dahao-a15-user-manual

Computerized Embroidery Machine Controller
BECS-A15
OWNER’S MANUAL
Conteents
Conteents
Chaptter 1 Genneral Infoormation
1.1 Warnings
W
a Cautioons .................................................................................... 1
and
1.2 Main
M Featuures .................................................................................................. 3
1.3 Technical
T
S
Specificati
ions .................................................................................. 6
Chaptter 2 Embbroidery Guide
2.1 Structure
S
a Usage Instructioon of Conttrol Panel .......................................... 7
and
2.2 Innstructionn of the Maain Interfaace ..................................................................... 8
2.3 Basic
B
Procedure of Embroider
E
ry ..................................................................... 15
2.4 Normal
N
Em
mbroidery,, Returninng and Patcching .............................................. 19
2.5 Embroidery
E
y Operatioon ................................................................................... 19
2.6 Thread-Bre
T
eakage Deetection ........................................................................... 19
2.7 Working
W
Sttatus ............................................................................................... 20
Chaptter 3 U Disk
D Mannagementt
3.1 Select
S
U Disk
D ................................................................................................. 22
3.2 Pattern
P
Preeview .............................................................................................. 24
3.3 Pattern
P
Inpput................................................................................................... 25
....................................................................................... 26
3.4 Directory
D
O
Operation
3.5 Formatting
F
g U Disk ......................................................................................... 26
3.6 Delete
D
Objects from U Disk (iincluding pattern
p
fille and direectory) ............. 27
3.7 Create
C
a Neew Directtory in thee Current Directory
D
........................................ 28
Chaptter 4 Com
mmon Paarameterss and Color-Channging Ordder
4.1 Settings
S
off Commonn Parameteers ................................................................... 29
Owner’s Manual
M
of BECS- A15 Computerized Controll System
I
Contents
4.1.1. Settings of X-Y Scale ............................................................................................ 30
4.1.2. Settings of Rotate Angle........................................................................................ 31
4.1.3. Pattern Direction ................................................................................................... 32
4.1.4. Prior Mode ............................................................................................................ 32
4.1.5. Rep. Mode ............................................................................................................. 32
4.1.6. Rep. Order ............................................................................................................. 32
4.1.7. X-Y Rep. Times..................................................................................................... 33
4.1.8. X-Y Rep. Interval .................................................................................................. 33
4.2 Settings of Color-changing Order ................................................................33
4.2.1. Color-changing Interface....................................................................................... 33
4.2.2. Settings of Color-Changing Order ........................................................................ 35
4.2.3. Set Needle Bar Color ............................................................................................ 35
Chapter 5 Settings of Embroidery Parameters
5.1 Procedure for Setting General Parameters ...................................................38
5.2 Instruction on Some Functions within General Parameters .........................39
5.2.1. Cyclic Embroidery Function ................................................................................. 39
5.2.2. Brake Adjustment (A Must for New Machine) ..................................................... 39
Chapter 6 Memory Pattern Management
6.1 Memory Pattern Management Interface and Other Memory Pattern
Operation Interfaces ..............................................................................................40
6.2 Select Pattern for Embroidery ......................................................................42
6.3 Memory Pattern Preview ..............................................................................42
6.4 Pattern Output...............................................................................................44
6.5 Copy the Memory Pattern ............................................................................46
II
Owner ’s Manual of BECS- A15 Computerized Control System
Conteents
6.6 Create
C
Outtline Patterrn.................................................................................... 48
6.7 Create
C
Higgh-speed Pattern
P
............................................................................. 48
6.8 Divide
D
Patttern ................................................................................................ 48
6.9 Create
C
Paraameter Paattern ............................................................................... 49
6.10 Mosaic Paattern ............................................................................................. 50
6.11 Create Coombined Pattern
P
............................................................................. 51
6.12 Satin Stitcch Adjustm
ment ............................................................................... 54
Chaptter 7 Lettter Patterrn Operattion
7.1 Enter
E
Mainn Interfacee for Letteer Embroid
dery................................................. 55
7.2 Innput Letteer String foor Embroiidery ................................................................ 55
7.3 Adjust
A
Lettter Patternn ...................................................................................... 56
7.4 Save
S
Letterr Pattern ......................................................................................... 60
Chaptter 8 Assiistant Opperation
8.1 Frame
F
Seleection ............................................................................................. 62
8.2 Clear
C
XY Displacem
D
ment ................................................................................. 63
8.3 Positioning
P
g Idling........................................................................................... 63
8
8.3.1.
Low Speed
S
Idlingg Forward ........................................................................................ 63
8
8.3.2.
Low Speed
S
Idlingg Backwardd .................................................................................... 64
8
8.3.3.
High Speed Idlinng Forward ...................
.
................................................................... 64
8
8.3.4.
Go to Next Colorr ....................................................................................................... 64
Chaptter 9 Othher Functiions
9.1 Statistics
S
.......................................................................................................... 65
9.2 Set
S Frame Origin............................................................................................ 67
Owner’s Manual
M
of BECS- A15 Computerized Controll System
III
Contents
9.3 Language ......................................................................................................68
9.4 Machine Information ....................................................................................68
9.5 Machine Debugging .....................................................................................69
9.6 Date and Time ..............................................................................................70
9.7 Touch Screen Correction ..............................................................................70
Chapter 10 Online Update of Main Software
Chapter 11 Update of Software in Peripheral Board
Appendix 1 Parameter List
Appendix 2 Directions of U Disk Operation
Appendix 3 Automatic Position Limitation Function Instructions for
Apparel Embroidery
Appendix 4 A15 Controller Operation Quick Guide
There will be no further notice in case of any change of specifications.
IV
Owner ’s Manual of BECS- A15 Computerized Control System
C
Chapter
1
Geneeral Inforrmation
Ch
hapterr 1 General Innformaation
T
Thank
you for
fo using Daahao Compuuterized Con
ntrol System
m for Embrooidery Macchine.
Pleasee read this manual
m
careffully so as to
t operate th
he machine correctly annd effectiveely.
Besidees that, you should keepp this manuual properly
y for future use.
u
1.1 Warnings
W
a Cautions
and
In order to avooid fire, eleectrical shocck or unpred
dicted injuriies, you shoould follow the listed
safety ruules.
Matterrs for Attention on Usaage
Dangerr
Duuring the opperation, do not try to
t open thee machine bbox. The high
h
voltagee
conntained in some
s
parts is deadly. Th
he rotating parts
p
may ccause seriou
us injury.
Forbiddden
Doon't expose the
t machinee to humiditty gas, poisonous gas, water, and dust.
d
Forbiddden
Doon’t store orr operate thee machine in the vibrattion area, w
which may cause troublee
to the machinee.
Attentiion
Pleease abide all
a the warniings and saffety requireements to ennsure the seccurity.
Attentiion
LC
CD screen iss fragile. Doo not use the hard or shharp item too click the sccreen.
Attentiion
Pleease insert U disk correectly and do
on’t force it in, otherwiise, USB intterface or U
dissk may get damaged
d
Attentiion
Wee will add appendix
a
if necessary. If
I there is any
a differennce between
n the manuaal
andd appendix,, the contennt in the appendix shall take preceddence.
Matterss for Attenttion on Tran
nsportation
n and Load
ding
Attentiion
Whhen movingg the machinne, please not
n to hold thhe cable.
Attentiion
Pleease abide all
a the warniings and saffety requireements to ennsure the seccurity.
Comppulsory Ovverloading may
m cause serious losss. Please load accordinng to the in
nstruction onn
thee box
Requiremeents
Owner’s Manual
M
of BECS- A15 Computerized Controll System
1
Chapter 1
General Information
Matters for Attention on Installation
Attention
Don't jam the vent on the device. Don’t insert other items into the machine, or it
may get fire.
Attention
Make sure the installation direction is correct.
Attention
Don't expose the machine to humidity gas, corrosive gas, water, and other
flammable material.
Matters for Attention on Cable Connection
Forbidden
Don't test the insulation of the circuit loop.
Forbidden
Never try to connect the overloaded electronic device on the connectors (like
sockets or terminals).
Attention
The insulation condition of each cable (no matter signal cable or power cable)
should be ensured.
Attention
The signal cables and power cables should be separated. Never tie them together.
Attention
All the cables should be well fixed. Don’t put any strength on cables. Make sure
each turning point of cable is well protected. Add shelter pipes to increase
insulating capability if necessary.
Attention
Machine should be grounded reliably. The resistance should be smaller than 10
.
Matters for Attention on Operation
Danger
Don't operate the machine when there is any damage on the shelter of the running
parts.
Forbidden
When machine is running, do not touch any running part.
Attention
Make sure the configuration of power supply is in normal. Use stabilized voltage
power supply when the change of voltage is beyond the range of -10%~10%.
Attention
In case of warning, please check out the problem. Operation can only be carried
out again when problem is solved.
Attention
The power supply switch has over-current protection function. If the over-current
switch is activated, the switch can only be closed after 3 minutes.
2
Owner ’s Manual of BECS- A15 Computerized Control System
C
Chapter
1
Geneeral Inforrmation
Matterss for Attenttion on Maiintenance and
a Inspecttion
Warninng
If you
y need too open the machine co
over, pleasee cut off thee power sup
pply at firstt.
Duue to the cappacitance, operator
o
mu
ust wait at leeast one minnute before opening thee
maachine cover.
Attentiion
b static. The
T
circuitt boards can only bee
Cirrcuit boardds can be damaged by
dissassembled by professional techniccians.
Attenttion
If machine
m
is inactive forr a while teemporarily, users must power on the
t machinee
reggularly (oncce by every 2 or 3 days, more thann an hour forr each time)).
Attentiion
If machine is inactive foor a long tiime, users should
s
havee the machiine checkedd
beffore power--on.
Matters for
f Attentio
on on Rejecction
Attentiion
Reejection shoould obey the rules and regulaations set by nationaal industriaal
eleectronic stanndards.
1.2 Main
M
Featu
ures
1.
User-frienndly Interfacce on Touchhing Panel
Thhe adoptionn of the touuching paneel technolog
gy offers usser the delightful operration and
easy learning. Thee beautiful screen
s
display turns eveeryday workk into joyfuul experiencces.
2.
Huge Mem
mory Capaccity
m
stitcches, whichh can meet ddemands off different
Thhe memory capacity reaaches 100 million
customeers.
3.
Maximum
m Stitch Amoount of Onee Pattern Reeaches Two Million
At present a single patterrn in the sysstem has thee maximum
m of 2 millioon stitches and
a 1,000
times off automatic color changging.
4.
Multi-Taskk Parallel Operation
O
annd Free Shifft among Taasks
Duuring the em
mbroidery, actions
a
like pattern inp
put & outpuut, preparatiion for the following
patternss and modifi
fication of parameters
p
c be carrieed out.
can
5.
Storage off Frequentlyy Used Paraameters and Color-Channging Orderr for Each Pattern
P
Patttern will be
b saved allong with its parameteers, color-cchanging orrders and needle
n
bar
colors. System cann save the opperational details
d
for each
e
patternn. Users cann set parameeters for a
Owner’s Manual
M
of BECS- A15 Computerized Controll System
3
Chapter 1
General Information
pattern during the embroidery process of the previous pattern, which will save time and
improve efficiency. Moreover, it is one basis to realize network management.
6.
Pattern Input/Output via USB
Customers can use USB disk for data transfer. USB disk supports DIR operation, which is
easy for pattern management. For each directory, system supports operation of 400 patterns or
sub-directory. There is no limitation of directory levels. Patterns in the formats of Binary,
Ternary and Z-nary can be loaded.
7.
Patch Embroidery
This function can set a patch point at the position of color code or stop code, and when the
machine embroiders to the patch point, it will halt and move out frame for patching. After
sticking a patch, user would press the start key to return the frame and continue embroidering.
8.
Brake Adjustment
User can adjust the parameter of brake to let the main shaft stop at the correct position
according to the characters of his own machines.
9.
Save Start Point
This function can save the start point of each pattern, which saves the work of user to
search the start point manually at embroidering the identical pattern.
10.
Mechanical Maintainence and Debugging
This function is to easily judge the malfunctions at maintaining and debugging the
machine, such as encoder testing, main shaft speed testing, machine parts testing and the main
shaft stopping at any position, etc.
11.
Multi-Language Support
Currently, the system only supports Chinese and English; Arabic, Spanish, Turkish,
Russian, Portuguese, French and many other languages are under developing.
12.
Pattern Output
Patterns can be output and saved into USB disk. Adoption of TAJIMA’s binary format
enjoys the advantage of data transmitting through the World Wide Web (other formats may not
be transmitted directly).
4
Owner ’s Manual of BECS- A15 Computerized Control System
C
Chapter
1
13.
Geneeral Inforrmation
Repetitionn Embroideery
vity by usiing the funnction of repetition
Thhe user cann increase embroideryy productiv
embroiddery, which can also bee used with cyclic embrroidery.
14.
Cyclic Em
mbroidery
Wiith this funcction, the machine
m
cann automaticaally return to the origiin and start the same
embroiddery again when finishing the paattern one time. User also can increase pro
oductivity
rapidly by combiining this function with
w
speciaal pattern-m
making funnction or repetition
embroiddery functioon.
15.
Pattern Compiling
C
(1)) Compilingg the Data of
o Selected Pattern
P
to Generate
G
Neew Pattern
Ussers can com
mpile any pattern
p
accorrding to zoo
om ratio, rootate angle, normal rep
petition or
partial repetition
r
too generate a new patterrn and save it to memoory. The new
wly generateed pattern
can be used
u
for em
mbroidering, output or other
o
operatiions.
(2)) Compilingg the Combiined Patternn
Affter setting the
t combineed pattern, the
t system can compille that patteern to generate a new
one andd save it to memory. Thhe newly generated paattern can be used for eembroiderin
ng, output
or otherr operations.
16.
Letter Patttern
Thhere are 28 built-in
b
fonnt libraries. Users
U
can make
m
letter groups andd change letter orders
accordinng to differeent tasks. Thhis operatioon is vivid, simple
s
and easy managging.
17.
Pattern Edit (under developing)
d
18.
Speed Addjustment
Thhe highest speed for em
mbroidery can
c be presset. During embroideryy, speed maay change
automattically alongg with the change
c
of neeedle interv
val.
19.
Thread-ttrimming
Thhread-trimm
ming can be
b manuallly operateed. The machine
m
caan trim th
he thread
automattically at thee end of em
mbroidery prrocess or at color-changging.
20.
Thread-bbreakage Detection
D
Owner’s Manual
M
of BECS- A15 Computerized Controll System
5
Chapter 1
General Information
In case of thread breakage or running-out of bobbin thread, the machine will stop and give
warning by indicator.
21.
Color-changing
At the color-changing point, user can either perform the color-changing manually or let
the system do it automatically according to the preset order.
1.3 Technical Specifications
6
1.
Maximum number of patterns saved in memory: 800
2.
Memory capacity: 100 million stitches
3.
Screen resolution ratio: 1280*800
4.
Network port speed: 100Mbps
5.
Supported method for data exchange: USB disk, network (temporarily unavailable)
6.
Control precision: Minimum controllable stitch interval is 0.1mm
7.
Stitch range: 0.1mm~12.7mm
Owner ’s Manual of BECS- A15 Computerized Control System
C
Chapter
r2
Emb
broidery Guide
mbroid
dery Gu
uide
C
Chapte
er 2 Em
2.1 Structure and
a Usagge Instruction of Control
C
P
Panel
I.
Structuree of Controll Panel
1. Touchiing Panel
It addopts high-luminance LCD disp
player and touching sscreen man
n-machine
interactionn interface.
2. Buttonns
Presss the keys too start the em
mbroidery, pause the em
mbroidery.
3. Main USB
U Port
USB disk can bee plugged foor data inpu
ut/output.
II. Instructioons on Toucching Panell
nput devicee. In order tto extend th
he service
Thhis machinee uses the touching paanel as its in
life of the
t panel annd to maintaain its perfoormance, pllease don’t apply too m
much pressu
ure on the
screen during
d
operaation. Neithher can userr use the shaarp or hard tools
t
to clicck the screen
n.
IIII. Instructioons on USB
B Disk
Pleease pay cllose attentioon to electrrostatic pheenomenon. Don’t forgget to disch
harge (we
suggest you shouldd touch the machine sttand or fram
me to dischharge the staatic) before plugging
in/out thhe USB diskk.
Payy attention to the direection of thhe USB disk
k at plug-inn. Don’t puull out the USB
U
disk
when syystem loadss data from or write daata to it. If the
t USB diisk is pulledd out or thee power is
Owner’s Manual
M
of BECS- A15 Computerized Controll System
7
C
Chapter
2
Emb
broidery Guide
G
cut off during
d
the data input/ooutput, the data could
d be lost. In
I that casee, please ch
heck the
integrity of data in thhe USB disk and repairr it before using.
u
Atteention: Duriing the proccess of initialization, if
i the powerr is cut off or the USB
B disk is
pulled ouut, the USB disk may be
b damaged permanentlly.
2.2 Insstruction of the Main
M
Interrface
No.
Icon
N
Name
Networrk
Connecction
Failuree
Status
1
8
Cyclic
Embroiidery
Description
Network
Status
, con
nnected
registratio
on
Refereence Page
(disconnected
, successsful
)
Cyclic embroidery is currenntly
available. Press usser parameeter
or
o specialiist parameeter
to
o enter thhe parameeter
setting in
nterface, whhere user ccan
change the
t
settingg of cycclic
embroiderry.
This figurre will apppear when the
Threadd Breakage machine stops due
d
to the
thread-breeakage.
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
r2
No.
2
Icon
N
Name
Patterrn
Management
Param
meter
Settinng
Color-changing
Orderr Setting
Main Interface
3
4
Emb
broidery Guide
Descripttion
Refeerence Page
Interfacee for patternn managemeent
Interfacee for parameeter setting
Interfacee for color-changing oorder
setting
Main inteerface
Patterrn Displayy
Area
Basic
Patternn
Data
Clear
X/Y
Y
Displaacement
The patteern for embbroidery willl be
displayed
d in this areea.
Basic daata of the current patttern
will be displayed
d
heere.
Clear th
he current value of X/Y
displacem
ment
After maachine stop,, user can cclick
Manuual
this key
y for the operationn of
Threaad-trimmingg manual thread-trimm
t
ming (includding
bobbin th
hread trimm
ming).
op, if the main
m
shaft iss not
After sto
Main
Shaftt
at the pro
oper positioon
,
Manuual
press thiis key to adjust
a
the m
main
Adjusstment
Section
S
2.3
Section
S
2.3
shaft to the
t right possition
5
Framee Selectionn
Frame seelection andd position
and Poosition
If the machine
m
iss set at A
Auto
Color-ch
hanging, usser should set
the color-changinng order in
advance.
t start keyy for
When usser presses the
embroideery, no maatter where the
Auto
current needle rodd locates, the
Color-changing, machine will channge the neeedle
Auto Start
according to the set color-changging
d perform thhe embroideery.
order and
When
encounteering
color-chaanging code, the machhine
will stop
p automaticaally and shiift to
the po
ointed neeedle posiition
according
to
the
auto
Owner’s Manual
M
of BECS- A15 Computerized Controll System
9
C
Chapter
2
No.
Icon
N
Name
Emb
broidery Guide
G
Description
Refereence Page
color-chan
nging ordder. If the
machine is set at auto
a
start, the
machine will
w begin thhe embroideery
automatically; if it is set at mannual
start, the user needss to press the
start key for
f embroidery.
In this status, selecct the needle
with
position
mannual
color-chan
nging (
Manuaal
Color-cchanging,
Manuaal Start
) to sellect
the needlee position and
a then prress
start key for
f embroierry.
encounteriing
When
color-chan
nging code, the machhine
will stop
p automaatically. Iccon
appears, andd the systtem
awaits thee manual ccolor-changiing
At this moment,
m
u
user
needs to
perform manual color-changi
c
ing
5
(
) to shift too the needded
needle position, and press the sttart
key for em
mbroidery
Return
6
Return to the previouus interface
For settting the main shhaft
Main
Shaft
acceleratio
on/deceleraation.
Whhen
Acceleration,
the main
n shaft reaches the
Main
Shaft
highest/lowest speed, this key w
will
Deceleration
be unavaillable.
Used to move thhe frame to
Idling
appointed
d
positioon
withoout
embroiderry
When thee machine is in Reaady
Status, user can carry oout
preparatio
on
workk
of
the
embroiderry, such as patteern
Embroiidery
Ready
Status, selection, setting scaale parametter,
m
the setting reepetition paarameters aand
Confirm
so on. Cllick this keey to confirrm,
Embroiidery
and the machine
m
w turn froom
will
Embroidery
Reaady
Staatus
into
10
Embroideery
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
r2
No.
Icon
N
Name
Emb
broidery Guide
Descripttion
Refeerence Page
Confirmaation Statuss
.
Currently
y, the macchine is unnder
Embroid
dery Confirrmation Staatus,
and userr can start embroideryy at
any time. When the machine sttops,
Embrooidery
user can click this key
k and confirm
Confirrmation
ncelling of Embroiddery
the can
Statuss, Cancell Confirmaation Stattus. And the
machine will returnn to Embroiddery
the Em
mbroidery
ffrom
Ready Status
dery Confirrmation Sttatus
Embroid
6
.
Press it to enter thhe interfacee for
other fun
nction operrations, suchh as
statistic inquiry, frame orrigin
Other Functionn setting, power-off recovery, soft
n
settinng,
machhine
limitation
Operaations
authority
y manageement, toouch
screen calibrationn, and ttime
managem
ment.
When machine
m
stoops at corrrect
position
, thhe operationn is
valid; press it to enter mannual
color-chaanging intterface, whhere
user caan click correspondding
needle position
p
nuumber to m
make
color-chaanging.
This figu
ure is for thhe actual neeedle
Currennt Needlee
position at presentt. 0 is for the
Position
invalid needle
n
positiion.
The initial value is
i 1. After the
Currennt
embroideery starts, this value will
Color-changing
add 1 att each finishh of successsful
Timess
color-chaanging.
This ord
der is the sequence off the
Color-changing
needle rods
r
for changing
c
coolor.
Orderr
The 3D figure is for
f the currrent
osition.
needle po
Scale up
p pattern in the patttern
a
Hold pressing foor 2s
Scale Up Pattern display area.
to shift to
o
.
Manuual
Color-changing
7
Owner’s Manual
M
of BECS- A15 Computerized Controll System
Chapter 9
Section
S
2.3
11
Chapter 2
No.
Icon
Manual
Frame-moving
8
No.
Name
Icon
Name
9
Pattern List
10
Previous/Next
Page
,
Memory Pattern
Preview
Letter Pattern
11
Embroidery Guide
Description
Reference Page
The frame will move along with
the direction keys.
Description
Reference Page
Display patterns by figures for
users to select
Display patterns in different pages
Used to check pattern details, scale
up/down pattern, move or make
analog display of pattern
Letter pattern and its parameter
setting
Pattern Deletion
Used to delete selected patterns
Pattern Output
Used to transfer memory patterns to
USB disk
Home
U Disk
Management
11
12
Other Functions
Press it to enter the U disk
management
interface
for
operations related to U disk.
Used to open other operation
interfaces for memory patterns,
such as pattern copy, deletion,
Owner ’s Manual of BECS- A15 Computerized Control System
C
Chapter
r2
No.
No.
12
Icon
Icon
Naame
Emb
broidery Guide
Descriptioon
Single/M
Multiple
Selectionn
combination, edit, etc.
Shift betweeen single seelection moode
and multiplle selection mode
Next
Enter the neext operatioon interface
Naame
Commoon
Parametter
Setting
Pattern Preview
Description
Refeerence Page
Reference Page
User can adjust
a
these parameterss to
control thee final embbroidery efffect
of the patteern.
Load the selected paattern, dispplay
the pattern
n data and draw up the
pattern shaape.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
13
Chapter 2
No.
Icon
Embroidery Guide
Name
Description
Reference Page
Current Operation
Position
Color
Lump
Number List
Set, insert or delete needle bar number
here.
Display the color lump number of the
pattern
Display the needle bar number and
Needle
Bar
needle bar thread color of the
Number and Color
corresponding color lump
Move up the color-changing list in order to
select the color lump to be set
Move Up
13
Press this key and then press needle bar
Insert Needle Bar
number to insert it to the current needle
Number
bar number list
Delete Needle Bar Delete the current needle bar number
Number
from the needle bar number list
Move down the color-changing list in
order to select the color lump to be set
Move Down
Needle
Bar
Select the color for the selected needle
Number
Color
bar number
Selection Area
14
14
Repetition
Repeat the color-changing order
Patch Embroidery
Set as patch embroidery pattern
Owner ’s Manual of BECS- A15 Computerized Control System
C
Chapter
r2
No.
Icon
Emb
broidery Guide
Nam
me
Descripttion
Reeference Paage
Needle Baar Color Set the neeeble bar coolor from ddefault
Setting
ccolors
2.3 Baasic Procedure off Embroid
dery
Thhe machine carries ouut embroiddery based on the paatterns saveed in mem
mory. The
followinng figure is the basic prrocedure off the embroiidery:
Input Pattern
ns
Select Patterrn
Asssistant Operattions
Confirm Embro
oidery
S
Start
Embroid
dery
Cancel Em
mbroidery
Manuall Operation
I. Input Pattterns
Usser can inpuut patternsss through network
n
or USB diskk. Only witth
(ssuccessful
registrattion) displaayed, can it be possiible to tran
nsmit patteernss by neetwork. For U disk
operatioon, in pattern managgement inteerface, presss
to enter U disk man
nagement
interface.
II. Select Patttern
In patttern managgement interrface, user can
c select needed
n
patteern for embrroidery.
IIII. Assistan
nt Operations
Affter selectingg the patternn for embrooidery, user can make assistant
a
opeerations acccording to
need before
b
embrooidery.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
15
C
Chapter
2
1.
Emb
broidery Guide
G
Set reppetition, rotaation and sccaling —— press
to enter paarameter
maanagement interface.
2.
—
press
Set coolor-changinng orde ——
to ennter color-cchanging
settting interfacce.
3.
Set pattch embroiddery —— press
p
t enter collor-changing
to
g setting
inteerface and set
s patch em
mbroidery of the pattern
n accordingg to hints.
4.
For boorder inquirry, border idling, patttern outlinee —— press
to enter
me selection and positiion operatioon.
fram
5.
Locate pattern at frame centter —— preess to enterr frame selection and position
opeeration. Pleease note thhis functionn is to locatte pattern at
a the framee center sett by soft
lim
mitation.
6.
Set cycclic embroiidery —— press
Preess
to enter other function op
peration.
to enter parameter managemeent interfacce. Then ppress “Emb
broidery
Assistant Paraameters” andd set cyclic embroidery
y according to hints.
IV. Confirm Embroider
E
ry
1. After
A
assisttant operatioons, press
seleect
to confiirm and tuurn
to display a hint winddow, where user can
(canceel embrodeery) to
(coonfirm embbroidery), which
w
indiccates the machine
m
haas entered E
y Ready
Embroidery
Staatus.
If user
u selects
, thhe machine will stay att Embroiderry Cancel S
Status. At th
his time,
thee machine will
w not woork even when user prresses the start
s
key. A hint wind
dow will
display on the screen for user
u to conffirm the em
mbroidery.
2. Set Color-cchanging and Start Modde
Useer can shiftt between
(autoo color-chan
nging and auto
a
start) aand
(manual
collor-changingg and manuual start).
16
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
r2
Emb
broidery Guide
V. Manual Operation
O
1
1.
Manuual Thread-trrimming:
W
When
the machine
m
stoops, press
in the
t main innterface to display a
hint window,
w
wheere user cann press “Trim Upper&B
Bobbin Thrread” to trim
m threads,
or clicck “Trim Boobbin Threaad” to trim the bobbinn thread onlyy. Press
to
quit thhe thread-triimming opeeration.
2
2.
Manuual Frame-M
Moving:
Wheen the machhine stops, press direcction keys (
,
,
,
)
to move frame alonng the correesponding direction.
d
Prress the twoo neighborin
ng keys at
the samee time to move
m
the fraame in the direction off the angle bisector.
the speeed key for manual frrame-movin
ng. Press too shift betw
ween
speed) and
a
3
3.
is
(high
(low speeed).
Clear the Frame Coordinates
C
s
Wheen the machhine stops, press
to clear thhe XY dispplacements displayed
in the maiin interface. The functiion can be used
u
with manual
m
framee-moving.
4
4.
Manuual Color-Chhanging
Wheen the macchine stops, press
in the main interfface to enteer manual
color-channging interface. Then click the needle
n
numbber for coloor-changing
g, and the
machine head
h
will auutomaticallyy move to th
he corresponnding needlle position.
Pleaase note: iff the user wants
w
to au
utomaticallyy save the oorder of th
he manual
color-channging, userr should opeerate it in th
he manual color-changging interfaace on the
Owner’s Manual
M
of BECS- A15 Computerized Controll System
17
C
Chapter
2
Emb
broidery Guide
G
touch screeen.
5.
Adjust Main Shaftt Manually
Usuallly, the maain shaft needs
n
to stop
s
at 1000° at neeedle/color-ch
hanging,
frame-movving and beeginning em
mbroidery. User
U
can manually
m
turnn the main shaft to
100° whenn it hasn’t reached
r
theere. Press
in thhe main intterface to carry
c
out
this functioon.
After the operaation,
w changiing into
(not in position) will
(in
position).
6.
Back too Origin
i the mainn interface to
in
t enter idlling interface, where user
u
can
Press
press
7.
to retuurn the fram
me to origin..
Back too Stop Poinnt
Press
press
8.
u
can
in the mainn interface to enter iddling interfaace, where user
to retturn the fram
me to stop point.
p
Positiooned Idling
Use this function affter embroiidery confi
firmation. Positioned
P
idling enab
bles the
machine too move to the appointted position
n without embroiderin
e
ng accordin
ng to the
user’s reqquests. Preess
to set idling baackward oor forward at the
color-channging code or
o stop codee by one stittch or continnuously.
VI. Cancel Em
mbroidery
W
When
the machine
m
stopps, press
seelect
to turrn
to
o display a hint windoow, where user
u
can
(embroid
dery confirrmation) to
(cancel
em
mbroidery confirmatio
c
on).
18
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
r2
Emb
broidery Guide
2.4 Noormal Em
mbroiderry, Returrning and
d Patchin
ng
In embroideryy confirmattion status (
is displayeed), press
embroiddery, and duuring embrooidery, presss
to start normal
to stop
s
embroiidery.
Whhen the macchine stops,, press
to reeturn the fraame back aloong with th
he original
embroidery path; one press, one stitch back;
b
hold pressing
p
forr 2s to returrn continuou
usly, even
withouut holding
; press
p
again to
t stop.
The purpose of
o returning is for patchhing, and wh
hen the macchine stops rreturning, prress
to start normal
n
embrroidery.
2.5 Em
mbroiderry Operaation
Whhen the macchine stops, press
to start em
mbroidery;
Whhen the macchine is embbroidering, press
to stop em
mbroidery.
2.6 Th
hread-Brreakage Detection
D
n
B
Based
on diifferent woorking princciples, threaad-breakagee detection devices have three
types: thhread take-uup spring tyype, thread winding
w
wh
heel (choppeer wheel) tyype and mix
xed type.
For thread taake-up sprinng type, it detects
d
the th
hread-breakkage by seaarching conn
nection of
take-up spring and contact poiint. When thhread break
ks, the springg will closee to the conttact point.
In norm
mal condition, this deteccting type is
i sensitive to the face thread breaakage, but can
c hardly
detect bobbin
b
threead run-out.. In case you
y change the embroidery threaad, or threaad tension
Owner’s Manual
M
of BECS- A15 Computerized Controll System
19
C
Chapter
2
Emb
broidery Guide
G
changes, you need to adjust spring
s
presssure betweeen the takee-up spring and contacct point.
When the spring preessure is tooo large, theere will be False Alarm
m; when thee spring preessure is
too smalll, there will be Missingg Alarm.
For thhread windding wheel type,
t
it judgges thread-b
breakage byy detecting the windin
ng wheel
angle. It is very seensitive in case
c
of facce thread brreakage; inn most casees of bobbin
n thread
run-out, the consum
mption of faace thread will
w reduce, as a result,, system wiill judge by statistic
method and
a send ouut warning. Though it can
c almost avoid Falsee Positive, iit is not as sensitive
s
as the sprring-type.
For the
t mixed type
t
method, the two can compllement eachh other witth their adv
vantages,
which results in senssitive and sttabilized deetecting effeect.
2.7 Woorking Sttatus
Theere are threee working sttatuses:
1. Embroideryy Ready Status
S
preset paarameters, cchoose emb
broidery
pattterns and make
m
other preparation
p
work for em
mbroidery.
2. Embroideryy Confirmaation status
conffirm the paarameter setttings to
entter the quasii-running sttatus.
3. Embroideryy Running Status
S
em
mbroidery.
Shifft among theese three woorking statuuses:
is displaayed in the main interfface), if useers have
In embroidery
e
ready statuus (
selected pattern andd related parrameters, prress
and theen press
and the system
s
willl enter embrroidery connfirmation status
s
(
to confirm,
is dissplayed in the
t main
interface). At this time, presss start keyy to start embroidery,
e
when the machine is
i under
embroideery running status (
is displlayed in the main interfface).
In embroidery running
r
stattus (
20
is displayeed in the maain interfacee), press sto
op key to
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
r2
Emb
broidery Guide
stop em
mbroidery annd return too embroiderry confirmaation status,, where useer can press start key
again too enter embrroidery runnning status.
In embroideryy confirmattion status (
and thenn press
return too embroiderry ready staatus (
is displayeed in the m
main interfacce), press
to confirm,
c
useer can releaase the connfirmation status
s
and
is displayed in the main interfface).
Owner’s Manual
M
of BECS- A15 Computerized Controll System
21
Chapter 3
U Disk Management
Chapter 3 U Disk Management
In U disk management interface, user can input patternss from U disk to machine, and
vise versa; meanwhile, user can undertake some common U disk managements, like erasing
file or directory, initializing the disk, etc. User can save patterns data under different directories
of the U disk based on different types. Patterns formats like DSB, DST and DSZ can be read by
the system. For data output, patterns will be saved in the U disk as DSB format.
3.1 Select U Disk
Since the system supports several storage devices, user need select the U disk for operation.
1.
Press
in pattern management interface.
2.
System will display “Select U Disk” window, where user need select U disk by
pressing corresponding icon.
In this window all the storage devices will be displayed. Their information includes the
icon, words and numbers. The icon is the device type.
Icon
indicates U disk. The
words are the label of the U disk (if the U disk has no label, the default letter will be used), and
the number refers to the U disk’s digital symbol.
22
Owner ’s Manual of BECS- A15 Computerized Control System
C
Chapter
3
3
3.
No.
1
2
3
4
U Dissk Mana
agement
Enter U disk operation interfface.
Icon
Nam
me
Deescription
Display the pattern
D
p
filess and file foolders within
n the U
d in iconss. It’s used to select filees.
disk
File Listt
Page
The current page
T
p
numbeer and total page numb
ber
Informaation
Back too Upper
R
Return
to up
pper level
Level
Basic Pattern
D
Display
the basic
b
data of
o current paattern
Data
L
Load
the seelected patttern. Checkk its detailss, scale
Pattern
u
up/down
thee pattern, and move or make analog
Preview
w
d
display
of th
he pattern.
Create
C
Create
new file
f folder
Directorry
Deletionn
Formattting
Disk
D
Delete
the file or file follder
U
F
Formatting
the
t U disk
Pattern Input
I
Im
mport the patterns in thhe U disk too memory.
Exit
E U disk managemen
Exit
m
nt.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
23
Chapter 3
U Disk Management
3.2 Pattern Preview
1.
In the U disk management interface, press the pattern for preview.
Pattern files and directories are shown in figure in the list. One page of the list contains 8
items. If the amount of the object within the current directory is more than 8, the object list will
be displayed in many pages. Click the key to turn page and look for patternss in another page.
The selected object has a different frame and background color.
2.
24
Press
Owner ’s Manual of BECS- A15 Computerized Control System
C
Chapter
3
U Dissk Mana
agement
Thhe system looads the daata from thhe U disk and
a user caan check deetails of the pattern,
scaleupp/down the pattern, moove or make analog display of thee pattern. Foor more infformation,
please refer to secction 6.3.
3.3 Paattern Inp
put
To input patteerns within the U disk to the mach
hine’s memory, user neeed select th
he pattern
files to be inputteed, and thenn input thee number and
a name for
f the pattterns to be saved in
memoryy.
1.
Selectt pattern filees of the U disk;
2
2.
Press
3
3.
Input the pattern number andd name to be
b saved in memory;
m
annd the system
m will requ
uire input off pattern num
mber and naame;
Owner’s Manual
M
of BECS- A15 Computerized Controll System
25
Ch
hapter 3
U Disk
k Manag
gement
Thee system proovides the minimum
m
avvailable patttern numberr as the defaault value. User
U can
use the keypad beloow to changge the numbber.
4..
Press
too confirm;
5..
The sysstem will saave the patteern data fro
om the U dissk to the meemory.
3.4 Dirrectory Operation
O
n
1..
Enter directory:
d
Douuble click thhe icon of thhe object diirectory to enter
e
it, andd the system
m will load the item
list of thee directory and
a refresh the displayy interface.
2..
Return to Upper Level:
L
Presss
to return to
t the upperr level of diirectory andd refresh thee display intterface.
3.5 Forrmatting U Disk
1..
Select the
t U disk for
f formattinng;
2..
Press
3..
Press
to start
s
formattting;
too confirm
Systtem will beegin to form
mat the dissk and retu
urn automattically to U disk management
interface after finishhing formattting.
Note: system will
w format the
t U disk according
a
to
o DOS form
mat.
26
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
3
U Dissk Mana
agement
3.6 Deelete Objjects from
m U Disk
k (including patterrn file an
nd directo
ory)
1.
Selectt objects to be deleted;
2
2.
Press
3
3.
System
m will ask user
u to conffirm the deleetion.
to delete;
Noote:
If the user wants
w
to delete
d
a directory,
d
th
he system will deletee all the files and
sub-direectories withhin this direectory. In case of “Reaad Only” orr “U Disk W
Write Protecction”, the
file willl be unable to
t delete.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
27
Ch
hapter 3
U Disk
k Manag
gement
3.7 Creeate a Neew Directtory in th
he Current Directtory
1..
Press
2..
Input thhe new direectory namee
3..
Press
Systtem will creeate the corrresponding directory in
n the U diskk and refressh the curren
nt object
list.
28
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chapteer 4
Ch
hapter 4
Coommon Paramete
P
rs and Color-Ch
C
hanging Order
O
Com
mmon Paarameterrs and Color-Ch
C
hanging Order
O
Inn this system
m each patttern has its own setting
gs of the noormal param
meters (like scale and
repetition) and color-changiing order. When
W
a neew pattern is selectedd, the correesponding
settinggs of normall parameterss and color--changing order
o
will beecome effecctive.
Inn this chaptter, we willl discuss the setting off the most frequently
f
uused param
meters and
color-cchanging order,
o
in parameter
p
s
setting
inteerface (
color-cchanging orrder setting interface (
) and neeedle bar
).
Since this syystem suppports multi--task operattion, user can
c set andd modify th
he normal
n embroiddered at pressent. User
parameeters and coolor-changinng order of the patternsss that are not
can ennter these operations via other operation interface
i
unnder patterrn managem
ment (see
Chapteer 6).
4.1 Settings of Commoon Param
meters
T
These
comm
mon parameters includee: “Directio
on”, “Anglee”, “Scale X
X/Y”, “Prio
or Mode”,
“Rep. Mode”, “R
Rep. Order”, “Rep. Tim
mes”, and “Rep.
“
Intervval”. User ccan controll the final
embroidery resultts by adjustiing these paarameters.
Prress
t enter paraameter settiing interfacee:
to
Owner’s Manual of BEC
CS- A15 Compputerized Controol System
29
Chapter 4
Common Parameters and Color-Changing Order
The way for setting the parameter is similar to each other. This chapter will explain how
to set the “X/Y Scale” as an example and give the definitions of other parameters (refer to
4.1.1 for setting method).
4.1.1. Settings of X-Y Scale
This parameter controls the scaling percentages on X (horizontal) and Y (vertical)
direction, so as to scale up/down the patterns.
X&Y Scales:
X : 2 0 0 %
Y : 5 0 %
Desig n sta rt b it
De sig n sta rt b it
1.
30
Press the function item of “Scale X/Y”
Owner ’s Manual of BECS- A15 Computerized Control System
Chapteer 4
Coommon Paramete
P
rs and Color-Ch
C
hanging Order
O
Syystem will display
d
indeependently the modificcation windoows for X S
Scale and Y Scale for
users to
t set respecctively.
2.
Adjuusting X-Y Scales
S
U can preess number pad to moddify the scaaling rate att X directioon, press
User
cancel the last inpput digit andd press
3.
Presss
to
to cleear the inputt number.
to save thee modificatiion
The modiffication metthod of Y Sccale is the same
s
with thhat of X Scaale.
4.1.2.. Settingss of Rota
ate Anglle
U can rottate patternss to a certainn angle by this
User
t parametter.
Owner’s Manual of BEC
CS- A15 Compputerized Controol System
31
Chapter 4
Common Parameters and Color-Changing Order
Rota te 30 d eg re e s
Desig n sta rt b it
4.1.3. Pattern Direction
4.1.4. Prior Mode
There are two modes: “rotation prior to scaling” and “scaling prior to rotation”. When
user has set the parameters “Scale X/Y” and “Rotate Angle”, the patterns will rotate first and
then scale up/down, if “rotation prior to scaling” mode is selected. Otherwise it will scale
up/down first and then rotate.
4.1.5. Rep. Mode
There are two repetition modes: normal and partial.
4.1.6. Rep. Order
There are two modes: X first and Y first.
32
Owner ’s Manual of BECS- A15 Computerized Control System
Chapteer 4
Coommon Paramete
P
rs and Color-Ch
C
hanging Order
O
4.1.7.. X-Y Re
ep. Times
X repetition times repreesent the num
mber of collumns, whille Y repetitiion times th
he number
of linees; as shownn in the aboove picture,, X repetitio
on times arre 3 and Y rrepetition tiimes is 2.
The larrgest set vallue is 99*999.
4.1.8.. X-Y Re
ep. Intervval
T above piicture has exxplained thee meaning.
The
4.2 Settings of Color-cchangingg Order
4.2.1.. Color-c
changingg Interfaace
Noo.
Iconn
Name
1
Patttern Displayy Area
2
Bassic Pattern Data
D
3
Currrent
Possition
Descriptiion
Display
D
thhe pattern according
g to
real-time setting
s
of color-chan
nging
order,
o
for thhe preview of the resu
ult of
color-changi
c
ing.
Display
D
the basic data oof the patterrn
Opperation User
U can sett, insert or ddelete needlle bar
number
n
in cuurrent posittion.
Owner’s Manual of BEC
CS- A15 Compputerized Controol System
33
Chapter 4
No.
Icon
3
4
5
Common Parameters and Color-Changing Order
Name
Description
Color Lump Number Display the number of the color lumps
List
of the pattern
Display the needle bar number and
Needle Bar Number
thread color of each corresponding
and Color
color lump
Move upward the color-changing list to
Move Up
select the color lump for setting
Insert Needle Bar Click this key and a needle number to
Number
insert it in the current list of needle list.
Delete Needle Bar Delete the needle number of the current
Number
operation position in the needle list.
Move downward the color-changing
Move Down
list to select the color lump for setting
Select the color for the needle bar
Color Selection Area
number to be set
Return
Return to
interface
Repetition
Repeat color-changing order
Patch Embroidery
Set the patch embroidery of the pattern
Set Needle Bar Color
Pattern Preview
Next
the
previous
operation
Select default colors to set the color of
each needle bar
Load the selected pattern, check the
pattern data and create the pattern icon
Enter the next operation iterface
The pattern display area displays the pattern under color-changing setting. After
changing the color-changing order, the display will be renewed at same time to show the
modification effect.
Color-changing order display area shows color lump numbers, needle bar numbers and
needle bar colors.
Pattern display can be in parallel with the setting, insertion and deletion of needle bar
number, which means that users can set and change the color-changing order along with the
display.
34
Owner ’s Manual of BECS- A15 Computerized Control System
Chapteer 4
Coommon Paramete
P
rs and Color-Ch
C
hanging Order
O
4.2.2.. Settingss of Colo
or-Changing Ord
der
1.
Presss
to ennter color-ch
hanging settting interfacce.
2.
Inpuut the needlee bar numbbers in ordeer in the neeedle bar nuumber selecction area.
T patternn display andd the color list
The
l will be refreshed
r
affter each inpput.
3.
Presss
to check wh
hether the innputted collor-changing
g order is
c
correct.
4.
To chhange a cerrtain needlee bar numbeer, press
to mo
ove to the
i
item
to be modified
m
and then presss the new neeedle bar nuumber.
5.
To innsert a new
w needle bar number, press
p
positon
bellow the poosition to be
b inserted,, and then
to mov
ve to the
to innsert the neeedle bar
n
number.
6.
Presss
to delete a neeedle bar num
mber.
4.2.3.. Set Nee
edle Bar Color
To make thee display effect close to the actu
ual embroiddery effect,, this systeem allows
settinggs of color for each needle
n
bar and such settings caan be saved together with the
color-cchanging orrder of the pattern.
p
1.
Presss
2.
Presss
to enter
e
color-cchanging seetting interfaace.
to enter neeedle bar color setting interface.
i
Owner’s Manual of BEC
CS- A15 Compputerized Controol System
35
C
Chapter
4
Com
mmon Parrameterss and Color-Changing Order
45 default coloors for selecction in the setting interface
3..
To set the needle bar color, select
s
the needle
n
bar first
f
and theen select th
he color
froom the 45 default
d
colorr lumps. Thhe correspon
nding color of the needdle bar buttton will
be refreshed.
4..
Press
too save the settings and
a
return to the coloor-changing
g order
settting interfa
face; or preess
to quit setting wiithout savinng and retturn to
collor-changinng order settting interfacce.
36
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
r5
Settiings of Embroide
E
ery Paraameters
Ch
hapterr 5 Setttings of Embrroidery Parameeters
Parameters are
a grouped according to
t different functions (ssee Appenddix 1 Parameeter List)
Prress
in thee main inteerface and press
(for user) or
(for
speciallist) to enterr parameterr setting inteerface.
1.
Afterr system ennters parameeter setting interface, user
u can seleect the paraameter for
s
setting.
Owner’s Manual of BEC
CS- A15 Compputerized Controol System
37
Ch
hapter 5
Settings of Em
mbroiderry Param
meters
Note: the num
mber, name and current value of each parrameter are displayed in the
parameteer list windoow.
5.1 Proocedure for
f Settin
ng Generral Param
meters
Thee setting proocedure is siimilar for each
e
generall parameterr. You can fo
follow the guide
g
of
this section to set alll parameterss.
1..
Select Parameter
P
T
Type
Useer can use the
t keys at the
t bottom of the screeen (parametter type keyy and page key) to
look for the
t parametter.
If you
y want too modify thhe number of needles whose paraameter num
mber is D01
1, press
to find machiine configurration param
meter and th
he its param
meter list willl be display
yed.
2..
38
Press thhe parameteer to be set and
a input th
he new valuue by the nuumber keys.
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
r5
3.
Presss
Settiings of Embroide
E
ery Paraameters
to finish thhe setting.
5.2 In
nstructioon on Som
me Functtions with
hin Geneeral Paraameters
There are brrief descriptions of paarameters in
T
n the appenndix 1. Heree, we will introduce
some functions
f
m
mainly
used in
i embroideery.
5.2.1.. Cyclic Embroid
E
dery Fun
nction
T functioon is to increease the emb
This
mbroidery prroductivity.
W
When
the parameter
p
“
“To
Do Cyyclic Emb.”” is set as “Yes”, thee cyclic em
mbroidery
functioon is activatted and the icon
will appeear in the main
m
interfacce. If this fu
unction is
activatted, the machine will automaticallly embroid
der the patteernsated paatterns again
n without
any opperation wheen completiing it.
U
Usually,
cycllic embroiddery should accompany
y repetition embroideryy and speciaally made
patternns, and thee parameterr “Auto Orrigin” should be also set as “Yees”. Thus when
w
the
machinne is embrooidering thee back fabriic, the frontt one can be
b replaced.. After emb
broidering
the pattternsated patterns, the frame will automatically return too the start pooint and thee machine
will auutomaticallyy embroiderr the front fabric again
n and at thhis time it’s possible fo
or user to
replacee the back one.
o
5.2.2.. Brake Adjustm
A
ment (A Must
M
for New Maachine)
T functioon is to adjuust the conttrol parametters for brakking, so as to fit mach
This
hines with
differeent mechaniical characteers, which is
i also able to change with
w the maachine runn
ning. Thus
this fuunction can help the machinery
m
p
parts
to worrk better with
w the com
mputer. Thee function
dependds on the paarameters “S
Set Brake Para”.
P
“S
Set Brake Para”
P
is to adjust the stop
s
positio
on of the main
m
shaft. W
When the main
m
shaft
often stops
s
at the position beelow 100 deegree, the usser can increase the parrameter value. When
the maain shaft oftten stops at the positionn over 100 degree,
d
the user can deecrease the parameter
p
value. Thus the user
u can adjust the valuue to let thee main shafft stop closee to 100 degree. The
value can
c be set between
b
0 annd 30.
A
After
adjustinng this paraameter, the user
u can cliick the task swift key oon the panell to return
to the main interrface. Clickk
a
and
to make the adjustm
ment and check
c
the
effectss of the paraameter adjuustment. If the
t user is not satisfieed with the effects, he can press
the sw
wift key on the
t panel to return to thhe parameteer setting innterface, whhere he can adjust the
parameeter setting again. Closse the param
meter setting
g interface in
i the end.
Owner’s Manual of BEC
CS- A15 Compputerized Controol System
39
Chapter 6
Memory Pattern Management
Chapter 6 Memory Pattern Management
Memory pattern management includes selection of embroidery patterns, settings of
patterns, change of patterns and operations for creating patterns.
6.1 Memory Pattern Management Interface and Other Memory
Pattern Operation Interfaces
Press
to enter memory pattern management interface.
The memory patterns management interface contains: patterns image display area,
navigation and pagination area, information area and management operation area. The patterns
image display area can show 8 patternss at most. If the total number of the patterns is beyond 8,
more pages will be needed. Navigation and pagination area can help switch to the patternsated
page. The management operation area is to preview patternss and set their order.
No.
1
40
Icon
Name
Description
Pattern Display Area
Display the pattern files in memory
by icons. It’s mainly for selection.
Owner ’s Manual of BECS- A15 Computerized Control System
Chaptter 6
Noo.
2
3
Icoon
,
M
Memory
Pattern
P
M
Managem
ment
Nam
me
Prrevious/Nexxt Page
Innformation Area
A
Paattern Previeew
Leetter Patternn
4
Used to shift to aappointed page
number
Display thhe detailed informatio
on of
the selecteed pattern aand the mem
mory
informationn.
Check the details of thhe pattern; scale
up/down, move orr simulate the
pattern.
Set letterr embroiddery and its
parameterss
Deelete Patternn
Delete the selected paattern
Paattern Outpuut
Save the memory
m
patttern to U dissk
Hoome
Siingle/Multipple
Seelection Shiift
Press it to enter U diisk manageement
interface too make relatted operatio
ons.
Click to open the other operration
interface, where useer can perrform
copy, deleetion, combbination, ed
dition
and other operations.
o
Shift betw
ween singlee selection and
multiple seelections.
Neext
Enter the next
n operatioon interfacee
U Disk Manaagement
Otther Operations
Preess
Descriptiion
to enter thhe interface for other operations
o
o memory ppattern (to deal with
of
any singgle pattern, user need select
s
the paattern first).
Owner’s Manual
M
of BECS- A15 Computerized Controll System
41
Chapteer 6
Meemory Pa
attern Managem
M
ment
In thhis interfacee, press eacch operationn to enter th
he corresponnding interfa
face. Please read the
followingg paragraphhs for detailed explanaation. Press
or
to tuurn page, an
nd press
to return too memory pattern
p
mannagement interface.
6.2 Select Patteern for Em
mbroiderry
to enterr memory pattern manaagement intterface.
1..
Press
2..
Select the
t pattern in
i the memory pattern image display area.
6.3 Meemory Paattern Preview
Thee selected paattern can be
b previeweed in the memory
m
patteern preview
w interface to
t check
more deetails.
42
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaptter 6
No..
1
Iconn
M
Memory
Pattern
P
M
Managem
ment
Name
Pattern
Areaa
Descriptionn
Previeew Displaay the patteern in the aappointed method
m
and sp
peed
Draw
w/Pause
Switch
Shhift betweenn drawing pattern
p
and paausing display
Movve up
Singgle
Dispplay
2
Move the pattern upwards
Sttep
Draw the
t pattern by
b drawingg single step
ps
Scalle up
Enlarg
ge the patterrn in the preeview area
Scalle down
Reducce the patterrn in the preeview area
Actuual Display
Displaay the patteern in the aactual size. So the
size off the patternn on the sccreen is the actual
size off the patternn after embrroidery.
Dispplay to tthe
Displaay the patterrn accordintt to the sizee of the
Sizee
of
t
the
pattern
n preview arrea.
Winndow
Movve left
Move the pattern leftward
Owner’s Manual
M
of BECS- A15 Computerized Controll System
43
Chapteer 6
No.
Icon
2
Meemory Pa
attern Managem
M
ment
Name
D
Description
Movee down
Move th
he pattern downward
d
Movee right
Move th
he pattern riightward
Deceleration
Lower the
t display speed of paatterns
Acceleration
Fasten the
t display speed of paatterns
Redraaw
Redispllay the seleccted patternn
Quit
Quit thee operation in pattern ppreview inteerface
1..
Press
2..
Select a pattern in the memorry pattern im
mage displayy area.
3..
Press
4..
Press
Preess
to enterr memory pattern manaagement intterface.
to open
o
memorry pattern preview interrface.
to control thee size of tthe pattern display.
to contrrol the dissplay position. Press
to coontrol displaay speed. Press
P
to shift to
t the pausse status, where
w
the
sinngle step of pattern can be displayeed. Press
to reedisplay thee selected paattern.
6.4 Patttern Outtput
Useer can transffer the pattern data in memory
m
to U disk.
44
1..
Press
to enterr memory pattern manaagement intterface
2..
Select the
t memoryy patterns too be outputtted
3..
Press
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaptter 6
M
Memory
Pattern
P
M
Managem
ment
44.
System
m will dispplay the window
w
to “Select U disk” and press to make
m
the
seelection.
4
4.
Input the pattern name savedd in the U disk.
d
Thhe system prrovides the minimum available
a
paattern numbeer as the deefault value. User can
use the keypad beloow to changge the numbber.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
45
Chapteer 6
5..
Press
6.
Press
Meemory Pa
attern Managem
M
ment
of the complletion hint.
r
to paattern manag
gement interface.
to return
6.5 Cop
py the Memory
M
P
Pattern
to enterr memory pattern manaagement intterface.
1..
Press
2..
Select a pattern in the memorry pattern im
mage displayy area.
3..
Press
4..
Click “Copy Paattern” to enter its operation interface. The systeem will
to enter
e
memorry operation
n selection interface.
i
auttomatically provide thee smallest available
a
paattern number and defaault pattern name. If
thee user doesnn’t want to change
c
them
m, please preess
5..
.
To inpuut a new paattern numbber, click “New Patterrn number” and input the new
num
mber in the pop-up winndow.
46
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaptter 6
6
6.
M
Memory
Pattern
P
M
Managem
ment
To chhange the new pattern name, click
k “New Paattern name” and inputt the new
naame in the pop-up
p
winddow.
7
7.
Press
innterface. Prress
to copy thhe pattern and
a
return to pattern operation selection
to cancell the copy operation and
a return to pattern operation
seelection inteerface.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
47
Chapteer 6
Meemory Pa
attern Managem
M
ment
6.6 Creeate Outlline Patteern
Thiis operationn can generaate a new paattern based
d on the outlline of the ddesignated pattern.
p
1..
Press
to enterr memory pattern manaagement intterface.
2..
Select a pattern in the memorry pattern im
mage displayy area.
3..
Press
4..
Press “Create
“
Outlline Patternn” to enter th
he operationn interface.
5..
User caan press to input
i
new pattern
p
numb
ber and nam
me instead oof default on
nes.
6..
Press
to enter
e
memorry operation
n selection interface.
i
too create thhe outline pattern andd return too pattern operation
o
sellection interrface. Presss
t quit the creating opperation annd return to
to
o pattern
opeeration seleection interfface.
6.7 Creeate High
h-speed Pattern
P
Thiss function can
c be usedd to devidee long stitch
h into shortt ones, so aas to preven
nt speed
reductionn due to lonng stitches.
1..
Press
to enterr memory pattern manaagement intterface.
2..
Select a pattern in the memorry pattern im
mage displayy area.
3..
Press
4..
Press “Create
“
Highh-speed Patttern” to entter the operaation interfaace.
5..
User caan press to input
i
new pattern
p
numb
ber and nam
me instead oof default on
nes.
6..
Press
to enter
e
memorry operation
n selection interface.
i
too create thee high-speed pattern and
a return tto pattern operation
o
sellection interrface. Presss
t quit the creating opperation annd return to
to
o pattern
opeeration seleection interfface.
6.8 Divvide Patteern
Thiss operation is to divide one patternn into two new
n patternss.
48
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaptter 6
M
Memory
Pattern
P
M
Managem
ment
1.
Press
to enteer memory pattern mannagement innterface.
2
2.
Selectt a pattern inn the memoory pattern image
i
displaay area.
3
3.
Press
4
4.
Press “Divide Paattern” to ennter the operration interfface.
5
5.
User can
c press too input new pattern num
mber and naame instead of default ones.
o
6
6.
Press “Divide Stiitch” to inpuut the stitch
h number off the divisionn position.
7
7.
Press
to enter memoory operatio
on selectionn interface.
t divide thhe pattern in
to
nto two new
w patterns aand return to
t pattern
opperation sellection interrface. Presss
to quit the dividing
d
opeeration and
d return to
paattern operaation selectiion interfacee.
6.9 Crreate Parrameter Pattern
P
Thhis operationn is to create a new patttern from th
he seleted pattern
p
togetther with th
he settings
of its coommon paraameters andd color-channging order.
1.
Press
to enteer memory pattern mannagement innterface.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
49
Chapteer 6
Meemory Pa
attern Managem
M
ment
2..
Select a pattern in the memorry pattern im
mage displayy area.
3..
Press
4.
“
Paraameter Patteern” to enter the operattion interfacce.
Press “Create
5..
User caan press to input
i
new pattern
p
numb
ber and nam
me instead oof default on
nes.
6..
Press
to enter
e
memorry operation
n selection interface.
i
too create thee parameterr pattern annd return too pattern operation
o
sellection interrface. Presss
t quit the creating opperation annd return to
to
o pattern
opeeration seleection interfface.
6.10 Mosaic
M
Paattern
Thiss operation is to combbine two paatterns into one new paattern. The interval of patterns
refers to the distancee between thhe end of thhe first patteern and the start of the second patttern.
1. Press
to enterr memory pattern manaagement intterface.
2. Select the
t two pattterns to be combined
c
and record thheir pattern numbers.
3. Press
to enter
e
memorry operation
n selection interface.
i
4. Press “Mosaic
“
Patttern” to entter the operaation interfaace.
50
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaptter 6
M
Memory
Pattern
P
M
Managem
ment
5. User can
c press too input new pattern num
mber and naame instead of default ones.
o
6. Press “X Intervall” to input thhe value. Prress “Y Inteerval” to inpput the value.
7. Press
interface. Press
P
to combinee patterns and return to pattern operation selection
to quit thhe combinin
ng operationn and returnn to pattern operation
selection innterface.
6.11 Create
C
Coombined Pattern
Thhe combinedd pattern meeans a patteern group co
ombined froom several ccertain (lesss than 99)
memoryy patterns after setting their parrameters. The
T combinned pattern is set as automatic
a
continuoous embroiidery. To em
mbroider a combined pattern, usser need reeturn to thee memory
pattern managemennt interfacee after creatting or editting the com
mbined patttern, wheree user can
select thhe combinedd pattern, annd then afteer embroidery confirmaation, press start to emb
broider.
1.
Press
to enteer memory pattern mannagement innterface.
2
2.
To eddit existing combined patterns, seelect a com
mbined patteern; to creaate a new
coombined paattern, just follow
fo
the innstructions below.
b
3
3.
Press
to enter memoory operatio
on selectionn interface.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
51
Chapteer 6
4..
Meemory Pa
attern Managem
M
ment
Press “Create
“
Com
mbined Patteern” to enteer the operattion interfacce.
Thee combined ID shows thhe current pattern
p
num
mber and how
w many pattterns the co
ombined
pattern iss composed of. Displayy form is “ppattern numb
ber (the totaal amount of patterns)””.
5..
Set thee parameterrs of the firrst pattern, including pattern num
mber, scalin
ng ratio,
rottating angle, pattern dirrection and priority mo
ode. Please refer
r
to Chaapter 4 for details
d
of
thee settings.
6..
Press
to seet several patterns for packing. And
A press
to go back to
chaange the parrameters off combined patterns.
p
If thhe current pattern
p
is not
n the first of the com
mbined pattern, user neeed set the interval
between it and the fiirst pattern. Please refeer to Chapteer 4 for details of inputtting parameeters.
52
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaptter 6
7
7.
Press
M
Memory
Pattern
P
M
Managem
ment
t enter the operation interface.
to
i
Thhe system will
w hint userr to input the new patteern number and
a the new
w pattern naame.
8
8.
Press
to save thee combined
d pattern and
a
return tto pattern operation
seelection inteerface. Press
t quit savin
to
ng and retuurn to patternn operation
n selection
innterface.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
53
Chapteer 6
Meemory Pa
attern Managem
M
ment
6.12 Saatin Stitcch Adjusttment
Thiss operation is to adjust the satin width in the design
d
accoording to thee need.
1..
Press
to enterr memory pattern manaagement intterface.
2..
Select a pattern in the memorry pattern im
mage displayy area.
3..
Press
4..
Press “Satin
“
Stitchh Adjustmennt” to enter the operatioon interfacee.
5..
User caan press to input
i
new pattern
p
numb
ber and nam
me instead oof default on
nes.
6..
Press “X
“ Adjust Value”
V
and “Y Adjust Value”
Va
to inpput the valuee respectiveely.
7..
Press
to enter
e
memorry operation
n selection interface.
i
too make the satin
s
stitch adjustment and return to pattern operation
o
sellection interrface. Presss
t quit the adjusting operation
to
o
annd return to
o pattern
opeeration seleection interfface.
54
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaapter 7
Letter Pattern
P
O
Operatio
on
Chaapter 7 Letteer Pattern Opeeration
Syystem can generate
g
lettter pattern based
b
on thee built-in fonnt libraries.
7.1 En
nter Main
n Interfaace for Leetter Embroideryy
Prress
in the patttern managgement inteerface to ennter the maiin interface for letter
em
mbroidery.
7.2 In
nput Letteer Stringg for Emb
broidery
Prress
in the main
m
interfface for lettter embroiddery to enteer letter strring input
innterface.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
55
Chap
pter 7
Letter Pattern Operation
O
n
Thee upside of the
t window
w is the displlay area and
d the downsside is the ooperation areea. After
inputtingg the letter string, press
to save.
7.3 Adjjust Lettter Patterrn
1.. Letter Patttern Adjustm
ment Interfface
Theere are 4 row
ws of operattion keys inn the interfacce, the first two rows aare the file and
a view
56
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaapter 7
Letter Pattern
P
O
Operatio
on
functionns keys, thee third row are keys foor adjusting
g letter arrangement, aand the forth
h row are
keys forr adjusting letter
l
string. In the midddle of the in
nterface is the
t letter paattern displaay area.
Geenerally, useer should seet the param
meters, such as whole arrrangement method, rotate angle
and lettter interval of the letteer string; thhen select certain
c
letteer to adjust the its arrangement
parametters.
Letter patten display window: thee crosses in
n the centrre are the coordinatess and the
intersecction repressents the origin
o
(0, 0).
0 The lettter will be
b arrangedd around th
he origin
automattically.
2 Keys forr Adjusting Selected Leetters
2.
“Letterr String”: eddit letter strring.
“Channge Font”: change thee font of seelected letteers. Press tthis key to display a
dialog box,
b where user
u can sellect a desireed font and confirm
c
it.
“Colorr-changing Shift”: set or
o cancel co
olor-changinng before thhe selected letter.
l
“Selecttion Shift”: shift amonng selected letters.
l
A lettter must bee selected before
b
any
edit. Iff a red “
” appears onn a letter, it means
m
the letter
l
is seleected, such aas
. Th
he system
will seelect all lettters as defaault. Press this
t
key to select the first
f
letter, aand press itt again to
select the
t second one, and soo on. After selecting
s
thee last letter, press this kkey again to
o select all
letters..
i
width of seleccted letter.
“Increasse Width”: increase
“Reduce Width”: reeduce widthh of selected
d letter.
“Increasse Height”: increase heeight of seleected letter.
“Reducce Height”: reduce heigght of selectted letter.
“Horizoontal Overtuurn”: overturn the seleccted letter hoorizontally.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
57
Chap
pter 7
Letter Pattern Operation
O
n
“Vertical Overturn”: overturn thhe selected letter
l
vertically.
“Clockw
wise Rotatioon”: use thhe letter as centre (“
” in the ceentre of lettter), and
rotate thee selected leetter clockw
wise.
3.. View and File Operattion
D
addjust the deensity of th
he letter strring. Press this key to
o display
“Letter Density”:
thedenssity dialog box,
b where user
u can sett stitch form
m, increase or
o decrease density.
“Stitchh Form”: shhow/hide thhe stitch fo
orm. Hidingg the stitch form can improve
operationn speed.
“Increase Densityy”: increasee the satin stitch
s
densitty of the crreated letterr pattern.
“Reduuce Densityy”: reduce satin stitch
h density of the created letter pattern.
n toward
“Left”, “Riight”, “Up” and “Down”: move leetter pattern
each direection.
“Reducee”: reduce to
t the displaay window of
o letter pattern.
“Enlargge”: enlarge to show thee detailed part of the leetter pattern.
58
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaapter 7
Letter Pattern
P
O
Operatio
on
“Actuaal”: show thhe letter patttern in the actual
a
size. At this tim
me, the size of
o pattern
in interfface is equaal to actual size.
s
“Center”: scale up/down
u
thee view, so as
a to show thhe whole paattern for ch
hecking.
“Save”: it is used for saving the edited letter patteern. After ppressing thiss key, the
system will displayy the windoow for userr to input th
he pattern number
n
and name. Acccording to
need, chhange the pattern
p
nam
me and numbber (the num
mber is nott recommennded to be changed),
c
then preess confirmaation key too start savinng.
“Exit”: quit from “Create Lettter Pattern””.
4 Keys forr Adjusting Whole
4.
W
Arraangement
If you
y adjust the parameeters for whhole rank affter the edittion of the individual letter, the
edition of the indivvidual letter will be proobably replaaced.
“Horizoontal”: rankk the letters horizontally
y
Preess this keyy to shift am
mong “horizzontal”, “veertical”, “upp arc”, and “down arc””. Only in
case of
o “up arc” and “downn arc” can “fix
“ letter direction”,
d
“
“increase
raadian” and “decrease
radian”” be adjusteed.
“Verticaal”: rank lettters verticaally
“Up Arrc”: rank lettters in arc bending
b
upw
wards
“Downn Arc”: rankk letters in arc
a bending downwardss
“Fix Leetter Directiion”: when user ranks the letters in arc, the letter anglee will not
Owner’s Manual
M
of BECS- A15 Computerized Controll System
59
Chap
pter 7
Letter Pattern Operation
O
n
change along
a
with thhe position of arc, but fix
f at a certaain angle
“Increasee Radian”: when userr ranks thee letters in arc, this kkey can enlarge the
radian off the referennce arc
“Reducee Radian”: when
w
user ranks the lettters in arc, this key caan reduce th
he radian
of the refference arc
“Wholle Clockw
wise Rotatee”: rotate the whoole letter
“Enlaarge
Letteer
Intervaal”:
increease
the
interval
string cllockwise
between
letters
“Reducee Letter Inteerval”: reducce the interv
val betweenn letters
7.4 Savve Letterr Pattern
Afteer finishingg the letter pattern editt, user can press
user to innput patternn number annd name, andd then presss
60
to dissplay a win
ndow for
again to savve.
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chaapter 7
Letter Pattern
P
O
Operatio
on
Affter saving, system
s
willl return to thhe main inteerface for leetter embroiidery.
If there
t
is no need
n
to editt letter patteern, press
to quit and thhe following
g hint will
be dispplayed.
Preess
to save or press
to
o cancel savving, and rreturn to th
he pattern
manageement interfface.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
61
C
Chapter
8
Assisttant Opeeration
O
ion
Ch
hapterr 8 Asssistant Operati
Useer can perforrm some coommon assisstant operattions by pressing keys.
8.1 Fraame Selecction
Useer can press "
N
No.
1
" key
k to enter the interfacce for framee selection aand position
n.
Icon
Nam
me
Patteern Range Display
D
Fram
me Type Sellection
Posittion Patternn to the
Centter of the Frrame
2
Fram
me Parameteer Setting
Mov
ve Frame aloong Pattern
Outsside
Mov
ve Frame aloong Pattern
Outline
Mem
mory of Patttern Origin
62
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
C
Chapter
8
No.
Assisstant Op
peration
Icon
Naame
Reccovery of Paattern Origiin
2
Maanual Patternn Movemennt
Exiit
8.2 Cllear XY Displacem
D
ment
Thhis function is to clear the
t X and Y displacemeents.
1.
In thee main interfface
, press
p
2
2.
System
m will set current
c
X/Y value to 0.
Usser can checck the currennt X/Y valuue on the maain interfacee.
8.3 Poositioningg Idling
Thhis operationn can only be
b undertakeen under em
mbroidery confirmationn status
.
Thhis function can move the frame to
t certain position
p
withhout embrooidering acccording to
user’s need.
n
User can
c select color-changi
c
ing code orr stop code as reference to idle fo
orward (or
backwaard).
8
8.3.1.
Low
w Speed
d Idling Forward
F
d
1. In thee main interfface
, prress
2. Press
Owner’s Manual
M
of BECS- A15 Computerized Controll System
63
C
Chapter
8
(1) Press
Assisttant Opeeration
once to idlee forward by
b one stitchh
(2) Hold pressing
for 2s to idle forward conntinuously
8
8.3.2.
Low
w Speed Idling Backwar
B
d
1. In the main
m interfaace
, preess
2. Press
(1) Press
once to idlee backward
d by one stitch
for 2s to idle backward continuously
c
y
(2) Hold pressing
8
8.3.3.
Higgh Speed
d Idling Forward
F
d
1. In the main
m interfaace
2. Press
, preess
too idle forwaard at high speed
s
N
Note:
the opperation meethod of higgh speed idling backwaard is the sam
me with herre.
8
8.3.4.
Go to Next Color
1. In the main
m interfaace
2. Press
, preess
too idle to thee next color--changing code
c
Note: the operation
o
meethod of “goo to previou
us color” is the same w
with here.
64
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chapterr 9 Oth
her Funcctions
O
Function
F
ns
C
Chapt
ter 9 Other
These functioons can be
b used duuring the usage, inccluding maachine maiintenance,
informaation inquiryy and system
m settings.
to enter the interfacce for other function, where
w
a list of function keys will
Preess
be displlayed for usser to operatte by pressinng.
The words on the keys caan help userr understand
d the functioons.
9.1 Statistics
1.
Press
2
2.
Press
to enter thee interface for
f other funnctions.
to enter the innterface of statistics.
s
Owner’s Manual
M
of BECS- A15 Computerized Controll System
65
Chapterr 9
Oth
her Functtions
In the abbove interfa
face, the staatistic inforrmation is displayed
d
inn a chart. If user neeed check
details off each patterrn, press
Press
to return to the interfacce of statistics. Presss
informatiion and presss
66
to enter th
he correspoonding interfface.
to delete statistic
to return..
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chapterr 9 Oth
her Funcctions
9.2 Seet Frame Origin
Settting the fraame origin is the premise for savin
ng the patterrn’s start pooint and setting frame
protection at suddden power-off. So aftter the insttallation or maintenannce of macchine, it’s
necessaary to set thee frame origgin.
to enter thee interface for
f other funnctions.
1.
Press
2
2.
Press
3
3.
Selectt “Auto Findd Origin Pooint”
to enter debugging interfface.
Sysstem will move
m
the fraame automaatically and determine the
t origin aaccording to
o the limit
switchh. So please ensure thhat the lim
mit switch has
h been installed intto the macchine and
activatted.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
67
Chapterr 9
Oth
her Functtions
9.3 Lan
nguage
Systtem supportts Chinese, English, Tuurkish, Span
nish, and so on.
1.
Press
2..
Press
t enter the interface fo
to
or other funcctions.
to enter
e
languaage interface.
Seleect the langguage you want
w
and system
s
will enter the main
m
interfface in the selected
languagee.
9.4 Maachine In
nformatioon
Opeeration Proccedures:
68
1..
Press
2..
Press
t enter the interface fo
to
or other funcctions.
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Chapterr 9 Oth
her Funcctions
This function will help usser check machine
m
softw
ware inform
mation. Presss
to quit.
9.5 Machine
M
D
Debuggin
g
This operation
o
i only for repairman, ordinary users
is
u
are bbanned to undertake
u
these operations.
o
Because these
t
operaations invo
olve some mechanicall work, pllease pay
attention to the perrsonal safetyy and equippment securrity during thhe operatioon.
Deebugging funnction is too mainly useed for testin
ng, maintennance and faault inspectiion of the
machinee, which innclude the following function (debugging items will be differeentfor the
differennt models):
Debbugging Inteerface 1
Debuggingg Interface 2
Main Shaaft Speed And
A Encoderr Test
Main Shhaft
Main Shaaft to Any Angle
A
Main Shaaft Angle
Trimmin
ng solenoid/Motor
Trimming
Hold soleenoid/Motoor
Hook So
olenoid/Mottor
Breakagge Detectionn
Change needle poosition, neeedle bar
d adjust maiin shaft mannually
color and
Head Soolenoid/Mootor
Up, down
n, combinedd test
Owner’s Manual
M
of BECS- A15 Computerized Controll System
69
Chapter 9
Debugging Interface 1
Other Functions
Debugging Interface 2
Facial Suture Clamp
X-axis parameter test
Y-axis parameter test
Driver Parameter Test
Main shaft parameter test
Save driver parameters
Load driver parameters
Sensor Status Test
Test pull bar switch, frame limit, knife
origin,
knife
maximum
point,
thread-hooking origin, and needle
position display, etc.
Peripheral board upgrade
All Peripheral Board Write Address
Peripheral board
Management
Single Peripheral Board Write Address
All Peripheral Board Address Check
Single Perpheral Board Address Check
Perpheral Board Informa�on
Boot Loader Upgrade
Auto Find Origin
External CAN communication test
Other
External communication test
Touch screen correction
Param Export/Import
Import machine parameters
Export machine parameters
Param Init
Clear All Pa�erns
9.6 Date and Time
In date and time interface, user can check and modify the date and time of the system.
9.7 Touch Screen Correction
After using for a period, the touch screen may probably have the problem of the inaccurate
operation. This problem can be resolved by touch screen correction. During the correction,
please touch the very center of the cross displayed on the screen, or it may affect the future
70
Owner ’s Manual of BECS- A15 Computerized Control System
Chapterr 9 Oth
her Funcctions
operatioon. In orderr to avoid the
t trouble caused by the
t inaccurrate correctiion, this op
peration is
only forr the personn with authoorization.
1.
Press
2
2.
Press
to enter thee interface for
f other funnctions.
to enter debugging interfface, where user can seelect “Otherr” to enter
thhe corresponnding interfface.
3
3.
Press “touch screeen correctioon” to enterr the correcttion interfacce.
4
4.
Press the center of
o the crossees one by on
ne.
Duuring the process of coorrection, a lot of crossses will apppear on the screen. Usser should
press thhe center off them. Systtem receivees the data of
o those poiints and savves them ass standard
data forr correction..
5
5.
System
m will makke correctioon accordin
ng to the cooordinates oof points prressed by
ussers.
Sysstem will make
m
the correction
c
a then reeturn to the interface for other functions
and
automattically.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
71
Chapterr 10
On
nline Upd
date of Main
M
Sofftware
O
U
Update
of
o Main
n Softw
ware
Ch
hapterr 10 Online
Updatte Proced
dure
1. Hold
H
pressiing
and power on.
2. T
The screenn will displlay the folllowing inteerface, wheere user shhould selectt “update
program”
3. Select
S
the update
u
methhod
72
(via U disk)
d
Owner’s Manual of BECSB
A15 Com
mputerized Con
ntrol System
C
Chapter
10
Onlline Upd
date of Main
M
Sofftware
4. System will display
d
the window to “Select U Disk”,
D
and select
s
the taarget U disk.
5. After
A
enterinng the interfface of the U disk, selecct the progrram to be uppdated.
Owner’s Maanual of BECS-- A15 Computeerized Control System
S
73
Chapterr 10
6. Press
P
On
nline Upd
date of Main
M
Sofftware
to upddate.
7. When
W
finishhing updatee, system will
w automattically displlay a hint “uupdate com
mpleted, if
no others, please
p
restarrt”, and thenn please resstart.
74
Owner’s Manual of BECSB
A15 Com
mputerized Con
ntrol System
Chap
pter 11 Updatee of Softw
ware in Peripher
P
ral Boarrd
B
C
Chapte
er 11 Updatee of Sofftware inn Perippheral Board
Updatee Procedu
ure:
1..
Press
2..
Press
too enter the innterface forr other functtions.
to ennter the inteerface of staatistics.
Owner’s Maanual of BECS-- A15 Computeerized Control System
S
75
Chaapter 11
3
3.
Updatee of Software in Peripheeral Boarrd
Select “peripherall board mannagement” to enter thee managem
ment interfacce, where
user shhould select “peripherall board update”.
4
4.
76
Press
Owner’s Manual of BECSB
A15 Com
mputerized Con
ntrol System
Chap
pter 11 Updatee of Softw
ware in Peripher
P
ral Boarrd
5..
Select thhe U disk
6..
Select thhe program to be updatted and presss
Owner’s Maanual of BECS-- A15 Computeerized Control System
S
77
Chapter 11 Update of Software in Peripheral Board
7.
78
when system hint successful update, the update is completed.
Owner ’s Manual of BECS- A15 Computerized Control System
Appendix 1 Pa
arameterr List
A
Appendix
x 1 Para
ameter List
L
No.
N
Name
of Paarameter
D
Default
Valuue
Ran
nge of Valuee
Rem
marks
Com
mmon Parrameters
A01
A02
A03
Direction
D
R
Rotate
P
0
0~89
X
X&Y
Scaless
1
100/100
50%~2
200%
A04
A05
A06
A07
A08
Prior Mode
P
R Mode
Rep.
R Prior
Rep.
X
X&Y
Reps
X
X&Y
Intervval
Rotate
R
N
Normal
X Prior
1
1/1
0
0.0/0.0
Rotate,, Scale
Normal Part
X priorr, Y prior
1~99
-999.9~
~+999.9
Rotaating angle of
o the desiggn
Scale ratio of deesign in X /Y
/
direcction
Not used
E
Embroider
ry Assista
ant Param
meters
B01
A
Auto
Originn
Y
Yes
No, Yes
B02
T Do Cycliic Emb.
To
N
No
No, Yes
B13
Start for
S
C
Colors
Same
Y
Yes
No, Yes
S
Slow
After
0
0~3000
0
D15
STI..
P
Patch
D16
S
Speed
Afterr Patch
8
850
80~100
00
B18
S
Support
3D??
Y
Yes
No, Yes
C77
F
Filter
Short Stitch
Y
Yes
No, Yes
C78
C80
U57
Filtering Shhort Sti
F
0
0.5mm
L
Len
A
Auto
Jumpp Stitch
6
6mm
L
Len
S
Speed
off
Fast 10
1
l
ldling
0.1mm
m~0.6mm
6.0mm
m~12.0mm
Wheether to auto
omatically
repeat embroideering the
desiggn. It often accompaniees
repetition or thee special dessign.
Wheether to startt in
color-changing way when the
t
me to
laterr needle possition is sam
the fformer one
It is fit for high--speed machhine
usingg dahao serrvo-motor
driveer. It only get
g effective
afterr user confirrm the
embroidery agaain.
The same as abo
ove
The same to abo
ove
1~10
Owner’s Manual
M
of BECS- A15 Computerized Controll System
79
Appendix 1 Parameter List
No.
Name of Parameter
Default Value
Range of Value
Remarks
Thread-breakage Detection Parameters
B05
B11
B06
B08
B09
B10
B14
B12
C28
C67
C68
C69
C70
C90
T. B. Detect
Sti. Not T.B. Detect
Stop after T.B.
detect
T.B. Back Sti.
Back&Patch Count
Motion After Patch
Set All Heads
Patch
T. B. Detect When
Jump
T.B.Detect
Debouncing Sti
Upper Line Det.
Sensitivity
Bobbin
line
Det.Sensitivity
Upper Line Det.
Debouncing Sti
Bobbin line Det.
Debouncing Sti
T.B.D Device Type
Fault
K1
det.board
type
C91
Head motor Action
Angle
No
8 stitch
No, Yes
0 stitch ~15 stitch
Yes
No, Yes
0 stitch
0 stitch ~7 stitch
1 stitch ~9 stitch
2 stitch
Speed Down
Speed No Change,
Speed Down, Stop
No
No, Yes
No
No, Yes
1 stitch
1 stitch ~6 stitch
3
1~10
5
1~10
1 Sti
1~10 Sti.
5 Sti
1~10 Sti.
Wheel
Spring,
How many stitches to patch
before the thread break point
If “Yes”, all unclosed heads do
patching when patching.
Wheel,
Spring+Wheel
PC2220
PC2220,Other
0
0~10
Frame Parameter
C06
B03
C15
C16
80
Frame Curve &
Angle
Over frame by Step
High Frame-Shift
Speed
Low Frame-Shift
F4
F1~F6
No
No, Yes
16
1~30
12
1~30
Owner ’s Manual of BECS- A15 Computerized Control System
Appendix 1 Pa
arameterr List
No.
D13
C74
C75
C76
C85
Name of Paarameter Default
N
D
Valuue
Ran
nge of Valuee
S
Speed
S
Speed
Wheen Over
1
16
0,1,2,…
…,30
f
frame
230~28
80
It is fit for high--speed machhine
usingg Dahao serrvo-motor
driveer.
2
230
230~28
80
The same as abo
ove.
2
230
230~28
80
The same as abo
ove.
2
230
230~28
80
The same as abo
ove.
X directionn Frame
2
230
A
Angle
A
X direction Frame
A
Angle
B
Y direction Frame
A
Angle
A
Y direction Frame
A
Angle
B
Rem
marks
Main
n Shaft Pa
arameterss
C07
C09
Max. Speedd
M
M
Minimum
S
Speed
11100
4
400
C08
Shift Stitch Length
S
3
mm
C10
J
Jump
Stitchh Speed
6
600
C13
S Run Speeed
Set
8
80
250, 30
00, 350,…,11200
250,300
0,350,…,6000
1.0~10.0(commonn
type maachine), 3.00~
6.0 (hig
gh-speed
machin
ne using Dahhao
servo-m
motor driverr)
400~85
50(commonn
type maachine), 4000~
1100 (h
high-speed
machin
ne using Dahhao
servo-m
motor driverr)
80 90
0 … 1500
C12
S
Startup
Stitcches
2 stitch
1 stitch
h~9 stitch
D02
S
Startup
Acce.
1
15
1,2,3,…
…,30
C25
S Break Para.
Set
5
0~30
C24
M Motorr Para.
Main
4
0~30
Owner’s Manual
M
of BECS- A15 Computerized Controll System
Wheen the stitch
h length is
longger than the set value, thhe
machhine will lower the speeed.
Set tthe rotation
n speed for jump
j
stitchh.
Set tthe startup stitch
s
number
befoore accelerattion.
Increease the vallue to bring a
quicker speedup
p after presssing
the sstart key.
Rangge: 0~30. When
W
the maain
shaft
ft motor is an
electtromagneticc motor, the
valuue is usually
y set at 9. When
W
it is a servomoto
or, the
paraameter is usu
ually set at 5-7.
The parameter is
i invalid when
w
or. When it’ss an
it’s a servomoto
electtromagneticc motor,
increease this parrameter value
81
Appendix 1 Parameter List
No.
D14
D10
C05
C26
D53
C14
MS10
Name of Parameter
Default Value
Stop Ok bef. Pull
Bar
Yes
Ratio
of
Induction
0
-15% ~ +15%
0
0~3
15
0~30
Yes
No, Yes
80
80,400
Middle
Low,Middle,H
AC
Value for Thick
Cloth
Para. Of Needle
Down
Lock Motor When
Stop
Speed of Slow
Emb
Emb.Speed
Range of Value
Remarks
to avoid main shaft vibration
during braking. Usually it’s set
as 1.
No, Yes
The parameter is used when
the main shaft uses induction
motor. If the value is incorrect,
the set rotation speed will be
different from the virtual
speed.
Thread-trimming Parameters
C01
D04
C11
C21
Jump & Trim
Speed after Trim
Slow Stitches After
Trim
Length of Lock Sti.
(mm)
3 Jump
80
No Trim, 1 Jump~7
Jump
60,70,80…150
3 stitch
1 stitch ~7 stitch
0.6
0.3~1.5
C19
Lock Num. After
2
Trim
0~3
D06
Spin Rounds for
1
Brake
1,2
C23
Action after Trim
C22
Frame after Trim
Y
Frame-movin
g
No
D03
Set Hold Startup
-4
82
X Frame-moving, Y
Frame-moving Move
Needle
No, Yes
-4~3
The parameter sets the rotation
speed for lock stitch.
Set the lock stitch number at
pulling the bar for embroidery
after setting the trimming
2 for most machines, 1 for
mini type or machines with
servo control main shaft motor.
Owner ’s Manual of BECS- A15 Computerized Control System
Appendix 1 Pa
arameterr List
No.
D07
Name of Paarameter Default
N
D
Valuue
Ran
nge of Valuee
P
Para.
T
Trim
is OK
Yes
Y
No, Yes
D08
Hook Anglee by
H
M
Motor
-100
-100~+
+100
E39
Hook Distannce By
H
M
Motor
1
150
0~180
C17
P
Pause
Trimm
ming
N
No
No, Yes
3
1~8
8
80
80,90,1
100,…,250
Y
Yes
No, Yes
0
0.7
0.3~2
2
0~2
C18
D05
C20
D48
D49
T
Trim
Lenggth
Speed Whenn
S
T
Trimming
L
Lock
When Trim
L
Lock
Sti Len
b
bef.Trim
L
Lock
Sti beff.Trim
Rem
marks
Set tthe hook angle by motoor.
Wheen user increeases the vaalue,
the hhook angle is
i moved
backkward.
1 is tthe minimu
um length annd 8
are tthe maximu
um length.
C81
Cut action start
C
s
a
angle
C82
C return angle
Cut
a
adj 12
1
0~30
It is fit for the machine
m
usinng
steppping-motor for trimminng
threaad.
The same as abo
ove.
C83
Cut keeper return
C
r
a
angle
0
0~99
The same as abo
ove.
C84
H
Hold
voltagge adj
1
1~3
The same as abo
ove.
4
400
60~600
0
8
80
60~500
0
O
Open
Open, 1 times, 2tim
mes
O
Open
Open, 1 times, 2tim
mes
N
No
No, Yes
Stepping
S
m
motor
Steppin
ng motor,
C95
C96
C93
C94
E99
Speed At 1sst Sti.
S
B Trim
Bef.
S
Speed
At 2sst Sti.
B Trim
Bef.
W
When
the shhear line
s
surface
E
Emb
surfacee clip
a
action
way
P
Patch
emb surface
s
w
when
fully
0~20
8
H05
Trimming device
T
d
t
type
C110
T
Trim
Machiine Type 360
3
Solenoid
180, 36
60
The same as abo
ove.
Macchine Parameters
Owner’s Manual
M
of BECS- A15 Computerized Controll System
83
Appendix 1 Parameter List
No.
D01
D12
K2
C49
C50
C29
C71
E1
E2
E3
E4
H06
M100
K3
Name of Parameter
Default Value
Needles
6
1,2,…,MAXNEEDLE
12
0~30
0
0~7
0
0,1
0
0,1
No
1
No, 1~7
1~10
0
0
0
0
Yes
0~255
0~255
0~255
0~255
No, Yes
no
800
no,yes
80~800
1
1~10
Color-Change
Speed
Openloop stepper
change color curve
X compensation for
mechanical gap
Y compensation for
mechanical gap
Needle of Boring
Thread
hold
voltage adj.
DIP1
DIP2
DIP3
DIP4
Drive
failure
monitoring
Start needle light
Hat emb Speed
limit
D68
Number of heads
E45
Machine
distance
head 162
Range of Value
Remarks
Set the value according to the
machine situation. E.g. the
value should be 9 for 9-needle
machine. If the value is
different from the machine
needles, the color changing
will be abnormal.
1~1500
Net Parameters
C43
IP Address
C45
Subnet mask
C46
Gateway
84
It is used for setting machine
address when connected to PC.
It is not different among
different machines.
It is used for setting the subnet
mask of IP address when
connected to PC.
It is used for setting the
gateway of machine when
Owner ’s Manual of BECS- A15 Computerized Control System
Appendix 1 Pa
arameterr List
No.
N
Name
of Paarameter
D
Default
Valuue
Owner’s Manual
M
of BECS- A15 Computerized Controll System
Ran
nge of Valuee
Rem
marks
connnected to PC
C.
85
Appendix 2 Directions of U Disk Operation
Appendix 2 Directions of U Disk Operation
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
86
Operations
Methods or Standards
Same as floppy disk
Remarks
USB I/O
Operation priority between USB
USB Disk
disk and floppy disk
Format supported by USB disk
FAT16 and FAT32
Support long file name
Support, but not displayed
For instance: “
DOS 8.3 mode 8 digit
.DST” will
prefix is viewable,suffix is
File name format
be displayed as “
3 digits
~1.DST”
Support file name in Chinese
Support
Sub-directory operation
Support
No. It could be countless
Sub-directory limitation
in theory
File number in one sub-directory
400
Back to disk management
Reading & writing error/ change or design management
USB
interface, insert the disk
again.
Multi-logical disks in one USB
Support
Formatting USB
Support
Installation of the letter base
Not Support
Software update
Support
Special character in file name
Support, except “$”.
Owner ’s Manual of BECS- A15 Computerized Control System
Appendiix 3 Automattic Position Limitation
L
Function
F
Insttructions
foor Apparrel
E
Embroide
ery
App
pendix 3 Automaatic Posittion Lim
mitation Function
F
n Instrucctions
for App
parel Em
mbroideryy
A
Woorking Princciple
Thhe automaticc position limitation fuunction of single-head
s
embroideryy machine controller
is to dettermine the embroideryy range of the frame by
y setting thee distance fr
from the cen
nter of the
frame too the originn (that is X--/Y positionn limitation
n optical couupler) and tthe actual frame
fr
size
(unit: mm).
m
If em
mbroidery is to be doone beyond
d such rangge, the conntroller willl activate
automattic protectioon to prevennt damage too the mechaanical parts of the embrroidery macchine.
B
Settting Methodd
1 Set Framee Origin
Preess
key, then
t
press
Seelect "
key
y, to enter thhe followingg interface.
Auutomatic Orrigin Searchh", to enter the
t interfacee to search oorigin autom
matically;
the fraame will seaarch and dettermine the origin auto
omatically; press
p
"
Owner’s Manual
M
of BECS- A15 Computerized Controll System
" key to
o quit.
87
Appendixx 3 Automatiic Position Liimitation Fu
unction Instrructions
forr Appareel
Em
mbroiderry
2
Clear XY Displacemen
D
nt
In thhe main inteerface, press "
3
" key
k to clear the XY dispplacement ddisplayed heere.
M
Manual
Fraame-movingg
I the mainn interface, click the frame-movi
In
f
ng key to move
m
the fframe to ov
verlap its
centeer with the needle
n
hole.
88
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Appendiix 3 Automattic Position Limitation
L
Function
F
Insttructions
foor Apparrel
E
Embroide
ery
4
Set Framee Center andd Size
In the main innterface, cheeck the coorrdinates of XY,
X which is
i the position of framee center.
Preess "
press "
" key, to enter
e
the innterface for frame selection and pposition settting; then
k to enterr the interfacce for settin
ng related parameters, w
where user can input
" key,
the coorrdinates of XY
X in the main
m interfacce.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
89
Appendixx 3 Automatiic Position Liimitation Fu
unction Instrructions
forr Appareel
Em
mbroiderry
Theere are four parameters: "X directioon center" means
m
the distance
d
at X direction between
the fram
me center annd X- direcction positiion limitation optical coupler; "Y
Y direction
n center"
means thhe distance at
a Y directioon between the frame center
c
and Y+
Y directionn position liimitation
optical coupler.
c
"X
X direction frame size" means th
he embroiddery range of the fram
me at X
directionn; "Y direction frame size" means the
t embroid
dery range of
o the framee at Y directtion.
Y Frame Actual Siize W
X Frame Actual
A
Size L
"X direction
d
fraame size" annd "Y direcction frame size" shouldd be set acccording to th
he actual
size of different
d
fram
mes. Note: this param
meter need be
b set accorrding to thee actual emb
broidery
range of the frame, for
f the appaarel frame iss usually no
ot square.
90
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
Appendiix 3 Automattic Position Limitation
L
Function
F
Insttructions
foor Apparrel
E
Embroide
ery
C
Canncel Position Limitation
Sett "Frame Selection" ass "No Fram
me", the position limitation functiion will be canceled
and the software prrotection forr the frame of flat emb
broidery will also becom
me invalid.
Owner’s Manual
M
of BECS- A15 Computerized Controll System
91
Appendixx 3 Automatiic Position Liimitation Fu
unction Instrructions
forr Appareel
Em
mbroiderry
D
Com
mmon Framee Size (Unitt: mm)
Frame 1:
Size: 5500×375
Embroidery Range: 430×260
Frame
F
2:
Size:
S
290×2990
Embroidery
E
y Range: 2300×230
Frame 3:
Size: 2000
Embroidery Range: 150
Frame
F
4:
Size:
S
150
Embroidery
E
Range: 1000
Frame 5:
Size: 1200
Embroidery Range: 90
Frame
F
6:
Size:
S
90
Embroidery
E
Range: 40
92
Owner’s Manual of BE
ECS- A15 Com
mputerized Contrrol System
BECS-
F.
F
nfirm
Con
Embroidery Confirmation
Frame Position
n:
Frame Selection:
Usse direction keys
E Frame Selecttion and Position
E.
n
a
adjustment,
empty
y feed, etc.
":
,
,
to adjust frame
f
position
Staart
G. Start Em
mbroidery
,
Reelease Confirmatiion
H. Release Em
mbroidery Confirrmation
ming, main shaft jog, frame setting
g, color-changing and start mode setting, manual fraame-moving, speeed
": thread trimm
ace: set color-channging sequence.
D. Under this Interfa
C Modify Emb
broidery Parametters: A01-A08: cllick to set.
C.
M
Main
Interface "
repeat, appliqué, needle bar color setting, etc.
":
" direction, anglle, X/Y scaling, priority Color--changing Sequeence Setting "
ge keys to select ppattern
: use pag
setting, etc.
C
Parametter Setting "
Common
,
B. Seelect Pattern for Embroidery
y pattern preview, letter pattern opeeration, delete patttern, pattern inputt/output, pattern fuunction setting, ettc.
": memory
keys to selectt patterns
Use page
p
A Input Pattern
A.
n
Pattern
P
ment "
Managem
P
Part
I. Embrroidery
C
Operation Quick
k Guide
Appen
ndix 4 A15 Controller
peration Quiick Guide
/Appendiix 4 A15 Controller Op
93
94
A15 Controller Operation Quick Guide
Owner ’s Manual of BECS- A15 Computerized Control System
If user, after releasing embroidery confirmation, wants to embroidery the pattern again, user need operate from step B "Select Pattern for Embroidery" again.
Appendix 4
C. Main
Shaft Jog
M
Owner’s Man
nual of BECS- A15 Co
omputerized Control System
8. Return to Em
mbroidery Stop Point
6. Empty Feed and Advance at High Speed
nging Code
Locate the Next Color-chan
4
,
mbroidery Start Point
7. Return to Em
,
5. Empty Feed and Return at High
H
Speed
Speed Shift Key:
Directiion Keys:
D. Manual
M
Frame-mooving
nging Code
Locate the Last Color-chan
pressing for 2s
: (1) clicck once to advancee by 1 stitch; (2) hold
h
2 to advance con
ntinually;
Empty Feed and Advance aat low Speed
b 1 stitch; (2) holld pressing for 2s to return continuaally;
: (1) clicck once to return by
Empty Feed and Return at Low Speed
al Color-changin
ng
B. Manua
Part II. Manual Operation
O
A15 Controller Operation
O
Guide
Q
Quick
3
2
1
E. Empty Feed
A. Manual Triimming
Appen
ndix 4
,
;
95