FT IMPAC_FIBERGLASS_MIN

IMPAC
Irish Green
FIBERGLASS MINERAL SURFACE ROLL ROOFING
River Stone
Description:
Arizona Sand
IMPAC® Fiberglass Mineral Surfaced Roll Roofing is a
glass fiber reinforced asphalt coated product with granular
surface to protect against UV, weathering and physical
damage. It is lightly coated with a mineral release material
on the bottom side.
Grand Canyon
Granule Surface
Usage:
Modified Bitumen
Glass Yarn Reinforced Polyester
Modified Bitumen
Polyethylen Film
Fiberglass Mineral Surfaced Roll Roofing is a general
purpose roofing product designed for use in new roofing
and re-roofing installation utilizing hot mopping asphalt,
cold process adhesives or mechanical fasteners. While
frequently used for residential low-slope applications such
as porches and carpots or as flashing material, it can also
be used as a base sheet in commercial applications.
PRESENTACIÓN
Features and Benefits:
Versatile and easy to handle
Durable and cost-effective.
Reinforced with glass fiber mat ensuring dimensional
stability during installation.
Specially formulated asphalt gives lasting performance.
Minimal dead load weight
Rolls lay flat and resist wrinkling for easy application.
Low-slope residential and commercial use
Granular surfacing available in multiple colors to
complement most shingle applications.
ROLLOS
MEASURE
1.00 m width x 10.00 m long
FINISH
Gravel
In specific cases request information from our technical department
Important: All our products have been manufactured according to strict quality
standards and fulfilling every reasonable precaution, the information we are
providing is correct according to our experience, products as they are sell comply
with the aims to which they are been manufactured. Nevertheless we can not be
responsible for the variations in the use method or conditions to be applied by the
buyer.
Caution:
Storage and Handling
Fiberglass Mineral Surfaced Roll Roofing requires
protection from damage and the weather. Constantly
store rolls upright in a dry location and never more than
two pallets high. When storing two pallets high, position
a plywood sheet between pallets.
The existing roof coating systems should be completely
removed from the surface to be protected. The area to
be coated must not have bulges that can damage the
asphaltic membrane. Do not place heavy objects on the
newly installed cloth without the suitable protection to
prevent damage. During the installation with a gas
blowtorch do not exceed in the flamed because it
damages the reinforcement and the properties of the
polymers that modify the asphalt. The application with
blowtorch can only be fulfilled when the prime is dry. The
IMPAC® prefabricated must not be stored exposed to
heat, it should be stowed only in a vertical position and
where the room temperature is not higher than 45°C. It
is not resistant to oils neither solvents.
Update: September/8/2010. These technical specifications replace any previous one up to this date. Visit our webpage www.impac.com.mx where you can find the current version.
Subjected to changes without notice.
www.impac.com.mx
IP-PRE-MIN-NR00/0910
Aplicaction:
All roofing materials must be kept clean and free of
moisture prior to installation.
Warm weather conditions are ideal for good
adhesion.Application should be made when ambient
temperatures are 50º F or higher.
Deck must be free of voids, clean and dry.
Cut membrane sheets into manageable lengths before
installation.
Apply over roof decks with inclines of not less than 2
inches per foot.
Instal in a horizontal manner, overlapping a minimum of 2
inches on side laps and a minimum of 6 inches on end
laps.
To ensure product integrity, do not use in excess of 1/8
inch thickness of lap cement.
Install flashings in cement before nailing in place.
MINERALIZADO FIBRA DE VIDRIO GRAVILLA
IMPAC FIBERGLASS MINERAL SURFACE ROLL ROOFING
PROPERTIES
MELTING POINT
VALUE
METHOD
ASTMD-36
D-36
ASTM
212-110
-230ºC
ºF
100
FIBERDEGLASS
FIBRA
VIDRIO
INTERMEDIATE REINFORCEMENT
RESISTANCE TO
LONGITUDINAL STRAIN
ASTM D-5147
ASTM
D-5147
190
190 NN min.
min.
RESISTANCE TO
TRANSVERSAL STRAIN
ASTM D-5147
D-5147
ASTM
145 N
N min.
min.
145
ASTM D-5147
ASTM
D-5147
30
-1 ºF
ºC
FLEXIBILITY FOR
TEMPERATURE
ACTUAL PERFORMANCE
8.9m2
m2
8.2
www.impac.com.mx
IP-PRE-MIN-NR00/0910