PREPARED
BY
CHECKED
BY
NA
PTT PUBLIC COMPANY LIMITED
ONSHORE COMPRESSOR STATION 4
PROJECT
APPROVED
BY
CERTIFIED
(PTT)
REV.
DATE
NO.
D1
18-Feb-08
D2
21-Jul-08
NA
REVISED
BY
APPROVED
BY
NA
NA
DESCRIPTION
ISSUED FOR INTERNAL REVIEW
REVISIO ISSUED FOR ITB
SPECIFICATION FOR
DESIGN OF MACHINE FOUNDATION
SPC 0804.02-40.11 REV.D2
TOTAL 11 PAGES
AREA CODE OF SITE LOCATION
.
GENERAL AREA: 010
PTT PLC. CONTRACT NO.
PTT PLC. PROJECT NO.
0804.02
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 2 of 11
REV: D2
CONTENTS
SECTION
1.0
SCOPE .......................................................................................... 3
2.0
DEFINITIONS................................................................................. 3
3.0
REFERENCES ................................................................................ 3
4.0
MACHINERY DEFINITIONS.............................................................. 3
5.0
DESIGN OF ALL MACHINERY FOUNDATIONS ................................... 4
6.0
DESIGN OF RECIPROCATING MACHINERY FOUNDATIONS................. 7
7.0
DESIGN OF ROTATING MACHINERY FOUNDATIONS ......................... 8
8.0
SOILS DATA ............................................................................... 10
9.0
ANTI-VIBRATION MOUNTINGS ..................................................... 11
10.0
ENVIRONMENTAL REQUIREMENTS................................................ 11
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
1.0
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 3 of 11
REV: D2
SCOPE
This Standard specifies the basis for the design of foundations and
structures supporting reciprocating and rotating machinery to be used in the
design foundations.
2.0
DEFINITIONS
For the purpose of this standard the definitions as defined in Section I of the
PROJECT SPECIFICATION apply.
3.0
REFERENCES
Foundations and structures supporting machinery shall be designed in
accordance with the latest available revision of the following Standards,
Codes of Practices and Statutory Legislation.
3.1
Engineering Standards
SPC 0804.02-40.09
Design of Concrete Foundations, Structures
and Paving
Structural Steelwork Design
SPC 0804.02-40.07
3.2
National/International Standards
BS CP 2012 : Part 1
-
DIN 4024
-
4.0
MACHINERY DEFINITIONS
4.1
Reciprocating Machinery
Code of Practice for Foundations for
Machinery Foundations for Reciprocating
Machines
Supporting Structures for Rotary Machines
Machinery with reciprocating masses as major moving parts shall be
supported as close to grade elevation as possible directly on a rigid block.
4.2
Rotating Machinery
Machinery with rotating masses as major moving parts shall be supported
on a rigid block or on an elevated structure.
4.3
Foundation Grouping
For the purpose of this Standard, machine foundations shall be grouped as
shown in Table 1.
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 4 of 11
REV: D2
MACHINE
DYNAMIC
FOUNDATION
WEIGHT
ANALYSIS
GROUP TYPE
MACHINE TYPE (KG)
RECOMMEND
A
Rigid Block
Reciprocating
<2500
No
B
Rigid Block
Reciprocating
2500
Yes
C
Rigid Block
Rotating
--See Note 1
D
Elevated Struct.
Rotating
<2500
See Note 2
E
Elevated Struct.
Rotating
2500
Yes
NOTE 1: The analysis performed for rotating machinery supported on a rigid
block foundation shall take into consideration the operating speed of the
machine and the loading imposed by the machine on the foundation.
NOTE 2: The analysis performed for rotating machinery weighing less than
2500kg and supported on an elevated structure, shall take into consideration
the nature of the supporting structure, the location and speed of the machine,
and the loading imposed by the machine on the structure.
TABLE 1
FOUNDATION GROUPING
Where reciprocating and rotating machines are fixed to a common
foundation the loads shall be determined from the relevant sections of this
Standard for each machine and the foundation designed for the
reciprocating machine.
5.0
DESIGN OF ALL MACHINERY FOUNDATIONS
Reciprocating or rotating machinery foundations shall be designed in
accordance with the following: -
5.1
Health and Safety
Designs shall comply with all relevant National/International Health and
Safety Regulations imposed on engineers, suppliers, manufacturers and
importers.
5.2
Shape of Foundation
Clean, simple outlines shall be used for foundations. Beams and columns
shall be of a uniform rectangular shape. Block foundations should be
rectangular.
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
5.3
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 5 of 11
REV: D2
Pockets
Pockets where vapour could accumulate shall be avoided.
5.4
Elevation
The elevation of the machine support above grade shall be the minimum to
accommodate suction and discharge piping arrangements, oil drainage
requirements or, when condensing turbines are used, by the condenser
dimensions and the condensate pump.
5.5
Adjacent Structures
All parts of the foundation and superstructure shall be kept independent of
adjacent foundations, structures and buildings.
Concrete floor slabs
adjacent to the machinery foundation shall be isolated from the foundation
by a suitable isolation/expansion joint as defined in SPC 0804.02-40.09.
5.6
Thickness of Foundation
Thickness of the rigid block or foundation base slab for machinery shall not
be less than: Where L (in metres) is the greater of the length or breadth
0.60 + L
30
Where two or more machines are on a common foundation, L shall be the
greater of:
a) the breadth of the common foundation, or
b) the length of the longest segment assigned to any one machine.
5.7
Fatigue
To prevent fatigue failures, all sections shall be proportioned to resist the
sum of the static dead and live loads, plus an equivalent static force equal
to three times the dynamic force determined from analysis.
5.8
Shrinkage and Thermal Expansion
The effects of shrinkage and thermal expansion shall be taken into account
to prevent cracking. The minimum quantity of reinforcement in concrete
shall be 50 kg/m3, except for base slabs and rigid blocks which shall
contain at least 30 kg/m³.
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
5.9
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 6 of 11
REV: D2
Dynamic Modulus of Elasticity
The dynamic modulus of elasticity of concrete shall be based on the
specified 28-day strength test results (standard cube or standard cylinder
strength).
5.10
Soil Bearing Pressure
For spread foundations, soil-bearing pressures under static conditions shall
not exceed 50% of the net allowable bearing capacity.
For piled
foundations no reduction in the allowable pile capacity is required.
Earthquake loading shall be included.
5.11
Static Design
Static design shall include the weight of the machinery, auxiliary equipment,
piping and pipe thrusts, vacuum forces (in the case of condensing
operations).
Other applied loads shall include the following: -
5.11.1
Vertical Impact
Vertical impact of 50% of the dead weight of the machine and base plate.
5.11.2
Lateral Force
A lateral force of 25% of the weight of each machine including its base
plate applied normal to its shaft at a point midway between its end
supports.
5.11.3
Longitudinal Force
A longitudinal force of 25% of the weight of each machine and its base
plate applied along the shaft axis.
5.11.4
Combined Lateral and Longitudinal Forces
Lateral and longitudinal forces shall not be considered to act concurrently.
5.12
Damping
Where natural frequencies fall within the range 0.7 to 1.3 x operating
speeds analysis shall include for the contribution of damping. In the
absence of more specific information, values of 10% for concrete and 15%
piles may be employed.
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
6.0
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 7 of 11
REV: D2
DESIGN OF RECIPROCATING MACHINERY FOUNDATIONS
Foundations for all reciprocating machinery shall be designed in accordance
with the following: -
6.1
Common Foundations
Where two or more reciprocating machines are located adjacent to each
other they may be anchored to a common foundation when the net result is
reduced amplitudes.
6.2
Pulsation Bottles
Pulsation bottles shall have their supports integral with the compressor
foundation.
6.3
Eccentricities
The foundation shall be designed so that the horizontal eccentricity, in
either direction, between the centroid of mass of the machine foundation
system and the centroid of the base contact area or pile group, shall not
exceed 5% of the respective base dimension. The centroid of mass of the
machine/foundation shall, whenever possible, lie below the top of the
foundation block.
6.4
Unbalanced Forces and Moments
Design shall include for unbalanced forces and moments. This shall include
unbalanced moments obtained by multiplying the unbalanced forces by their
eccentricities.
6.5
Group A Reciprocating Machinery Foundations
Group A reciprocating machinery foundations are defined as rigid block
foundations for reciprocating machinery weighing less than 2500 kg.
Such foundations are not subject to dynamic analysis but the weight of
foundation shall be at least five times the total weight of machinery
including base plate.
6.6
Group B - Reciprocating Machinery Foundations
Group B reciprocating machinery foundations are defined as foundations for
machinery weighing 2500kg or more. Such foundation shall be subject to
dynamic analysis as follows: -
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
6.6.1
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 8 of 11
REV: D2
Design Codes
A dynamic analysis including the calculation of natural frequencies and
amplitudes shall be carried out in accordance with the recommendations of
British Standard BSCP 2012: Part 1 or equivalent. In case of conflicts
between Code of Practice and this Standard, precedence shall be given to
this Standard.
6.6.2
Primary Forces
Primary forces, couples and moments shall be applied at the machine
speed, over the full range of specified operating speeds, for the calculation
of primary amplitudes.
6.6.3
Secondary Forces
Secondary forces, couples and moments shall be applied at twice the
machine speed, over the full range of specified operating speeds, for the
calculation of secondary amplitudes.
6.6.4
Amplitudes
Total amplitudes shall be calculated by combining, in phase, primary and
secondary amplitudes. Maximum permissible single amplitudes shall be in
accordance with the recommendations of British Standard BSCP 2012: Part
1 or equivalent.
7.0
DESIGN OF ROTATING MACHINERY FOUNDATIONS
Foundations for all rotating machinery shall be designed in accordance with
the following: -
7.1
General
7.1.1
Dynamic Forces
Amplitudes shall be determined using dynamic forces from each rotor,
calculated as follows in the absence of more accurate information: Dynamic force (kg) = (rotor weight, kg) x (rotor speed, r.p.m.)
6000
With more than one rotor, amplitudes shall be computed with the rotor
forces assumed in phase and 180o out of phase to obtain, respectively, the
maximum translational and torsional amplitudes.
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
7.1.2
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 9 of 11
REV: D2
Amplitudes
Permissible amplitudes shall not exceed machine manufacturer's
requirements or the following whichever is more stringent: The amplitude which causes the effective velocity of vibration to exceed:
a) 1.8mm/sec at the machine bearings
b) 2.3mm/sec at any point on the foundation
7.2
Group C Rotating Machinery Foundation
Group C rotating equipment foundations are defined as rigid block
foundations to which dynamic analysis shall be carried (Refer Note Table 1)
except where the weight of foundation shall be at least three times the total
weight of machinery including base plate.
Where dynamic analysis is required then a rigid block foundation shall be
designed in accordance with the approach identified in Section 5.6 of this
Standard.
7.3
Group D Rotating Machinery Foundation
Group D rotating equipment foundation are defined as elevated structure
foundation for rotating equipment weighing less than 2,500kg.
Where dynamic analysis is required by table 1 then such design shall be in
accordance with Section 6.4 of this Standard.
7.4
Group E Rotating Machinery Foundations
Group E rotating equipment foundations are defined as elevated structure
foundations for rotating equipment weighing 2,500kg or more. Such
foundations shall be subject to dynamic analysis as follows: -
7.4.1
Design
Elevated structures supporting rotating machinery shall generally be
designed in accordance with German Standard DIN 4024
An alternative standard may be used subject to PTT/CONSULTANT
approval.
Analysis may be by 3 dimensional finite element methods.
Short circuit couplers, vacuum tension, oil whirl frequency, rotor critical
speeds and background vibration shall be considered.
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
7.4.2
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 10 of 11
REV: D2
Machine Shafts
Machine shaft bearings shall, whenever possible be located directly over
transverse supports.
7.4.3
Beams and Slabs
Beams and slabs shall not be of excessive span and corner rigidity shall be
taken into account.
7.4.4
Rigidity
The upper table and foundation base slab shall be rigid in the horizontal
plane.
7.4.5
Weight of Foundation Base Slab
The foundation base slab shall not weigh less than the combined supported
weight of the upper table, columns, walls and machines (including base
plates).
7.5
Differential Temperature
In the absence of more exact information for reinforced concrete a
temperature increase of 20°C shall be assumed for uniform heating of the
tabletop compared with the base slab.
For shrinkage of the tabletop, a temperature drop of 10°C compared with
the base slab shall be assumed.
Local temperature gradients across structural members shall be taken into
account.
7.6
Minimum Applied Loading
Structural members not subject to external loading shall be designed for a
static equivalent force equal to 50% of their dead load vertically or
horizontally, provided setting up loads do not govern.
8.0
SOILS DATA
8.1
Soil Bearing Foundations
The following soils information should be available for soil bearing
foundations: E
-
Dynamic Modulus of Elasticity of the soil
µ
-
Poisson’s Ratio
DESIGN OF MACHINE
FOUNDATIONS
SPECIFICATION
PTT PUBLIC COMPANY LIMITED
ENGINEERING STANDARD
SPC 0804.02-40.11
Page 11 of 11
REV: D2
Cu -
The coefficient of elastic uniform compression of the soil
Cø soil
The coefficient of elastic non-uniform compression of the
CT -
The coefficient of elastic uniform shear
Cψ -
The coefficient of elastic non-uniform shear
When values for Cø, CT and Cψ are not available the following assumptions
shall be made:
8.2
Cø -
2 Cu
CT -
0.5 Cu
Cψ -
0.75 Cu
Piled Foundations
The following information shall be available for piled foundations: -
9.0
The horizontal and vertical dynamic stiffness of a single pile
The horizontal and vertical dynamic stiffness of pile groups
An assessment of soil mass participation
ANTI-VIBRATION MOUNTINGS
When it is considered that an acceptable design cannot be achieved with a
foundation consisting of a soil-bearing block then consideration shall be
given to improving the dynamic characteristics by introducing anti-vibration
mountings.
10.0
ENVIRONMENTAL REQUIREMENTS
Considerations shall be given to the effect of noise and vibration generated
by the machine/foundation system on both people in the vicinity and any
nearby sensitive equipment to which reference shall be made to the Health
and Safety Regulations.