Installation Guideline (Fix 100M to the DJI M300)

Installation Guideline
(how to fix GS-100M LiDAR Scanning System to the DJI M300)
1. Check the accessories according to technical list after get the parcel, as figure 1
Figure 1
And photos of package
Figure 2
Figure 3
Wuhan Geosun Navigation Technology Co.Ltd
Website: www.geosun-gnss.com.cn
Add: 4F, Building D, Maker plaza No.8 West Maodianshan Road,
East Lake Hi-tech Zone Wuhan City, China
Figure 4
Tel: +86 27 87504895
Fax: +86 27 87504895
Specification of accessories
1)
2)
3)
4)
5)
Figure 5
Figure 6
Figure 7
GNSS antenna and cable which attached the antenna bracket (Figure 6)
Camera PPK event data cable (Figure 5)
Power switch cable (Figure 7)
Micro SD card insert into LiDAR scanning system
Flash (Shuttle software and gAirhawk software and license)
2. Fix the lower frame to the GS-100M body.
Figure 8
Figure 9
There are 4 holes for fixing upper frame, with 4 x M3 studs and plastic ring.
Wuhan Geosun Navigation Technology Co.Ltd
Website: www.geosun-gnss.com.cn
Add: 4F, Building D, Maker plaza No.8 West Maodianshan Road,
East Lake Hi-tech Zone Wuhan City, China
Tel: +86 27 87504895
Fax: +86 27 87504895
Figure 10
Figure 11
3. Fixed the Upper frame to the DJI M300 drone
Figure 11
Figure 12
1) Disassemble the origin screws (Figure 11)
2) Fixed the Upper frame to the DJI M300 drone (Figure 12)
3) Fixed the GS-100m LiDAR scanning system to the drone
Please pay attention to the direction of the LiDAR and the drone, both of them should be
Wuhan Geosun Navigation Technology Co.Ltd
Website: www.geosun-gnss.com.cn
Add: 4F, Building D, Maker plaza No.8 West Maodianshan Road,
East Lake Hi-tech Zone Wuhan City, China
Tel: +86 27 87504895
Fax: +86 27 87504895
ahead(Same direction).
Figure 13
Figure 14
4. Power line Connection
Figure 15
Figure 16
Connected the drone to the lidar with cable line (Figure 15, 16).
Wuhan Geosun Navigation Technology Co.Ltd
Website: www.geosun-gnss.com.cn
Add: 4F, Building D, Maker plaza No.8 West Maodianshan Road,
East Lake Hi-tech Zone Wuhan City, China
Tel: +86 27 87504895
Fax: +86 27 87504895
Figure 16
5. Power checking before flight
Figure 17
4 led indicators, 4 input interface, 1 Micro SD card slot
PWR: power indicator (Light on)
GNSS: GNSS satellite indicator (flashes one time/sec)
TRIG: Camera indicator (flashes one time/2 sec)
LIDAR: LiDAR indicator (flashes one time/sec)
Slot : Insert 128GB Micro SD card (POS and LiDAR data)
Before power on, check SD card connection; Pull out then insert SD card.
Power on, 4 led indicators turn on then 3 of them turn off only left P indicator light on, then T
indicator flashes. After G indicator flashes, 2-3 minutes initial and static, during these time L
indicator flashes. It is working in order, the drone is ready for flight.
Wuhan Geosun Navigation Technology Co.Ltd
Website: www.geosun-gnss.com.cn
Add: 4F, Building D, Maker plaza No.8 West Maodianshan Road,
East Lake Hi-tech Zone Wuhan City, China
Tel: +86 27 87504895
Fax: +86 27 87504895