Manual MONTAGEM CAUDA

ASSEMBLE MANUAL
MAGIC GS - 700
The piece Elevator – Horizontal Stabilizer is positioned in the tail of
the fuselage, like it is indicated in the pictures.
Insure the piece: Stabilizer-Horizontal Elevator to the badges
leading and back of the tial with 1 screw AN3-4A in each one of the
badges of the fuselage with their respective Nuts and Washers
(3/16”).
And then rivet the piece that ties the stabilizer-Elevator to the
fusselage.
www.aircraft-ibis.com
[email protected]
It carried out the connection of the Trim Wire to the
connector in the fuselage.
Later on, fix the Elevator Tube to the Elevator pivots with a screw
AN5-12A and their respective Nut and Washer (5/16”).
PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA
MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA
TELEFAX: (57-2) 5504280 / 6814433 EXT 5
MÓVIL: (57-314) 7925413 / 7926626
MEM - 0006 - P1
Rev. 001
ASSEMBLE MANUAL
MAGIC GS - 700
The piece Vertical Stabilizer is positioned in the tail of the fuselage,
above the Horizontal Stabilizer-Elevator, like it is indicated in the
pictures.
The Back screws are positioned from the back part of the Fuselage
to the Vertical Stabilizer with Screws AN3-4A with their respective
Nuts and Washers (3/16”), 2 units.
In the inferior front part of the
Vertical Stabilizer, in the badge of
the stabilizer 2 screws AN3-4A are
positioned and insured. (These
Screws don't need nuts and
washers since in the derive exist
Nut Plates that assure the screws).
Later on the Lateral screws of the back part of the fuselage are
positioned, screws AN3-4A in each one of the sides and they are
insured with their respective Nuts and Washers (3/16”), 2 units.
www.aircraft-ibis.com
[email protected]
PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA
MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA
TELEFAX: (57-2) 5504280 / 6814433 EXT 5
MÓVIL: (57-314) 7925413 / 7926626
MEM - 0006 - P2
Rev. 001
ASSEMBLE MANUAL
MAGIC GS - 700
In the superior part of the
assemble between the Rudder
and the Vertical Stabilizer, insure
a screw AN3-6A with their
respective Nut and Washers
(3/16”).
The piece rudder is positioned the tile of the fuselage with the
Vertical Stabilizer, as it is indicated in the pictures.
In the central part of the assembles among the Rudder and The
Vertical Stabilizer, insured with a screw AN3-7A with their
corresponding Bushing and their respective Nut and Washers
(3/16”).
www.aircraft-ibis.com
[email protected]
In the inferior part of the assembles among the Rudder and The
back part of the fuselage, insured with a screw AN3-7A with their
corresponding Bushing and their respective Nut and Washers
(3/16”).
PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA
MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA
TELEFAX: (57-2) 5504280 / 6814433 EXT 5
MÓVIL: (57-314) 7925413 / 7926626
MEM - 0006 - P3
Rev. 001
ASSEMBLE MANUAL
MAGIC GS - 700
The spring elevator is positioned in the superior part, in the piece
Vertical Stabilizer, and in the inferior part, in the piece Elevator.
Once positioned the spring of the elevator spends to close the
inspection cover of the Vertical Stabilizer with rivet 30 and both
covers of the fuselage and horizontal stabilizer equally with rivets
30.
The Tip Fearing is riveted like it is shown in the pictures, all with rivet
30.
In the inferior part of the Rudder insure the control cable, right and
left to the plate of the Rudder with fasteners AN3 - 5A, with their
respective Nuts and Washers (3/16”). The adjustment of the screws
should not interrupt the movement of the shackle.
www.aircraft-ibis.com
[email protected]
PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA
MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA
TELEFAX: (57-2) 5504280 / 6814433 EXT 5
MÓVIL: (57-314) 7925413 / 7926626
MEM - 0006 - P4
Rev. 001