tray_black_JH
TNEI30-BVJ131-000+sim card tray_black_JH
TNEI30-BVJ050-000+sim card tray_white_JH
TNEI30-BVJ051-000+sim CAR TRA_PAS WHI_JH
Yes
20
TNM205-BVU130-000+rear lens/black/DT
TNM205-BVU050-000+rear lens/white/DT
Yes
21
TNM715-BVJ001-000+Camera Lens Adhesive
No
22
XT2129-1 Batt Cover_PB&S101-BVU137-300CS
XT2129-1 Batt Cover_PS&S101-BVU057-300CS
Capri+ etching_BR_PB&S101-BVU13B-300CS
Capri+ etching_BR_PS&S101-BVU05B-300CS
XT2129-2 Batt Cover_PB&S101-BVU138-300CS
XT2129-2 Batt Cover_PS&S101-BVU058-300CS
XT2129-3 Batt Cover_PB&S101-BVU139-300CS
XT2129-3 Batt Cover_PS&S101-BVU059-300CS
Capri+ etching_LA_PB&S101-BVU13A-300CS
Capri+ etching_LA_PS&S101-BVU05A-300CS
Capri+ etching_EU_PB&S101-BVU13C-300CS
Capri+ etching_EU_PS&S101-BVU05C-300CS
Capri+ etching_UK_PB&S101-BVU13I-300CS
Capri+ etching_UK_PS&S101-BVU05I-300CS
Capri+ etching_APEM_PB&S101-BVU13E-300CS
Capri+ etching_APEM_PS&S101-BVU05E-300CS
XT2129-3 etching_PB&S101-BVU13G-300CS
XT2129-3 etching_PS&S101-BVU05G-300CS
23
MDL,CAMR,8M,rear,;C08F31;Q Tech,AF:capri
Yes
24
MDL,CAMR,64M,after,;L64BA10;O-FILM,AF:Ki
Yes
25
MDL,CAMR,2M,rear,;L02BF40;O-FILM:Capri/C
Yes
26
TNN703-BVJ003-020+2M Camera Module LH
Yes
27
TNM715-BVJ002-009+conductive adhesive
No
28
TNM715-BVJ002-014+Posterior adhesive_APL
No
29
TNM701-BVJ001-002+Waterproof membrane/AP
No
30
TNN802-BVJ000-000+SIDEKEY_FPC FIN part_Z
No
PAGE 12
Yes
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Reference #
Description
Recovery Part
31
ACCY,BAT,5000mAh,ACCY,BAT,5000mAh,JK50,L
No
32
XT2129 Speaker Box&S108-BVU000-000CS
Yes
34
XT2129-1 Sub Baord&S102-BVU000-000CS
XT2129-2 Sub Board&S102-BVU000-001CS
ASSY,DTR BRD,Capri Plus BR
Yes
37
TNM716-BVJ000-007+T-C silicone sleeve_DX
Yes
38
TNM715-BVJ001-001+Battery Adhesive_AP
No
39
TNN901-BVU000-000+Flat motor_JX
No
40
TNM701-BVJ001-001+Waterproof membrane/AP
No
41
TNM711-BVJ001-000+Speaker dust net_AP
No
42
TNM709-BVJ001-011+MIC dust net Foam_AP
No
-
TNM501-211103-011+round head screw
No
-
TNM501-211102-020+round head screw
No
-
TNM501-211105-006+round head screw_LJT
No
-
TNM716-BVJ000-010+LED silicone sleeve_DX
Yes
-
TNP316-096000-100+Water label
No
-
TNM716-BVJ000-009+P-S silicone sleeve_DX
Yes
-
TNM709-BVJ000-001+FP Conductive sponge1
No
-
TNM709-BVJ003-026+LCD FPC foam_APLT
No
-
TNM715-BVJ001-004+decoration Adhesive_AP
No
-
TNM715-BVJ001-005+FP seal adhesive_AP
No
-
TNM715-BVJ001-008+FPS adhesive_AP
No
-
TNM721-BVU001-001+Graphite Sheet/LS
No
-
TNM721-BVU000-002+Graphite Sheet/SQ
No
PAGE 13
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
DISASSEMBLY AND RECOVERY
Disassembly and Recovery Map
*Shaded parts may be eligible for parts recovery.
IMEI Label
Sim Tray
Water
Detection
Label
Primary
MIC Foam
Speaker
Dust Net
Foam
Top Bracket
Waterproof
Film
Secondary
MIC Foam
Power
Thermal
Silica
RF
Thermal
Silica
Sidekey
Waterproof
Film1
Sidekey
Waterproof
Film2
Sidekey
FPC
Coax
Cable
Receiver
Insulated Tap
Silicone
Light Guide
Rear-Facing
Camera
Lens
Receiver
P-sensor
Grommet
Water
Detection
Top
Bracket
Label
Vibrator
FPS
Conductive
Sponge
Flash Lens
Foam
Battery
Water
Receiver
Detection
Sealed
Foam
Label
Battery
Cover
LCD FPC
Foam
Front
Housing
RF
Heat
Spreader
Rear-Facing
Camera
Conductive
Copper Foil
BB
Heat
Spreader
Rear-Facing
Camera
Rear-Facing
Camera
Conductive
Cloth
Front-Facing
Camera
Grommet
Water
Detection
Label
Front-Facing
Camera
Copper Foil
Front-Facing
Camera
Audio
Jack
Grommet
Main PCB
Speaker Box
Waterproof
Film
USB
Grommet
Sub Board
Water
Detection
Label
Speaker Box
PAGE 14
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Tools Required for Disassembly
The following tools are required to disassemble the Moto g30 phone.
Description
Part #
Thin Plastic Spudger
0-00-00-40826
SIM/SD Tray Removal Tool
--
Hot Plate
--
Black Stick
--
Torque Driver
--
Shim
4-00-5L-10000
PAGE 15
Picture/Drawing
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Description
Part #
PH00 Bit
--
Plastic Tweezers
--
--
ESD Mat
--
--
Wrist Strap
--
--
Gloves
--
--
PAGE 16
Picture/Drawing
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
SIM Tray Removal
NOTE
The SIM Tray can be recovered and
reused after removal.
1.
Power off the device before beginning with the
procedure. Use the SIM Tray Removal pin to
push into the SIM Tray hole.
2.
Press the SIM Tray removal tool to make it popout as shown.
3.
Use fingers to take out the SIM Tray.
PAGE 17
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Water Detection Label Inspection
NOTE
If the Water Detection Label (WDL) has been
activated, the phone’s warranty no longer applies.
Inspect the WDL inside the SIM Tray Slot for signs of
activation. Use external light if needed.
PAGE 18
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
IMEI Label Removal
NOTE
Remove the IMEI Label only if
necessary. After you remove it, you
cannot reuse it.
Use the Plastic Tweezer to remove the IMEI Label
from the SIM tray.
PAGE 19
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Battery Cover Removal
NOTE
The Battery Cover can be recovered
and reused after removal if it is
undamaged.
1.
Use the Shim to create a gap between the
Battery Cover and the Front-Housing.
NOTE
Make sure to start at the Side Key position as
shown.
2.
Use the Shim to create a gap between the
Battery Cover and the Front-Housing.
3.
Use the Shim to create a gap between the
Battery Cover and the Front-Housing.
PAGE 20
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
4.
Use the Shim to create a gap between the
Battery Cover and the Front-Housing.
5.
Use the Shim in the direction as shown.
NOTE
Care not to slide the Shim to avoid damaging the
Front-Housing.
NOTE
Care while removing the Battery Cover with Shim
do not scratch the Battery Cover and Front rim.
NOTE
Care need strong force to pull and disengage the
area around Camera Lens from the FrontHousing since it has adhesive.
6.
Use fingers to push out the Fingerprint Sensor
from the location as shown.
/// WARNING ///
Use care not to disconnect the Fingerprint
Sensor (FPS) Flex from the Battery Cover when
removing the Front Housing.
PAGE 21
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
7.
PAGE 22
Split the Battery Cover from the Front-Housing
as shown.
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Side key Waterproof Film 1 Removal
NOTE
After you remove the Side key
Waterproof Film 1, you cannot reuse it.
Use the Plastic Tweezer to remove the Side key
Waterproof Film 1 from the location as shown.
PAGE 23
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Side key Waterproof Film 2 Removal
NOTE
After you remove the Side key
Waterproof Film 2, you cannot reuse it.
Use the Plastic Tweezer to remove the Side key
Waterproof Film 2 from the location as shown.
PAGE 24
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Top Bracket Waterproof Film Removal
NOTE
After you remove the Top Bracket
Waterproof Film, you cannot reuse it.
Use the Plastic Tweezer to remove the Top Bracket
Waterproof Film from the location as shown.
PAGE 25
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Secondary MIC Foam Removal
NOTE
After you remove the Secondary MIC
Foam, you cannot reuse it.
Use the Plastic Tweezer to remove the Secondary
MIC Foam from the location as shown.
PAGE 26
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Top Bracket Removal
NOTE
The Top Bracket can be recovered and
reused after removal.
1.
Use the flat end of the Black Stick to disengage
the FPS from the Top Bracket as shown since it
has back adhesive.
2.
Use the Torque Driver with PH00 Bit to remove
the nine white screws as shown.
/// WARNING ///
The screws cannot be reused after removal.
3.
PAGE 27
Use the flat end of the Black Stick to lift the Top
Bracket from the location as shown.
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Water Detection Label Inspection
NOTE
If the Water Detection Label (WDL) has been
activated, the phone’s warranty no longer applies.
Inspect the WDL, which is visible on the Main PCB.
Examine it for signs of activation.
PAGE 28
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Speaker Box Waterproof Film Removal
NOTE
After you remove the Speaker Box
Waterproof Film, you cannot reuse it.
Use the Plastic Tweezer to remove the Speaker Box
Waterproof Film from the location as shown.
PAGE 29
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Primary MIC Foam Removal
NOTE
After you remove the Primary MIC
Foam, you cannot reuse it.
Use the Plastic Tweezer to remove the Primary MIC
Foam from the location as shown.
PAGE 30
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Speaker Dust Net Foam Removal
NOTE
After you remove the Speaker Dust Net
Foam, you cannot reuse it.
Use the Plastic Tweezer to remove the Speaker
Dust Net Foam from the location as shown.
PAGE 31
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Speaker Box Removal
NOTE
The Speaker Box can be recovered
and reused after removal.
1.
Use the Torque Driver with PH00 Bit to remove
the seven screws as shown.
/// WARNING ///
The screws cannot be reused after removal.
2.
PAGE 32
Use the flat end of the Black Stick to lift the
Speaker Box as shown.
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Water Detection Label Inspection
NOTE
If the Water Detection Label (WDL) has been
activated, the phone’s warranty no longer applies.
Inspect the WDL, which is visible on the Sub Board.
Examine it for signs of activation.
PAGE 33
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Fingerprint Sensor Flex Removal
NOTE
The Fingerprint Sensor Flex can be
recovered and reused after removal.
Use the BtB tool to remove the Fingerprint Sensor
Flex from the location as shown.
PAGE 34
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Front-Facing Camera Copper Foil Removal
NOTE
After you remove the Front-Facing
Camera Copper Foil, you cannot reuse it.
Use the Plastic Tweezer to remove the Front-Facing
Camera Copper Foil from the location as shown.
PAGE 35
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Front-Facing Camera Removal
NOTE
The Front-Facing Camera can be
recovered and reused after removal.
Use the BtB tool to remove the Front-Facing
Camera from the Main PCB as shown.
PAGE 36
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Front-Facing Camera Grommet Removal
NOTE
The Front-Facing Camera Grommet
can be recovered and reused after
removal.
Use the Plastic Tweezer to remove the Front-Facing
Camera Grommet from the location as shown.
PAGE 37
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2M Macro Rear-Facing Camera Removal
NOTE
The 2M Macro Rear-Facing Camera
can be recovered and reused after
removal.
1.
Use the BtB tool to disengage the 2M Macro
Rear-Facing Camera Flex from the location as
shown.
2.
Use the Plastic Tweezer to remove the 2M
Macro Rear-Facing Camera from the location
as shown.
PAGE 38
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2M Depth Rear-Facing Camera Removal
NOTE
The 2M Depth Rear-Facing Camera
can be recovered and reused after
removal.
1.
Use the BtB tool to disengage the 2M Depth
Rear-Facing Camera Flex from the location as
shown.
2.
Use the Plastic Tweezer to remove the 2M
Depth Rear-Facing Camera from the location as
shown.
PAGE 39
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2M Macro Rear-Facing Camera Copper Foil Removal
NOTE
After you remove the 2M Macro RearFacing Camera Copper Foil, you cannot
reuse it.
Use the Plastic Tweezer to remove the 2M Macro RearFacing Camera Copper Foil from the location as
shown.
PAGE 40
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2M Depth Rear-Facing Camera Conductive Cloth Removal
NOTE
After you remove the 2M Depth RearFacing Camera Conductive Cloth, you
cannot reuse it.
Use the Plastic Tweezer to remove the 2M Depth
Rear-Facing Camera Conductive Cloth from the
location as shown.
PAGE 41
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Main PCB Removal
NOTE
The Main PCB can be recovered and
reused after removal.
1.
Use the Plastic Tweezer to remove the Coax
Cable from the location as shown.
2.
Use the BtB tool to disengage Battery Flex BtB
Connector from the location as shown.
3.
Use the BtB tool to disengage Display Flex BtB
Connector from the location as shown.
PAGE 42
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
4.
Use the flat end of the Black Stick to disengage
the Side Key Flex from the location as shown.
5.
Use the Plastic Tweezer to remove the Side
Key from the location as shown.
6.
Use the Torque Driver with PH00 Bit to remove
the two screws as shown.
/// WARNING ///
The screw cannot be reused after removal.
7.
PAGE 43
Use the pointed end of the Black Stick to lift the
Main PCB from the location as shown.
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Water Detection Label Inspection
NOTE
If the Water Detection Label (WDL) has been
activated, the phone’s warranty no longer applies.
Inspect the WDL, which is visible on the FrontHousing. Examine it for signs of activation.
PAGE 44
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
64M Rear-Facing Camera Removal
NOTE
The 64M Rear-Facing Camera can be
recovered and reused after removal.
Use the BtB tool to remove the 64M Rear-Facing
Camera from the location as shown.
PAGE 45
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
8M Rear-Facing Camera Removal
NOTE
The 8M Rear-Facing Camera can be
recovered and reused after removal.
Use the BtB tool to remove the 8M Rear-Facing
Camera from the location as shown.
PAGE 46
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Audio Jack Grommet Removal
NOTE
The Audio Jack Grommet can be
recovered and reused after removal.
Use the Plastic Tweezer to remove the Audio Jack
Grommet from the location as shown.
PAGE 47
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
RF Heat Spreader Removal
NOTE
After you remove the RF Heat Spreader,
you cannot reuse it.
Use the Plastic Tweezer to remove the RF Heat
Spreader from the location as shown.
PAGE 48
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
BB Heat Spreader Removal
NOTE
After you remove the BB Heat Spreader,
you cannot reuse it.
Use the Plastic Tweezer to remove the BB Heat
Spreader from the location as shown.
PAGE 49
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Receiver Removal
NOTE
The Receiver can be recovered and
reused after removal.
1.
Use the flat end of the Black Stick to lift the
Receiver from the location as shown.
2.
Remove the Receiver from the phone.
PAGE 50
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Receiver Insulated Tape Removal
NOTE
After you remove the Receiver Insulated
Tape, you cannot reuse it.
Use the Plastic Tweezer to remove the Receiver
Insulated Tape from the location as shown.
PAGE 51
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Sub Board Removal
NOTE
The Sub Board can be recovered and
reused after removal.
1.
Use the Plastic Tweezer to remove the Coax
Cable from the location as shown.
2.
Use the BtB tool to carefully disengage the LCM
BtB Connector from the location on the Sub
Board as shown.
3.
Use the Torque Driver with PH00 Bit to remove
the screw as shown.
/// WARNING ///
The screw cannot be reused after removal.
PAGE 52
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
4.
PAGE 53
Use the flat end of the Black Stick to gently lift
the Sub Board from the location as shown.
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
USB Grommet Removal
NOTE
The USB Grommet can be recovered
and reused after removal.
Use the Plastic Tweezer to remove the USB Grommet
from the location as shown.
PAGE 54
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Vibrator Removal
NOTE
Remove the Vibrator only if necessary.
After you remove it, you cannot reuse it.
Use the pointed end of the Black Stick to gently
disengage the Vibrator from the location as
shown.
PAGE 55
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Battery Removal
/// WARNING ///
// CAUTION //
Failure to adhere to Safety Critical Note(s) may
increase risk of rupture, burning, or failure to
function safely when used by the customer.
Refer to the Battery Safety Guidelines.
Handle the Battery Pack with care. If dropped on the
floor, it may be internally damaged and must be
scrapped.
NOTE
Remove the Battery only if it is
defective or damaged. After you
remove it, you cannot reuse it.
1.
Ensure Battery and its insulation are not damaged (e.g.
scratched, dented, punctured) prior to and through
assembly.
Prior to assembly, ensure Battery edges and surfaces
are not dented or deformed, and that fixtures and parts
that will contact the Battery are free of foreign material.
Ensure screws and screwdrivers do not contact the
Battery.
Set the temperature of the Hot Plate to 80°C
(176°F).
// CAUTION //
Do not set the Hot Plate temperature higher than
80°C (176°F). Damage to the phone may occur.
NOTE
Preheating with an oven is also acceptable if the
oven is set to the same temperature.
2.
Place the phone on the Hot Plate, with the
Display side down.
3.
Wait 10 minutes for the adhesive to warm up.
PAGE 56
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
4.
Use the thin Plastic Spudger to cut adhesive
from the top of the Battery.
5.
Use the thin Plastic Spudger to cut adhesive
from the sides of the Battery.
6.
Use the thin Plastic Spudger to cut adhesive
from the bottom of the Battery.
7.
Use fingers to remove the Battery from the
location as shown.
PAGE 57
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Coax Cable Removal
NOTE
The Coax Cable can be recovered
and reused after removal.
Use the Plastic Tweezer to remove the Coax
Cable from the location as shown.
PAGE 58
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Side Key FPC Removal
NOTE
After you remove the Side Key FPC, you
cannot reuse it.
Use the pointed end of the Black Stick to disengage
the Side Key FPC from the location as shown.
PAGE 59
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Proximity Sensor Grommet Removal
NOTE
The Proximity Sensor Grommet can be
recovered and reused after removal.
Use the Plastic Tweezer to remove the Proximity Sensor
Grommet from the location as shown.
PAGE 60
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Silicone Light Guide Removal
NOTE
The Silicone Light Guide can be
recovered and reused after removal.
Use the Plastic Tweezer to remove the Silicone Light
Guide from the location as shown.
PAGE 61
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
RF Thermal Silica Removal
NOTE
After you remove the RF Thermal Silica,
you cannot reuse it.
Use the Plastic Tweezer to remove the RF Thermal Silica
from the location as shown.
PAGE 62
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Power Thermal Silica Removal
NOTE
After you remove the Power Thermal
Silica, you cannot reuse it.
Use the Plastic Tweezer to remove the Power Thermal
Silica from the location as shown.
PAGE 63
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
LCD FPC Foam Removal
NOTE
After you remove the LCD FPC Foam,
you cannot reuse it.
Use the Plastic Tweezer to remove the LCD FPC Foam
from the location as shown.
PAGE 64
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Fingerprint Sensor Conductive Sponge Removal
NOTE
After you remove the Fingerprint Sensor
Conductive Sponge, you cannot reuse it.
Use the Plastic Tweezer to remove the Fingerprint
Sensor Conductive Sponge from the location as
shown.
PAGE 65
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Rear-Facing Camera Lens Removal
NOTE
Remove the Rear-Facing Camera Lens
only if it is defective or damaged.
Use the pointed end of the Black Stick to carefully
disengage and push out the Rear-Facing Camera
Lens from the location as shown.
PAGE 66
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Flash Lens Removal
NOTE
The Flash Lens can be recovered and
reused after removal.
Use the pointed end of the Black stick to gently push
out the Flash Lens from the location as shown.
PAGE 67
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Flash Lens Foam Removal
NOTE
After you remove the Flash Lens Foam,
you cannot reuse it.
Use the Plastic Tweezer to remove the Flash Lens
Foam from the location as shown.
PAGE 68
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
PARTS REFRESH
Tools Required for Parts Refresh
The following tools are required for parts refresh of the Moto g30 phone.
Description
Part #
Image
Plastic Tweezers
--
--
Black Stick
--
ESD Mat
--
--
Wrist Strap
--
--
Isopropyl (ISP) Alcohol
--
--
Cotton Swabs
--
--
Cleaning Pads
--
--
Gloves or Finger Collets
--
--
PAGE 69
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Battery Cover Cleaning
Use the ISP Alcohol and Cotton Swabs to remove
all the adhesives on the Battery Cover as shown.
/// CAUTION ///
Remove the adhesive carefully to avoid
damage to the Battery Cover.
PAGE 70
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Front Housing Cleaning
Use the Cotton Swabs with ISP Alcohol to remove
all the adhesives from the location as shown.
PAGE 71
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Top Bracket Cleaning
Use the Cotton Swabs with ISP Alcohol to remove
all the adhesives from the location as shown.
PAGE 72
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
ASSEMBLY
Assembly Map
Water
Detection
Label
Speaker Box
Waterproof
Film
USB
Grommet
Sub Board
Speaker Box
Rear-Facing
Camera
Conductive
Copper Foil
RF
Heat
Spreader
BB
Heat
Spreader
Rear-Facing
Camera
Rear-Facing
Camera
Conductive
Cloth
Front-Facing
Camera
Grommet
Water
Detection
Label
Front-Facing
Camera
Copper Foil
Audio
Jack
Grommet
Front-Facing
Camera
Main PCB
Water
Detection
Label
Primary
MIC Foam
Speaker
Dust Net
Foam
Top Bracket
Waterproof
Film
Secondary
MIC Foam
Power
Thermal
Silica
RF
Thermal
Silica
Sidekey
Waterproof
Film1
Sidekey
Waterproof
Film2
Sidekey
FPC
Coax
Cable
Receiver
Insulated Tap
Silicone
Light Guide
P-sensor
Grommet
Rear-Facing
Camera
Lens
Receiver
Vibrator
Water
Detection
Top
Bracket
Label
Battery
FPS
Conductive
Sponge
Flash Lens
Foam
Water
Receiver
Detection
Sealed
Foam
Label
Battery
Cover
LCD FPC
Foam
Front
Housing
IMEI Label
Sim Tray
PAGE 73
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Tools Required for Assembly
The following tools are required to assemble the Moto g30 phone.
Description
Part #
Black Stick
--
Torque Driver
--
PH00 Bit
--
Manual Roller
--
Plastic Tweezers
--
--
Tweezers
--
--
Gloves or Finger Collets
--
--
PAGE 74
Picture/Drawing
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Power Thermal Silica Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM716-BVJ000-003+Thermal silica_LD
3
Use the Plastic Tweezer to place and secure the
Power Thermal Silica on the location as shown.
PAGE 75
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
RF Thermal Silica Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM716-BVJ000-004+RF Thermal silica_LD
5
Use the Plastic Tweezer to place and secure the
RF Thermal Silica on the location as shown.
PAGE 76
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Water Detection Label Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNP316-096000-100+Water label
-
1.
Use the Plastic Tweezer to place the Water
Detection Label (WDL) on the Front-Housing
as shown.
2.
Use the Plastic Tweezer to place the Water
Detection Label (WDL) on the Front-Housing
as shown.
PAGE 77
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Vibrator Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNN901-BVU000-000+Flat motor_JX
39
Use the Plastic Tweezer to place and secure the
Vibrator on the location as shown.
PAGE 78
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Silicone Light Guide Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM716-BVJ000-010+LED silicone sleeve_DX
-
1.
Inspect the Silicone Light Guide for any
damage.
2.
Use the Plastic Tweezer to place and secure
the Silicone Light Guide on the location as
shown.
PAGE 79
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Proximity Sensor Grommet Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM716-BVJ000-009+P-S silicone sleeve_DX
-
Use the Plastic Tweezer to place and secure the
Proximity Sensor Grommet on the location as
shown.
NOTE
Use the point end of the Black Stick to press the
area which is marked in red to secure the
Proximity Sensor Grommet installed in place. Do
not press the other area of the Proximity Sensor
Grommet.
PAGE 80
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Receiver Sealed Foam Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM709-BVJ000-009+SPK seal Foam_KY
-
Use the Plastic Tweezer to place the Receiver
Sealed Foam on the location as shown and peel
off the liner.
PAGE 81
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Receiver Insulated Tape Assembly
Description
Reference #
TNN502-BQF000-010+Receive_DS
7
TNM701-BVJ002-004+earpiece insulating gl
8
Use the Plastic Tweezer to place the Receiver
Insulated Tape on the location as shown.
PAGE 82
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Receiver Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNN502-BQF000-010+Receive_DS
7
Use the Plastic Tweezer to place the Receiver on
the location as shown.
NOTE
Make sure the Receiver should be in correct
direction with the contact on the bottom.
PAGE 83
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Water Detection Label Assembly
Description
Reference #
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNP316-096000-100+Water label
-
Use the Plastic Tweezer to place the Water
Detection Label (WDL) on the Main PCB as
shown.
PAGE 84
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
BB Heat Spreader Assembly
Description
Reference #
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNM721-BVU001-002+Graphite Sheet/LS
-
Use the Plastic Tweezer to place the BB Heat
Spreader on the Main PCB as shown.
NOTE
Make sure to assemble the BB Heat Spreader
along the red lines as marked.
PAGE 85
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
RF Heat Spreader Assembly
Description
Reference #
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNM721-BVU001-001+Graphite Sheet/LS
-
Use the Plastic Tweezer to place the RF Heat
Spreader on the Main PCB as shown.
NOTE
Make sure to assemble the RF Heat Spreader
along the red lines as marked.
PAGE 86
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
8M Rear-Facing Camera Assembly
Description
Reference #
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
MDL,CAMR,8M,rear,;C08F31;Q Tech,AF:capri
23
Use fingers to place and secure the 8M RearFacing Camera on the Main PCB as shown.
PAGE 87
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
64M Rear-Facing Camera Assembly
Description
Reference #
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
MDL,CAMR,64M,after,;L64BA10;O-FILM,AF:Ki
24
Use fingers to place and secure the 64M RearFacing Camera on the Main PCB as shown.
PAGE 88
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Audio Jack Grommet Assembly
Description
Reference #
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNM716-BVJ000-005+EAR silicone sleeve_DX
11
Use the Plastic Tweezer to place the Audio Jack
Grommet on the location as shown.
PAGE 89
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Main PCB Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNM501-211103-011+round head screw
-
1.
Use fingers to place the Main PCB on the
location as shown.
2.
Use the Torque Driver with PH00 Bit to tighten
the two screws as shown (0.75 ± 0.1 kgf.cm).
PAGE 90
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2M Depth Rear-Facing Camera Conductive Cloth Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNM715-BVJ002-009+conductive adhesive
27
Use the Plastic Tweezer to place the 2M Depth
Rear-Facing Camera Conductive Cloth on the
location as shown.
PAGE 91
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2M Macro Rear-Facing Camera Copper Foil Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNM715-BVJ002-014+Posterior adhesive_APL
28
Use the Plastic Tweezer to place the 2M Macro
Rear-Facing Camera Copper Foil on the location as
shown.
PAGE 92
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2M Macro Rear-Facing Camera Assembly
Description
Reference #
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNN703-BVJ003-020+2M Camera Module LH,
26
Use fingers to place and secure the 2M Macro
Rear-Facing Camera on the Main PCB as shown.
PAGE 93
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2M Depth Rear-Facing Camera Assembly
Description
Reference #
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
MDL,CAMR,2M,rear,;L02BF40;O-FILM:Capri/C
25
Use fingers to place and secure the 2M Depth
Rear-Facing Camera on the Main PCB as shown.
PAGE 94
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Front-Facing Camera Grommet Assembly
Description
Reference #
TNM716-BVU000-001+Silicone sleeve/DX
2
MDL,CAMR,13M,front;C0DF03;Kunshan,FF:Cap
4
1.
Use the Plastic Tweezer to place the FrontFacing Camera Grommet on the location as
shown.
2.
Exact position for Front-Facing Camera
Grommet as shown.
PAGE 95
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Front-Facing Camera Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
MDL,CAMR,13M,front;C0DF03;Kunshan,FF:Cap
4
Use fingers to place and secure the Front-Facing
Camera on the Main PCB as shown.
PAGE 96
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Front-Facing Camera Copper Foil Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNM719-BVJ001-002+CAM ground copper foil
6
Use the Plastic Tweezer to place and secure the
Front-Facing Camera Copper Foil on the location
as shown and peel off the liner.
NOTE
Assemble the Front-Facing Camera Copper
Foil along the top left corner of the FrontFacing Camera.
PAGE 97
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Side Key FPC Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
TNN802-BVJ000-000+SIDEKEY_FPC FIN part_Z
30
1.
Use the Plastic Tweezer to place the Side Key
FPC on the location as shown.
2.
Use fingers to place and secure the Side Key
FPC on the location as shown.
NOTE
Press firmly for seconds 3 times to activate the
adhesive.
PAGE 98
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
3.
Use the Plastic Tweezer to lock the Side Key
FPC on the location as shown.
4.
Use fingers to place and secure the Display
Flex BtB connector on the Main PCB as
shown.
PAGE 99
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
LCD FPC Foam Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM709-BVJ003-026+LCD FPC foam_APLT
-
Use the Plastic Tweezer to place the LCD FPC
Foam on the location as shown.
NOTE
Care the top of the sponge must not exceed the
surface of the Sub Board, and the both left and
right sides should not be attached to the Front
Housing.
PAGE 100
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Water Detection Label Assembly
Description
Reference #
XT2129-1 Sub Baord&S102-BVU000-000CS
XT2129-2 Sub Board&S102-BVU000-001CS
ASSY,DTR BRD,Capri Plus BR
34
TNP316-096000-100+Water label
-
Use the Plastic Tweezer to place the Water
Detection Label (WDL) on the Sub Board as
shown.
PAGE 101
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
USB Grommet Assembly
Description
Reference #
XT2129-1 Sub Baord&S102-BVU000-000CS
XT2129-2 Sub Board&S102-BVU000-001CS
ASSY,DTR BRD,Capri Plus BR
34
TNM716-BVJ000-007+T-C silicone sleeve_DX
37
Use the Plastic Tweezer to place the USB
Grommet on the location as shown.
PAGE 102
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Sub Board Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 Sub Baord&S102-BVU000-000CS
XT2129-2 Sub Board&S102-BVU000-001CS
ASSY,DTR BRD,Capri Plus BR
34
TNM501-211103-011+round head screw
-
1.
Use fingers to place the Sub Board on the
location as shown.
2.
Use the Torque Driver with PH00 Bit to
tighten the screw as shown (0.75 ± 0.1
kgf.cm).
3.
Use fingers to place and secure the LCM
BtB Connector on the location as shown.
PAGE 103
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Coax Cable Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
XT2129-1 Sub Baord&S102-BVU000-000CS
XT2129-2 Sub Board&S102-BVU000-001CS
ASSY,DTR BRD,Capri Plus BR
34
TNEI06-320817-000+RF COA LIN 119.5_0.81
9
1.
Use the Plastic Tweezer to place the Coax
Cable on the Main PCB as shown.
2.
Use the Plastic Tweezer to place the Coax
Cable on the Sub Board as shown.
PAGE 104
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Battery Adhesive Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM715-BVJ001-001+Battery Adhesive_AP
38
Use the Plastic Tweezer to place and secure the
Battery Adhesive on the location as shown and
peel off the liner.
NOTE
Make sure to assemble the Battery Adhesive
according to the silk print lines as marked in red.
PAGE 105
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Battery Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
ACCY,BAT,5000mAh,ACCY,BAT,5000mAh,JK50,L
31
/// WARNING ///
// CAUTION //
Failure to adhere to Safety Critical Note(s) may
increase risk of rupture, burning, or failure to
function safely when used by the customer.
Refer to the Battery Safety Guidelines.
Handle the Battery Pack with care. If dropped to the
floor, it may be internally damaged and must be
scrapped.
Ensure Battery and its insulation are not damaged (e.g.
scratched, dented, punctured) prior to and throughout
assembly.
Prior to assembly, ensure Battery edges and surfaces
are not dented or deformed, and that fixtures and parts
that will contact the Battery are free of foreign material.
Ensure screws and screwdrivers do not contact the
Battery.
1.
Use fingers to place the Battery on the Front
Housing as shown.
NOTE
Make sure to assemble the Battery using the
bottom left corner marked as red.
PAGE 106
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
2.
Use fingers to press and secure the Battery
BtB Connector as shown.
3.
Use the Manual Roller to roll over the Battery
for 10 cycles to secure the Battery as shown.
NOTE
For each cycle roll the Manual Roller from top to
bottom of the Battery and vice versa.
NOTE
Each cycle should last for 3 seconds.
PAGE 107
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
FPS Flex Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 MB_4+128G DS&F00BVU3-000-000CS
XT2129-1 MB_4+128G_SS&F00BVU3-000-001CS
XT2129-2 MB_4+128G DS&F00BVU3-000-002CS
XT2129-2 MB_4+128G SS&F00BVU3-000-003CS
XT2129-2 MB_4+64G_DS&F00BVU3-000-004CS
XT2129-2 MB_6+128G_DS&F00BVU3-000-005CS
XT2129-3 MB_6+128G_DS&F00BVU3-000-006CS
ASSY,BD KIT,Capri Plus 4+128 DS BR
10
FINGERPRT SCANNER,Phantom Black,FPC1520
FINGERPRT SCANNER,Pastel sky,FPC1520
FINGERPRT SCANNER,Phantom Black,FPC1520,
FINGERPRT SCANNER,Pastel Sky,FPC1520,no
17
Use fingers to place the FPS Flex on the
location as shown.
PAGE 108
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Flash Lens Foam Assembly
Description
Reference #
TNM709-BVJ001-023+flash cover seal Foam_
12
TNM223-BVJ000-000+Flash COV_TRA_rear/HG
13
Use the Plastic Tweezer to place the Flash Lens
Foam on the location as shown.
PAGE 109
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Flash Lens Adhesive Assembly
Description
Reference #
TNM223-BVJ000-000+Flash COV_TRA_rear/HG
13
TNM715-BVJ001-007+flash cover Adhesive_A
14
Use the Plastic Tweezer to place the Flash Lens
Adhesive on the location as shown and peel off
the liner.
PAGE 110
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Flash Lens Assembly
Description
Reference #
TNM223-BVJ000-000+Flash COV_TRA_rear/HG
13
XT2129-1 Up frame_PB&S101-BVU135-200CS
XT2129-1 UP Frame_PS&S101-BVU055-200CS
XT2129-2 UP Frame_PB&S101-BVU136-200CS
XT2129-2 UP Frame_PS&S101-BVU056-200CS
15
Use the Plastic Tweezer to place the Flash Lens on
the location as shown.
NOTE
Press firmly for seconds 3 times to activate the
adhesive.
PAGE 111
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Rear-Facing Camera Lens Adhesive Assembly
Description
Reference #
TNM715-BVJ001-000+Camera Lens Adhesive
21
TNM205-BVU130-000+rear lens/black/DT
TNM205-BVU050-000+rear lens/white/DT
20
Use the Plastic Tweezer to place and secure the
Rear-Facing Camera Lens Adhesive on the
location as shown and peel off the liner.
PAGE 112
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Rear-Facing Camera Lens Assembly
Description
Reference #
XT2129-1 Up frame_PB&S101-BVU135-200CS
XT2129-1 UP Frame_PS&S101-BVU055-200CS
XT2129-2 UP Frame_PB&S101-BVU136-200CS
XT2129-2 UP Frame_PS&S101-BVU056-200CS
15
TNM205-BVU130-000+rear lens/black/DT
TNM205-BVU050-000+rear lens/white/DT
20
Use the Plastic Tweezer to place the Rear-Facing
Camera Lens on the location as shown.
NOTE
Press firmly for seconds 3 times to activate the
adhesive.
PAGE 113
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Top Bracket Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 Up frame_PB&S101-BVU135-200CS
XT2129-1 UP Frame_PS&S101-BVU055-200CS
XT2129-2 UP Frame_PB&S101-BVU136-200CS
XT2129-2 UP Frame_PS&S101-BVU056-200CS
15
TNM501-211102-020+round head screw
-
1.
Use fingers to place the Top Bracket on the
location as shown.
2.
Use the Torque Driver with PH00 Bit to tighten
the nine white screws as shown (0.8 ± 0.1
kgf.cm).
PAGE 114
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
FPS Adhesive Assembly
Description
Reference #
XT2129-1 Up frame_PB&S101-BVU135-200CS
XT2129-1 UP Frame_PS&S101-BVU055-200CS
XT2129-2 UP Frame_PB&S101-BVU136-200CS
XT2129-2 UP Frame_PS&S101-BVU056-200CS
15
TNM715-BVJ001-008+FPS adhesive_AP
-
Use the Plastic Tweezer to place and secure the
FPS Adhesive on the location as shown and peel
off the liner.
PAGE 115
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
FPS Conductive Sponge Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 Up frame_PB&S101-BVU135-200CS
XT2129-1 UP Frame_PS&S101-BVU055-200CS
XT2129-2 UP Frame_PB&S101-BVU136-200CS
XT2129-2 UP Frame_PS&S101-BVU056-200CS
15
TNM709-BVJ000-001+FP Conductive sponge1
-
1.
Use the Plastic Tweezer to place the FPS
Conductive Sponge on the location as shown.
2.
Use fingers to place the Fingerprint sensor on
the location aligning with pins as shown.
NOTE
Press firmly for seconds 3 times to activate the
adhesive.
PAGE 116
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Speaker Box Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129 Speaker Box&S108-BVU000-000CS
32
TNM501-211105-006+round head screw_LJT
-
1.
Use fingers to place the Speaker Box on the
location as shown.
2.
Use Torque Driver with PH00 Bit to tighten the
seven black screws as shown (0.8 ± 0.1
kgf.cm).
PAGE 117
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Side Key Waterproof Film 1 Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM701-BVJ001-002+Waterproof membrane/AP
29
Use the Plastic Tweezer to place the Side Key
Waterproof Film 1 on the location as shown and
peel off the liner.
NOTE
Assemble the Side Key Waterproof Film 1
according to aligning keys.
PAGE 118
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Side Key Waterproof Film 2 Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 Up frame_PB&S101-BVU135-200CS
XT2129-1 UP Frame_PS&S101-BVU055-200CS
XT2129-2 UP Frame_PB&S101-BVU136-200CS
XT2129-2 UP Frame_PS&S101-BVU056-200CS
15
TNM701-BVJ002-006+LCMSide WaterproofFilm
18
Use the Plastic Tweezer to place the Side Key
Waterproof Film 2 on the location as shown and
peel off the liner.
PAGE 119
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Secondary MIC Foam Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM709-BVJ001-011+MIC dust net Foam_AP
42
Use the Plastic Tweezer to place the Secondary
MIC Foam on the location as shown.
PAGE 120
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Top Bracket Waterproof Film Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 Up frame_PB&S101-BVU135-200CS
XT2129-1 UP Frame_PS&S101-BVU055-200CS
XT2129-2 UP Frame_PB&S101-BVU136-200CS
XT2129-2 UP Frame_PS&S101-BVU056-200CS
15
TNM701-BVJ001-000+Waterproof membrane/AP
16
Use the Plastic Tweezer to place the Top Bracket
Waterproof Film on the location as shown and peel
off the liner.
NOTE
Assemble the Top Bracket Waterproof Film
along the positioning line marked in red.
PAGE 121
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Primary MIC Foam Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM709-BVJ001-011+MIC dust net Foam_AP
42
Use the Plastic Tweezer to place the Primary
MIC Foam on the location as shown.
PAGE 122
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Speaker Dust Net Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM711-BVJ001-000+Speaker dust net_AP
41
Use the Plastic Tweezer to place the Speaker
Dust Net on the location as shown.
PAGE 123
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Speaker Box Waterproof Film Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNM701-BVJ001-001+Waterproof membrane/AP
40
Use the Plastic Tweezer to place and secure the
Speaker Box Waterproof Film on the location as
shown and peel off the liner.
PAGE 124
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Rear-Facing Camera Decoration Adhesive Assembly
Description
Reference #
XT2129-1 Batt Cover_PB&S101-BVU137-300CS
XT2129-1 Batt Cover_PS&S101-BVU057-300CS
Capri+ etching_BR_PB&S101-BVU13B-300CS
Capri+ etching_BR_PS&S101-BVU05B-300CS
XT2129-2 Batt Cover_PB&S101-BVU138-300CS
XT2129-2 Batt Cover_PS&S101-BVU058-300CS
XT2129-3 Batt Cover_PB&S101-BVU139-300CS
XT2129-3 Batt Cover_PS&S101-BVU059-300CS
Capri+ etching_LA_PB&S101-BVU13A-300CS
Capri+ etching_LA_PS&S101-BVU05A-300CS
Capri+ etching_EU_PB&S101-BVU13C-300CS
Capri+ etching_EU_PS&S101-BVU05C-300CS
Capri+ etching_UK_PB&S101-BVU13I-300CS
Capri+ etching_UK_PS&S101-BVU05I-300CS
Capri+ etching_APEM_PB&S101-BVU13E-300CS
Capri+ etching_APEM_PS&S101-BVU05E-300CS
XT2129-3 etching_PB&S101-BVU13G-300CS
XT2129-3 etching_PS&S101-BVU05G-300CS
22
TNM715-BVJ001-004+decoration Adhesive_AP
-
Use the Plastic Tweezer to place the Rear-Facing
Camera Decoration Adhesive on the location as
shown and peel off the liner.
PAGE 125
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
FPS Sealed Foam Adhesive Assembly
Description
Reference #
XT2129-1 Batt Cover_PB&S101-BVU137-300CS
XT2129-1 Batt Cover_PS&S101-BVU057-300CS
Capri+ etching_BR_PB&S101-BVU13B-300CS
Capri+ etching_BR_PS&S101-BVU05B-300CS
XT2129-2 Batt Cover_PB&S101-BVU138-300CS
XT2129-2 Batt Cover_PS&S101-BVU058-300CS
XT2129-3 Batt Cover_PB&S101-BVU139-300CS
XT2129-3 Batt Cover_PS&S101-BVU059-300CS
Capri+ etching_LA_PB&S101-BVU13A-300CS
Capri+ etching_LA_PS&S101-BVU05A-300CS
Capri+ etching_EU_PB&S101-BVU13C-300CS
Capri+ etching_EU_PS&S101-BVU05C-300CS
Capri+ etching_UK_PB&S101-BVU13I-300CS
Capri+ etching_UK_PS&S101-BVU05I-300CS
Capri+ etching_APEM_PB&S101-BVU13E-300CS
Capri+ etching_APEM_PS&S101-BVU05E-300CS
XT2129-3 etching_PB&S101-BVU13G-300CS
XT2129-3 etching_PS&S101-BVU05G-300CS
22
TNM715-BVJ001-005+FP seal adhesive_AP
-
Use the Plastic Tweezer to place and secure the
FPS Sealed Foam Adhesive on the location as
shown and peel off the liner.
PAGE 126
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Battery Cover Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
XT2129-1 Batt Cover_PB&S101-BVU137-300CS
XT2129-1 Batt Cover_PS&S101-BVU057-300CS
Capri+ etching_BR_PB&S101-BVU13B-300CS
Capri+ etching_BR_PS&S101-BVU05B-300CS
XT2129-2 Batt Cover_PB&S101-BVU138-300CS
XT2129-2 Batt Cover_PS&S101-BVU058-300CS
XT2129-3 Batt Cover_PB&S101-BVU139-300CS
XT2129-3 Batt Cover_PS&S101-BVU059-300CS
Capri+ etching_LA_PB&S101-BVU13A-300CS
Capri+ etching_LA_PS&S101-BVU05A-300CS
Capri+ etching_EU_PB&S101-BVU13C-300CS
Capri+ etching_EU_PS&S101-BVU05C-300CS
Capri+ etching_UK_PB&S101-BVU13I-300CS
Capri+ etching_UK_PS&S101-BVU05I-300CS
Capri+ etching_APEM_PB&S101-BVU13E-300CS
Capri+ etching_APEM_PS&S101-BVU05E-300CS
XT2129-3 etching_PB&S101-BVU13G-300CS
XT2129-3 etching_PS&S101-BVU05G-300CS
22
Use fingers to place the Battery Cover on the
Front-Housing and press it on all sides as shown.
NOTE
Press firmly for seconds 3 times to activate the
adhesive.
PAGE 127
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
IMEI Label Assembly
Description
Reference #
TNEI30-BVJ130-000+sim card tray_black_JH
TNEI30-BVJ131-000+sim card tray_black_JH
TNEI30-BVJ050-000+sim card tray_white_JH
TNEI30-BVJ051-000+sim CAR TRA_PAS WHI_JH
19
Use the Plastic Tweezer to place and secure the
IMEI Label on the location as shown.
PAGE 128
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Sim Tray Assembly
Description
Reference #
XT2129 TP LCM&S101-BVU130-000CS
XT2129 TP LCM_IN&S101-BVU131-000CS
1
TNEI30-BVJ130-000+sim card tray_black_JH
TNEI30-BVJ131-000+sim card tray_black_JH
TNEI30-BVJ050-000+sim card tray_white_JH
TNEI30-BVJ051-000+sim CAR TRA_PAS WHI_JH
19
XT2129-1 Batt Cover_PB&S101-BVU137-300CS
XT2129-1 Batt Cover_PS&S101-BVU057-300CS
Capri+ etching_BR_PB&S101-BVU13B-300CS
Capri+ etching_BR_PS&S101-BVU05B-300CS
XT2129-2 Batt Cover_PB&S101-BVU138-300CS
XT2129-2 Batt Cover_PS&S101-BVU058-300CS
XT2129-3 Batt Cover_PB&S101-BVU139-300CS
XT2129-3 Batt Cover_PS&S101-BVU059-300CS
Capri+ etching_LA_PB&S101-BVU13A-300CS
Capri+ etching_LA_PS&S101-BVU05A-300CS
Capri+ etching_EU_PB&S101-BVU13C-300CS
Capri+ etching_EU_PS&S101-BVU05C-300CS
Capri+ etching_UK_PB&S101-BVU13I-300CS
Capri+ etching_UK_PS&S101-BVU05I-300CS
Capri+ etching_APEM_PB&S101-BVU13E-300CS
Capri+ etching_APEM_PS&S101-BVU05E-300CS
XT2129-3 etching_PB&S101-BVU13G-300CS
XT2129-3 etching_PS&S101-BVU05G-300CS
22
1.
Insert the SIM Tray in the transceiver as
shown.
2.
Use finger to press the SIM Tray until it secures
into the transceiver.
PAGE 129
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
ASSEMBLY QUALITY CHECK
Battery Quality Check
Check the quality of battery make sure
no deform or defect on it
PAGE 130
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Grommet and Connectors Quality Check
PAGE 131
Lenovo Confidential Restricted:
Do not share without consent from Lenovo
Lenovo Moto g30
Level 2 – Service and Repair Manual
Screws Graphite Quality Check
Check if any missing/misaligned waterproof.
Check if any missing/unseated screws.
Check if any missing/unseated screws.
Check if any missing/misaligned waterproof.
PAGE 132
Lenovo Confidential Restricted:
Do not share without consent from Lenovo