important warranty information

IMPORTANT WARRANTY INFORMATION
Thank you for choosing TAYLOR…The finest performance ignition wire available.
At Taylor Cable we take every measure to manufacture our product to meet the highest quality specifications and
standards available. However, from time to time it is possible that a product may become defective during use. If
such should occur, Taylor Cable will make every attempt within a reasonable request and under our warranty
guidelines to make the warranty replacement process as smooth as possible.
These ignition wires will withstand temperatures up to 600º F. They are NOT guaranteed against burns from
direct contact with a header or exhaust manifold and/or higher temperatures or radiant heat in excess of 600º F.
For the best Performance and Protection from heat under extreme conditions, we highly recommend the use of our
Space Age Boot Protectors, as listed below:
Universal-Fit Set
COLORS
Silver
Black
Blue
Yellow
Orange
Red
1 Pack
2523
2559
2565
2563
2567
2561
8 Pack
2524
2560
2566
2564
2568
2562
Custom-Fit Set
1 Pack
2417
2409
2415
8 Pack
2418
2410
2416
2411
2412
Taylor offers two different styles of boot
protectors depending on your application
with heat protection up to 1200ºF.
The Universal-Fit Boot Protector is designed
for 90º, 135º, and 180º spark plug boots on
Universal sets prior to the termination and
installation of the distributor terminal and
boot.
The Custom-Fit Boot Protector is designed
with a larger opening (no ring) to fit directly
over 90º, 135º, and 180º spark plug boots on
Custom-Fit, Race-Fit, and Universal-Fit sets
where both plug & distributor boots have
been installed.
Protect Your Investment….and make
Spark Plug Removal Easy with the Taylor
Spark Plug Boot Removal Tool!
 Removes wire from plug without
damaging the wire and plug boot.
 Insulated handle prevents burns to
hands and fingers.
 Part Number 43392
Multi Purpose Wire Tool…Crimps
7-8mm Spark Plug wire terminal ends.
 Part Number 43390
Strip & Crimp Tool… Crimp and Strip
8mm & 10.4mm Spiro-Pro wire without
damaging the wire or core.
 Part Number 43395
Professional Wire Crimp Tool…Positive
ratchet system adjusts to produce a factory
quality crimp each and every time.
 Part Number 43400
43390 & 43395
Form #IS021 Rev D 10/13
43400
TAYLOR IGNITION WIRE SETS-LIMITED 90-DAY WARRANTY
Taylor Cable Products, Inc. warrants solely to the original purchaser and not to any subsequent
purchaser, and only as installed on the car or truck it was originally installed, that this Taylor ignition
wire set is free from defects in materials and workmanship and under normal operating conditions will
not fail for the period of time from when the wire set was purchased by the owner of the vehicle on which
this set was originally installed as long as that vehicle is owned by the original purchaser.
If failure should occur, return defective ignition wire set, with dated proof of purchase, and this
warranty, to an authorized Taylor dealer for verification and replacement under this warranty. This
warranty is limited to the replacement of the defective wire set, at the sole discretion of Taylor Cable
Products, Inc. to the extent permitted by law. Cost for removal and installation is not included.
Warranty is extended solely to the original purchaser. Taylor Cable Products, Inc. is not responsible for
injury, property damage, or, other consequential damages arising directly or indirectly from an actual or
alleged defect in material and/or workmanship.
GARANTIA LIMITADA DE 90 DIAS DE LOS JUEGOS DE CABLE
DE ENCENDIDO DE TAYLOR
Taylor Cable Products, Inc. Garantiza solamente al comprador original y no a cualquier comprador
subsecuente, y solamente cables instalados originalmente en el automóvil o camión, que este cable de
encendido de Taylor este libre de defectos de material y mano de obra y que bajo condiciones de operación
normales no fallara por el periodo de tiempo a partir del cual fue comprado el juego de cables por el
propietario del vehiculo en el cual el juego fue originalmente instalado, durante todo el tiempo que el
vehiculo pertenezca al comprador original.
En el caso que falle, regrese el juego de cables de encendido con una comprobación con fecha de la
compra, y esta garantía a un distribuidor autorizado por Taylor Cable Products para la verificación y
reemplazo seguín esta garantía. Esta garantía esta limitada al reemplazo del juego de cables defectuoso a
la discreción bajo de Taylor Cable Products, Inc. Según lo permitido por la ley. El costo de remover o de
instalación no esta incluido. La garantía se extiende solamente al comprador original. Taylor Cable
Products, Inc. No es responsable por heridas, danos a las propiedades otros danos en consecuencia que
surjan directamente o indirectamente de un defecto real o supuesto en el material o causado por la mano
de obra.
TAYLOR CABLE PRODUCTS, INC
301 HIGHGROVE ROAD
GRANDVIEW, MO 64030
PH: 1-816-765-5011 FAX: 1-816-765-2452
[email protected] / www.taylorvertex.com
Form IS021 Rev D 10/13