Possible Tension values for SEFAR® PET high-modulus mesh Headquarters mm* N/cm 0.553 50 0.613 45 0.691 80 70 70 40 0.912 35 30 70 70 64 64 55 64 55 64 55 64 55 48 20 1.750 15 2.455 10 40 40 40 25 1.340 48 48 70 34 40 34 34 34 31 34 31 31 31 32 43 45 48 51 54 61 64 68 73 The stated values are in [N/cm] according to DIN 16611 (screen printing standard) and measured using SEFAR® Tensocheck 100. The above values refer to tensions measured after stretching only (before gluing to the frame). These values are valid for dimensions of 1x1m. Larger formats will show a reduction of approx 4% every 0,5 m of additional shank length. Tensioning system requirements In view to obtain the above values, the performance of your tensioning system should be: –Stretching clamps SEFAR® 2, SEFAR® 3A or any other system that guarantees even and balanced tension. –A mesh clamping system that does not allow the mesh to slip, even under high tensions. It should be regularly cleaned and exempted of contaminants such as oil and dirt. –Tensioning clamps should be regularly checked in view to avoid sharp edges which could damage the mesh. –High humidity and high temperature could have influences on stretching performances. This may lead to difficulties during the stretching process. 31 34 31 *Protec STG 75 NA 4PD01081 EN 08/2012 55 48 40 55 1.086 Sefar AG Hinterbissaustrasse 12 9410 Heiden Switzerland Phone +41 71 898 57 00 Fax +41 71 898 57 21 [email protected] www.sefar.com Nominal thread diametre µm 70 80 80 70 0.786 80 27 27 27 77 81 90 95 100 110 120 130 140 150 165 180 190 mesh-count/cm Stretching process / Relaxation: Loss of tension after gluing process Tensioning process lasts up to 3 minutes until the desirable tension is achieved. Waiting time approx 3 to 5 minutes before gluing the mesh on the frame, the loss of tension after 24 hours will be 10 to 20% for respectively, coarse and fine meshes (any other parameters such as frame deformation are not taken in account). Other causes of loss of tension: –Poor frame characteristics (profile, material…) –Not adequate frame pre-tension –Quality of the adhesive –High humidity Waver: It is exclusively in written agreements that we provide our customers with warrants and representations as to the technical contained specifications and/or the fitness for any particular purpose. The facts and figures herein are carefully compiled to the best of our knowledge, but they are intended for general informational purposes only. Current data available on www.sefar.com Subsidiaries Sefar Maissa S.A. 08440 Cardedeu (Barcelona), Spain Phone +34 93 844 47 10 Fax +34 93 844 47 20 Sefar Inc. Buffalo, New York 14043, USA Phone +1 800 995 0531 Fax +1 716 685 9469 Sefar S.A. de C.V. 54080 Tlalnepantla, Estado de México, México Phone +52 55 5394 8689 Fax +52 55 5319 0358 Sefar Printing Solutions Ltda. 09895-003 São Bernardo do Campo, Brazil Phone +55 11 4390 6300 Fax +55 11 4390 6301 Sefar Singapore Pte. Ltd. 159 Kampong Ampat #05-02 KA Place, Singapore 368328 Phone +65 6299 9092 Fax +65 6299 6359 Sefar Filtration (India) Pvt. Ltd. Val Bhiwandi 421302, Dist. Thane, India Phone +91 2522 2940 34/35/36 Fax +91 2522 2940 37 Sefar Printing Solutions (Shanghai) Co. Ltd. Shanghai 201108, China Phone +86 21 6442 6800 Fax +86 21 6442 6866 Sefar Trading (Shenzhen) Co. Ltd. 518048 Futian District Shenzhen, China Phone +86 755 3398 3868 Fax +86 755 3398 3863 Sefar (International) AG Kwai Fong N.T., Hong Kong Phone +852 2650 0581 Fax +852 2638 0580 Sefar Co. Ltd. Suehiro-cho, Kita-ku Osaka, Japan 530-0053 Phone +81 6 4709 1070 Fax +81 6 4709 1071 Sefar Pty Ltd 3043 Tullamarine, Victoria, Australia Phone +61 3 9330 1122 Fax +61 3 9335 2592 Possible Tension values for SEFAR® PA polyamide mesh Headquarters mm* N/cm 0.553 50 0.613 45 0.691 Nominal thread diametre µm 90 100 40 70 60 90 0.786 35 30 1.086 25 1.340 20 Subsidiaries 70 80 0.912 60 70 60 35 50 60 35 44 1.750 15 2.455 10 38 38 35 30 35 30 30 35 30 30 30 32 36 40 43 48 54 61 68 *Protec STG 75 NA The stated values are in [N/cm] ac­cord­ ing to DIN 16611 (screen printing stand­ ard) and measured using SEFAR® Tensocheck 100. The above values refer to tensions measured after stretching only (before gluing to the frame). These values are valid for dimensions of 1x1m. It is not general practice to use frames larger than this with polyamide mesh. 4PD01111 EN 08/2012 Sefar AG Hinterbissaustrasse 12 9410 Heiden Switzerland Phone +41 71 898 57 00 Fax +41 71 898 57 21 [email protected] www.sefar.com Tensioning system requirements In view to obtain the above values, the performance of your tensioning system should be: –Stretching clamps SEFAR® 2, SEFAR® 3A or any other system that guarantees even and balanced tension. –A mesh clamping system that does not allow the mesh to slip, even under high tensions. It should be regularly cleaned and exempted of contaminants such as oil and dirt. –Tensioning clamps should be regularly checked in view to avoid sharp edges which could damage the mesh. –High humidity and high temperature could have influences on stretching performances. This may lead to diffi­culties during the stretching process. 77 90 100 110 120 130 140 150 165 180 200 mesh-count/cm Stretching procress / Relaxation: Tensioning process lasts up to 3 minutes until the desirable tension is achieved. Waiting time approx. 3 to 5 minutes before gluing the mesh on the frame. The loss of tension after 24 hours will be 20 to 30% for respectively, coarse and fine meshes (any other parameters such as frame deformation are not taken in account). Other causes of loss of tension: –Poor frame characteristics (profile, material…) –Not adequate frame pre-tension –Quality of the adhesive –High humidity Waver: It is exclusively in written agreements that we provide our customers with warrants and representations as to the technical contained specifications and/or the fitness for any particular purpose. The facts and figures herein are carefully compiled to the best of our knowledge, but they are intended for general informational purposes only. Current data available on www.sefar.com Sefar Maissa S.A. 08440 Cardedeu (Barcelona), Spain Phone +34 93 844 47 10 Fax +34 93 844 47 20 Sefar Inc. Buffalo, New York 14043, USA Phone +1 800 995 0531 Fax +1 716 685 9469 Sefar S.A. de C.V. 54080 Tlalnepantla, Estado de México, México Phone +52 55 5394 8689 Fax +52 55 5319 0358 Sefar Printing Solutions Ltda. 09895-003 São Bernardo do Campo, Brazil Phone +55 11 4390 6300 Fax +55 11 4390 6301 Sefar Singapore Pte. Ltd. 159 Kampong Ampat #05-02 KA Place, Singapore 368328 Phone +65 6299 9092 Fax +65 6299 6359 Sefar Filtration (India) Pvt. Ltd. Val Bhiwandi 421302, Dist. Thane, India Phone +91 2522 2940 34/35/36 Fax +91 2522 2940 37 Sefar Printing Solutions (Shanghai) Co. Ltd. Shanghai 201108, China Phone +86 21 6442 6800 Fax +86 21 6442 6866 Sefar Trading (Shenzhen) Co. Ltd. 518048 Futian District Shenzhen, China Phone +86 755 3398 3868 Fax +86 755 3398 3863 Sefar (International) AG Kwai Fong N.T., Hong Kong Phone +852 2650 0581 Fax +852 2638 0580 Sefar Co. Ltd. Suehiro-cho, Kita-ku Osaka, Japan 530-0053 Phone +81 6 4709 1070 Fax +81 6 4709 1071 Sefar Pty Ltd 3043 Tullamarine, Victoria, Australia Phone +61 3 9330 1122 Fax +61 3 9335 2592 Possible Tension values for SEFAR® PME Headquarters mm* N/cm 0.581 47.5 0.613 45 0.651 42.5 0.691 40 0.734 37.5 0.786 35 0.845 32.5 0.912 30 0.975 27.5 Nominal thread diametre µm 48 40 35 35 30 35 Sefar Inc. Buffalo, New York 14043, USA Phone +1 800 995 0531 Fax +1 716 685 9469 30 54 61 71 100 The stated values are in [N/cm] accord­ ing to DIN 16611 (screen printing standard) and measured using SEFAR® Tensocheck 100. The above values refer to tensions measured after stretching only (before gluing to the frame). These values are valid for dimensions of 1x1m. Larger formats will show a reduction of approx 4% every 0,5 m of additional shank length. Tensioning system requirements In view to obtain the above values, the performance of your tensioning system should be: –Stretching clamps SEFAR® 2, SEFAR® 3A or any other system that guarantees even and balanced tension. –A mesh clamping system that does not allow the mesh to slip, even under high tensions. It should be regularly cleaned and exempted of contaminants such as hardened glue oil and dirt. –Tensioning clamps should be regularly checked in view to avoid sharp edges which could damage the mesh. –High humidity and high temperature could have influences on stretching performances. This may lead to difficulties during the stretching process. 110 Subsidiaries Sefar Maissa S.A. 08440 Cardedeu (Barcelona), Spain Phone +34 93 844 47 10 Fax +34 93 844 47 20 30 30 *Protec STG 75 NA 4PD01265 EN 08/2012 Sefar AG Hinterbissaustrasse 12 9410 Heiden Switzerland Phone +41 71 898 57 00 Fax +41 71 898 57 21 [email protected] www.sefar.com 120 130 140 150 mesh-count/cm Stretching process / Relaxation: Loss of tension after gluing process Tensioning process lasts up to 3 minutes until the desirable tension is achieved. Waiting time approx 3 to 5 minutes before gluing the mesh on the frame, the loss of tension after 24 hours will be 10 to 15% for respectively, coarse and fine meshes (any other parameters such as frame deformation are not taken in account). Other causes of loss of tension: –Poor frame characteristics (profile, material…) –Not adequate frame pre-tension –Quality of the adhesive –High humidity Waver: It is exclusively in written agreements that we provide our customers with warrants and representations as to the technical contained specifications and/or the fitness for any particular purpose. The facts and figures herein are carefully compiled to the best of our knowledge, but they are intended for general informational purposes only. Current data available on www.sefar.com Sefar S.A. de C.V. 54080 Tlalnepantla, Estado de México, México Phone +52 55 5394 8689 Fax +52 55 5319 0358 Sefar Printing Solutions Ltda. 09895-003 São Bernardo do Campo, Brazil Phone +55 11 4390 6300 Fax +55 11 4390 6301 Sefar Singapore Pte. Ltd. 159 Kampong Ampat #05-02 KA Place, Singapore 368328 Phone +65 6299 9092 Fax +65 6299 6359 Sefar Filtration (India) Pvt. Ltd. Val Bhiwandi 421302, Dist. Thane, India Phone +91 2522 2940 34/35/36 Fax +91 2522 2940 37 Sefar Printing Solutions (Shanghai) Co. Ltd. Shanghai 201108, China Phone +86 21 6442 6800 Fax +86 21 6442 6866 Sefar Trading (Shenzhen) Co. Ltd. 518048 Futian District Shenzhen, China Phone +86 755 3398 3868 Fax +86 755 3398 3863 Sefar (International) AG Kwai Fong N.T., Hong Kong Phone +852 2650 0581 Fax +852 2638 0580 Sefar Co. Ltd. Suehiro-cho, Kita-ku Osaka, Japan 530-0053 Phone +81 6 4709 1070 Fax +81 6 4709 1071 Sefar Pty Ltd 3043 Tullamarine, Victoria, Australia Phone +61 3 9330 1122 Fax +61 3 9335 2592
