NEWCO® Forged Steel Valves Technical Data TC9308-4 All the information contained in this manual is the exclusive property of Cameron. Any reproduction or use of the calculations, drawings, photographs, procedures or instructions, either expressed or implied, is forbidden without the written permission of Cameron or its authorized agent. Initial Release 01 August 2013 Produced by Technical Publications, Houston, TX, USA © 2013 Cameron TC9308-4 2 PREFACE The procedures included in this book are to be performed in conjunction with the requirements and recommendations outlined in API Specifications. Any repairs to the equipment covered by this book should be done by an authorized Cameron service representative. Cameron will not be responsible for loss or expense resulting from any failure of equipment or any damage to any property or death or injury to any person resulting in whole or in part from repairs performed by anyone other than authorized Cameron personnel. Such unauthorized repairs shall also serve to terminate any contractual or other warranty, if any, on the equipment and may also result in equipment no longer meeting applicable requirements. File copies of this manual are maintained. Revisions and/or additions will be made as deemed necessary by Cameron. The drawings in this book are not drawn to scale, but the dimensions shown are accurate. This book covers Cameron products. Cameron P.O. Box 1212 Houston, Texas 77251-1212 713-939-2211 http://www.c-a-m.com TC9308-4 3 NOTES: TC9308-4 4 TABLE OF CONTENTS Flange Dimensions - ASME B16.5.......................................................................................6 Pressure Temperature Ratings - ASME B16.34 - 2004 (Standard)....................................10 Pressure Temperature Ratings - ASME B16.34 - 2004 (Metric).........................................13 Overview..............................................................................................................................16 TC9308-4 I. Forged Steel Bolted and Welded Bonnet Gate Valves.............................................19 Sizes: 1/4” to 3” • Pressure Class: 150 to 4500 II. Forged Steel Bolted and Welded Bonnet Globe Valves...........................................33 Sizes: 1/2” to 2” • Pressure Class: 150 to 4500 III. Forged Steel Bolted and Welded Bonnet Check Valves...........................................47 Sizes: 1/2” to 2” • Pressure Class: 150 to 1500 IV. Forged Steel Cv Values Gates, Globes, Checks..........................................................56 V. How to Order All Cameron’s NEWCO Products........................................................58 VI. Industry Standards Typically Used in Valve Manufacturing.....................................61 5 FLANGE DIMENSIONS - ASME B16.5 Raised Face Class 150 and 300 B B1 16 C D A C D C A D A B1 16 1 16 Raised Face Class 600 to 2500 B B 1 4 C D A C D C A D A B 1 4 1 4 RTJ Class 600 to 2500 B B E B E E TC9308-4 6 F C D F A C F D C A D A Flange Dimensions in Inches Class 150 Size In. mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A 3.5 89 3.88 98 4.25 108 4.62 117 5 127 6 152 B 0.44 11.58 0.5 13 0.55 14.5 0.62 16 0.69 17.5 0.75 19.5 C 1.38 34.9 1.69 42.9 2 50.8 2.5 68.5 2.88 73 3.62 92.1 Ring Joint Facing D 2.38 60.3 2.75 69 3.12 79.4 3.5 88.9 3.88 98.4 4.75 120.6 C F E - - - Ring No. - Bolt Holes Size 0.62 16 0.62 16 0.62 16 0.62 16 0.62 16 0.75 19 No. 4 4 4 4 4 4 Flange Dimensions in Inches Class 300 Size In. mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 TC9308-4 A 3.75 95 4.62 117 4.88 124 5.25 133 6.12 156 6.5 165 B 0.56 14.5 0.62 16 0.69 17.5 0.75 19.5 0.81 21 0.88 22.5 C 1.38 34.9 1.69 42.9 2 50.8 2.5 68.5 2.88 73 3.62 92.1 Ring Joint Facing D 2.62 66.7 3.25 82.5 3.5 88.9 3.88 98.4 4.5 114.3 5 127 C F E - - - 7 Ring No. - Bolt Holes Size 0.62 16 0.75 19 0.75 19 0.75 19 0.88 22.5 0.75 19 No. 4 4 4 4 4 8 Flange Dimensions in Inches Class 600 Size In. mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A 3.75 95 4.62 117 4.88 124 5.25 133 6.12 156 6.5 165 B 0.56 14.5 0.62 16 0.69 17.5 0.81 21 0.88 22.5 1 25.5 C 1.38 34.9 1.69 42.9 2 50.8 2.5 63.5 2.88 73 3.62 92.1 Ring Joint Facing D 2.62 66.7 3.25 82.5 3.5 88.9 3.88 98.4 4.5 114.3 5 127 C F E 2 51 2.5 63.5 2.75 70 3.12 79.5 3.56 90.5 4.25 108 1.34 34.14 1.68 42.88 2 50.8 2.38 60.32 2.69 68.28 3.25 82.55 0.22 5.6 0.25 6.3 0.25 6.3 0.25 6.3 0.25 6.3 0.31 79 Ring No. R 11 R 13 R 16 R 18 R 20 R 23 Bolt Holes Size 0.62 16 0.75 19 0.75 19 0.75 19 0.88 22.5 0.75 19 No. 4 4 4 4 4 8 Flange Dimensions in Inches Class 1500 Size In. mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 TC9308-4 A 4.75 121 5.12 130 5.88 149 6.25 159 7 178 8.5 216 B 0.88 22.5 1 22.5 1.12 29 1.12 29 1.25 32 1.5 38.5 C 1.38 34.9 1.69 42.9 2 50.8 2.5 63.5 2.88 73 3.62 92.1 Ring Joint Facing D 3.25 82.5 3.5 88.9 4 101.6 4.38 111.1 4.88 123.8 6.5 165.1 C F E 2.38 60.5 2.62 66.5 2.81 71.5 3.19 81 3.62 92 4.88 124 1.56 39.67 1.75 44.45 2 50.8 2.37 60.32 2.68 68.28 3.75 95.25 0.25 6.3 0.25 6.3 0.25 6.3 0.25 6.3 0.25 6.3 0.31 7.9 8 Ring No. R 12 R 14 R 16 R 18 R 20 R 24 Bolt Holes Size 0.88 22.5 0.88 22.5 1 25.5 1 25.5 1.12 28.5 1 25.5 No. 4 4 4 4 4 8 Flange Dimensions in Inches Class 2500 Size In. mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 TC9308-4 A 5.25 133.5 5.5 139.5 6.25 159 7.25 184 8 203 9.25 235 B 1.19 30.5 1.25 32 1.38 35 1.5 38.5 1.75 44.5 2 51 C 1.38 34.9 1.69 42.9 2 50.8 2.5 63.5 2.88 73 3.62 92.1 Ring Joint Facing D 3.5 88.9 3.75 95.3 4.25 108 5.12 130.2 5.75 146.1 6.75 171.5 C F E 2.56 65 2.88 73.2 3.25 82.5 4 101.6 4.5 114.3 5.25 133.4 1.68 42.88 2 50.8 2.37 60.32 2.84 72.24 3.25 82.55 4 101.6 0.25 6.3 0.25 6.3 0.25 6.3 0.31 7.9 0.31 7.9 0.31 7.9 9 Ring No. R 13 R 16 R 18 R 21 R 23 R 26 Bolt Holes Size 0.88 22.5 0.88 22.5 1 25.5 1.12 28.5 1.25 32 1.12 28.5 No. 4 4 4 4 4 8 PRESSURE TEMPERATURE RATINGS ASME B16.34 - 2004 (STANDARD) Class 150 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 A105* LF2* F11+ F22+ F5 F9 F91 285 290 290 290 290 290 290 260 260 260 260 260 260 260 230 230 230 230 230 230 230 200 200 200 200 200 200 200 170 170 170 170 170 170 170 140 140 140 140 140 140 140 125 125 125 125 125 125 125 110 110 110 110 110 110 110 95 95 95 95 95 95 95 80 80 80 80 80 80 80 65 65 65 65 65 65 65 50 50 50 50 50 50 50 35 35 35 35 35 35 35 1000 1050 1100 1150 1200 20 20 20 20 20 20 20 20** 20** 20** 20** 20 20** 20** 20** 20** 20 20** 20** 20 20** 20** 20 Class 300 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 A105* LF2* F11+ F22+ 740 740 750 750 750 750 750 680 680 750 750 750 750 750 655 655 720 730 730 730 730 635 635 695 705 705 705 705 605 605 665 665 665 665 665 570 570 605 605 605 605 605 550 550 590 590 590 590 590 530 530 570 570 570 570 570 505 505 530 530 530 530 530 410 410 510 500 510 510 510 320 320 485 485 485 4185 485 230 230 450 450 375 450 450 135 135 320 385 275 375 385 F5 F9 F91 1000 1050 1100 1150 1200 85 85 215 265 200 255 365 145 175 145 170 360 95 110 100 115 300 65 70 60 75 225 40 40 35 50 145 Class 600 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 A105* LF2* F11+ F22+ 1480 1480 1500 1500 1500 1500 1500 1360 1360 1500 1500 1470 1500 1500 1310 1310 1445 1455 1400 1455 1455 1265 1265 1385 1410 1335 1410 1410 1205 1205 1330 1330 1290 1330 1330 1135 1135 1210 1210 1210 1210 1210 1100 1100 1175 1175 1175 1175 1175 1060 1060 1135 1135 1135 1135 1135 1015 1015 1065 1065 1065 1065 1065 825 825 1015 1015 1015 1015 1015 640 640 975 975 975 975 975 460 460 900 900 745 900 900 275 275 640 755 550 755 775 F5 F9 F91 1000 1050 1100 1150 1200 170 170 430 535 400 505 725 290 350 290 345 720 190 220 190 225 605 130 135 125 150 445 80 80 70 105 290 Class 800 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 A105* LF2* F11+ F22+ 1974 1974 2000 2000 2000 2000 2000 1810 1810 2000 2000 1964 2000 2000 1747 1747 1925 1942 1876 1942 1942 1689 1689 1849 1880 1782 1880 1880 1609 1609 1774 1774 1724 1774 1774 1515 1515 1614 1614 1614 1614 1614 1467 1467 1569 1569 1569 1569 1569 1414 1414 1515 1515 1515 1515 1515 1352 1352 1419 1419 1419 1419 1419 1098 1098 1355 1355 1355 1355 1355 850 850 1298 1298 1298 1298 1298 613 613 1200 1200 995 1200 1200 365 365 850 1025 733 1005 1032 F5 F9 F91 TC9308-4 10 1000 1050 1100 1150 1200 227 227 577 712 530 675 968 383 467 383 458 960 257 293 257 302 805 173 182 165 200 595 110 110 93 138 383 Class 900 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 A105* LF2* F11+ F22+ F5 F9 F91 2220 2220 2250 2250 2250 2250 2250 2035 2035 2250 2250 2210 2250 2250 1965 1965 2165 2185 2100 2185 2185 1900 1900 2080 2115 2005 2115 2115 1810 1810 1995 1995 1940 1995 1995 1705 1705 1815 1815 1815 1815 1815 1650 1650 1765 1765 1765 1765 1765 1590 1590 1705 1705 1705 1705 1705 1520 1520 1595 1595 1595 1595 1595 1235 1235 1525 1525 1525 1525 1525 955 955 1460 1460 1460 1460 1460 690 690 1350 1350 1120 1350 1350 410 410 955 1160 825 1130 1160 255 255 650 800 595 760 1090 430 525 430 515 1080 290 330 290 340 905 195 205 185 225 670 125 125 105 155 430 Class 1500 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 A105* LF2* F11+ F22+ 3705 3705 3750 3750 3750 3750 3750 3395 3395 3750 3750 3680 3750 3750 3270 3270 3610 3640 3495 3640 3640 3170 3170 3465 3530 3345 3530 3530 3015 3015 3325 3325 3230 3325 3325 2840 2840 3025 3025 3025 3025 3025 2745 2745 2940 2940 2940 2940 2940 2665 2665 2840 2840 2840 2840 2840 2535 2535 2660 2660 2660 2660 2660 2055 2055 2540 2540 2540 2540 2540 1595 1595 2435 2435 2435 2435 2435 1150 1150 2245 2245 1870 2245 2245 685 685 1595 1930 1370 1885 1930 430 430 1080 1335 995 1270 1820 F5 F9 F91 720 875 720 855 1800 480 550 480 565 1510 325 345 310 375 1115 205 205 170 255 720 Class 1690 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 A105* LF2* F11+ F22+ F5 F9 F91 4173 4173 4225 4225 4225 4225 4225 3824 3824 4225 4225 4146 4225 4225 3684 3684 4067 4102 3939 4102 4102 3571 3571 3904 3977 3768 3977 3977 3397 3397 3746 3746 3639 3746 3746 3199 3199 3408 3408 3408 3408 3408 3093 3093 3313 3313 3313 3313 3313 2999 2999 3199 3199 3199 3199 3199 2857 2857 2996 2996 2996 2996 2996 2316 2316 2861 2861 2861 2861 2861 1796 1796 2744 2744 2744 2744 2744 1295 1295 2530 2530 2107 2530 2530 772 772 1796 2175 1544 2124 2175 484 484 1217 1505 1120 1431 2050 811 985 811 964 2028 541 619 541 637 1701 367 388 349 423 1256 232 232 192 288 811 Class 2500 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 A105* LF2* F11+ F22+ 6170 6170 6250 6250 6250 6250 6250 5655 5655 6250 6250 6135 6250 6250 5450 5450 6015 6070 5830 6070 6070 5280 5280 5775 5880 5570 5880 5880 5025 5025 5540 5540 5385 5540 5540 4730 4730 5040 5040 5040 5040 5040 4575 4575 5905 4905 4905 4905 4905 4425 4425 4730 4730 4730 4730 4730 4230 4230 4430 4430 4430 4430 4430 3430 3430 4230 4230 4230 4230 4230 2655 2655 4060 4060 4060 4060 4060 1915 1915 3745 3745 3115 3745 3745 1145 1145 2655 3220 2285 3145 3220 715 715 1800 2230 1655 2115 3030 F5 F9 F91 TC9308-4 11 1200 1455 1200 1430 3000 800 915 800 945 2515 545 570 515 630 1855 345 345 285 430 1200 Class 2680 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 A105* LF2* F11+ F22+ F5 F9 F91 6615 6615 6700 6700 6700 6700 6700 6063 6063 6700 6700 6576 6700 6700 5843 5843 6448 6507 6249 6507 6507 5660 5660 6191 6303 5971 6303 6303 5386 5386 5938 5938 5772 5938 5938 5071 5071 5403 5403 5403 5403 5403 4905 4905 5258 5258 5258 5258 5258 4743 4743 5071 5071 5071 5071 5071 4534 4534 4749 4749 4749 4749 4749 3677 3677 4534 4534 4534 4534 4534 2847 2847 4352 4352 4352 4352 4352 2054 2054 4015 4015 3339 4015 4015 1227 1227 2847 3452 2450 3371 3452 766 766 1930 2390 1775 2267 3248 1286 1560 1286 1533 3216 858 981 858 1013 2696 584 611 552 675 1989 369 369 306 461 1286 Class 4500 ºF / PSI -20 to 100 200 300 400 500 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 A105* LF2* F11+ F22+ 11110 11110 11250 11250 11250 11250 11250 10185 10185 11250 11250 11040 11250 11250 9815 9815 10830 10925 10490 10925 10925 9505 9505 10400 10585 10030 10585 10586 9040 9040 9965 9965 9690 9965 9965 8515 8515 9070 9070 9070 9070 9070 8240 8240 8825 8825 8825 8825 8825 7960 7960 8515 8515 8515 8515 8515 7610 7610 7970 7970 7970 7970 7970 6170 6170 7610 7610 7610 7610 7610 4785 4785 7305 7305 7305 7305 7305 3455 3455 6740 6740 5605 6740 6740 2055 2055 4785 5795 4115 5655 5795 1285 1285 3240 4010 2985 3805 5450 F5 F9 F91 2160 2625 2160 2570 5400 1440 1645 1440 1695 4525 975 1030 925 1130 3345 615 615 515 770 2160 * Not recommended for prolonged use above 800° F. + Not recommended for prolonged use above 1100° F. ** For weld end valves only. Flanged end ratings terminate at 1000° F. Note: Packing, gasket or bolting may limit temperature. Please advise service temperature if above 1000° F. Ratings from ASME B16.34 standard class valves. Special class weld end valves to ASME B16.34 are available on special order. TC9308-4 12 PRESSURE TEMPERATURE RATINGS ASME B16.34 - 2004 (METRIC) Class 150 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 19.6 19.6 19.8 19.8 20.0 20.0 20.0 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 17.7 17.7 17.7 17.7 17.7 17.7 17.7 15.8 15.8 15.8 15.8 15.8 15.8 15.8 13.8 13.8 13.8 13.8 13.8 13.8 13.8 12.1 12.1 12.1 12.1 12.1 12.1 12.1 10.2 10.2 10.2 10.2 10.2 10.2 10.2 8.4 8.4 8.4 8.4 8.4 8.4 8.4 7.4 7.4 7.4 7.4 7.4 7.4 7.4 6.5 6.5 6.5 6.5 6.5 6.5 6.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 4.6 4.6 4.6 4.6 4.6 4.6 4.6 3.7 3.7 3.7 3.7 3.7 3.7 3.7 2.8 2.8 2.8 2.8 2.8 2.8 2.8 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.4** 1.1** 1.1** 0.9** 1.4** 1.4** Class 300 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 51.1 51.1 51.7 51.7 51.7 51.7 51.7 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 46.6 46.6 51.5 51.5 51.5 51.5 51.5 45.1 45.1 49.7 50.3 50.3 50.3 50.3 43.8 43.8 48.0 48.6 48.6 48.6 48.6 41.9 41.9 46.3 46.3 46.3 46.3 46.3 39.8 39.8 42.9 42.9 42.9 42.9 42.9 37.6 37.6 40.3 40.3 40.3 40.3 40.3 36.4 36.4 38.9 38.9 38.9 38.9 38.9 34.7 34.7 36.5 36.5 36.5 36.5 36.5 28.8 28.8 35.2 35.2 35.2 35.2 35.2 23.0 23.0 33.7 33.7 33.7 33.7 33.7 17.4 17.4 31.7 31.7 27.9 31.7 31.7 11.8 11.8 25.7 28.2 21.4 28.2 28.2 5.9 5.9 14.9 18.4 13.7 17.5 25.2 8.8 10.5 8.9 10.5 24.0 6.1 6.9 6.2 7.2 19.5 4.3 4.5 4.0 5.0 14.6 2.8 2.8 2.4 3.5 9.9 Class 600 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 102.1 102.1 103.4 103.4 103.4 103.4 103.4 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 93.2 93.2 103.0 103.0 103.0 103.0 103.0 90.2 90.2 99.5 100.3 100.3 100.3 100.3 87.6 87.6 95.9 97.2 97.2 97.2 97.2 83.9 83.9 92.7 92.7 92.7 92.7 92.7 79.6 79.6 85.7 85.7 85.7 85.7 85.7 75.1 75.1 80.4 80.4 80.4 80.4 80.4 72.7 72.7 77.6 77.6 77.6 77.6 77.6 69.4 69.4 73.3 73.3 73.3 73.3 73.3 57.5 57.5 70.0 70.0 70.0 70.0 70.0 46.0 46.0 67.7 67.7 67.7 67.7 67.7 34.9 34.9 63.4 63.4 55.7 63.4 63.4 23.5 23.5 51.5 56.5 42.8 56.5 56.5 11.8 11.8 29.8 36.9 27.4 35.0 50.0 17.6 21.1 17.8 20.9 47.9 12.2 13.8 12.5 14.4 39.0 8.5 8.9 8.0 9.9 29.2 5.7 5.7 4.7 7.1 19.9 Class 800 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 136.0 136.0 137.8 137.8 137.8 137.8 137.8 TC9308-4 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 124.7 124.7 137.8 137.8 135.3 137.8 137.8 120.4 120.4 132.6 133.8 128.6 133.8 133.8 116.3 116.3 127.4 129.5 122.8 129.5 129.5 110.8 110.8 122.2 122.2 118.8 122.2 122.2 104.4 104.4 111.2 111.2 111.2 111.2 111.2 101.1 101.1 108.1 108.1 108.1 108.1 108.1 97.4 97.4 104.4 104.4 104.4 104.4 104.4 93.1 93.1 97.7 97.7 97.7 97.7 97.7 75.7 75.7 93.4 93.4 93.4 93.4 93.4 58.6 58.6 89.5 89.5 89.5 89.5 89.5 42.3 42.3 82.7 82.7 68.6 82.7 82.7 25.2 25.2 58.6 70.6 50.5 69.3 71.1 15.6 15.6 39.7 49.0 36.5 46.5 66.7 26.4 32.2 26.4 31.6 66.2 17.7 20.2 17.7 20.8 55.5 11.9 12.5 11.4 13.8 41.0 7.6 7.6 6.4 9.5 26.4 13 Class 900 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 153.2 153.2 155.1 155.1 155.1 155.1 155.1 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 139.8 139.8 154.4 154.6 154.6 154.6 154.6 135.2 135.2 149.2 150.6 150.6 150.6 150.6 131.4 131.4 143.9 145.8 145.8 145.8 145.8 125.8 125.8 139.0 139.0 139.0 139.0 139.0 119.5 119.5 128.6 128.6 128.6 128.6 128.6 112.7 112.7 120.7 120.7 120.7 120.7 120.7 109.1 109.1 116.5 116.5 116.5 116.5 116.5 104.2 104.2 109.8 109.8 109.8 109.8 109.8 86.3 86.3 105.1 105.1 105.1 105.1 105.1 69.0 69.0 101.4 101.4 101.4 101.4 101.4 52.3 52.3 95.1 95.1 83.6 95.1 95.1 35.3 35.3 77.2 84.7 64.1 84.7 84.7 17.7 17.7 44.7 55.3 41.1 52.5 75.2 26.4 31.6 26.7 31.4 71.8 18.3 20.7 18.7 21.5 58.5 12.8 13.4 12.0 14.9 43.8 8.5 8.5 7.1 10.6 29.8 Class 1500 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 255.3 255.3 258.6 258.6 258.6 258.6 258.6 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 233.0 233.0 257.4 257.6 257.6 257.6 257.6 225.4 225.4 248.7 250.8 250.8 250.8 250.8 219.0 219.0 239.8 243.4 243.4 243.4 243.4 209.7 209.7 231.8 231.8 231.8 231.8 231.8 199.1 199.1 214.4 214.4 214.4 214.4 214.4 187.8 187.8 201.1 201.1 201.1 201.1 201.1 181.8 181.8 194.1 194.1 194.1 194.1 194.1 173.6 173.6 183.1 183.1 183.1 183.1 183.1 143.8 143.8 175.1 175.1 175.1 175.1 175.1 115.0 115.0 169.0 169.0 169.0 169.0 169.0 87.2 87.2 158.2 158.2 139.3 158.2 158.2 58.8 58.8 128.6 140.9 106.9 140.9 140.9 29.5 29.5 74.5 92.2 68.6 87.5 125.5 44.0 52.6 44.4 52.3 119.7 30.5 34.4 31.2 35.9 97.5 21.3 22.3 20.0 24.8 73.0 14.2 14.2 11.8 17.7 49.6 Class 1690 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 287.5 287.5 291.1 291.1 291.1 291.1 291.1 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 263.5 263.5 291.1 291.1 285.7 291.1 291.1 253.8 253.8 280.2 282.6 271.4 282.6 282.6 246.0 246.0 269.0 274.0 259.6 274.0 274.0 234.0 234.0 258.1 258.1 250.8 258.1 258.1 220.4 220.4 234.8 234.8 234.8 234.8 234.8 213.1 213.1 28.3 228.3 228.3 228.3 228.3 206.7 206.7 220.4 220.4 220.4 220.4 220.4 196.9 196.9 206.4 206.4 206.4 206.4 206.4 159.6 159.6 197.1 197.1 197.1 197.1 197.1 123.8 123.8 189.0 189.0 189.0 189.0 189.0 89.2 89.2 174.3 174.3 145.1 174.3 174.3 53.2 53.2 123.8 149.9 106.4 146.4 149.9 33.4 33.4 83.8 103.7 77.2 98.6 141.2 55.9 67.9 55.9 66.4 139.7 37.3 42.7 37.3 43.9 117.2 25.3 26.7 24.0 29.2 86.5 16.0 16.0 13.2 19.9 55.9 Class 2500 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 425.5 425.5 430.9 430.9 430.9 430.9 430.9 TC9308-4 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 388.3 388.3 429.0 429.4 429.4 429.4 429.4 375.6 375.6 414.5 418.2 418.2 418.2 418.2 365.0 365.0 399.6 405.4 405.4 405.4 405.4 349.5 349.5 386.2 386.2 386.2 386.2 386.2 331.8 331.8 357.1 357.1 357.1 357.1 357.1 313.0 313.0 335.3 335.3 335.3 335.3 335.3 303.1 303.1 323.2 323.2 323.2 323.2 323.2 289.3 289.3 304.9 304.9 304.9 304.9 304.9 239.7 239.7 291.6 291.6 291.6 291.6 291.6 191.7 191.7 281.8 281.8 281.8 281.8 281.8 145.3 145.3 263.9 263.9 232.1 263.9 263.9 97.9 97.9 214.4 235.0 178.2 235.0 235.0 49.2 49.2 124.1 153.7 114.3 145.8 208.9 73.4 87.7 74.0 87.1 199.5 50.9 57.4 51.9 59.8 162.5 35.5 37.2 33.3 41.4 121.7 23.6 23.6 19.7 29.5 82.7 14 Class 2680 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 455.7 455.7 461.6 461.6 461.6 461.6 461.6 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 417.7 417.7 461.6 461.6 453.1 461.6 461.6 402.6 402.6 444.3 448.3 430.6 448.3 448.3 390.0 390.0 426.6 434.3 411.4 434.3 434.3 371.1 371.1 409.1 409.1 397.7 409.1 409.1 349.4 349.4 372.2 372.2 372.2 372.2 372.2 337.9 337.9 362.3 362.3 362.3 362.3 362.3 326.8 326.8 349.4 349.4 349.4 349.4 349.4 312.4 312.4 327.2 327.2 327.2 327.2 327.2 253.3 253.3 312.4 312.4 312.4 312.4 312.4 196.1 196.1 299.9 299.9 299.9 299.9 299.9 141.5 141.5 276.6 276.6 230.1 276.6 276.6 84.5 84.5 196.1 237.8 168.8 232.3 237.8 52.8 52.8 132.9 164.7 122.3 156.2 223.8 88.6 107.5 88.6 105.6 221.6 59.1 67.6 59.1 69.8 185.7 40.2 42.1 38.0 46.5 137.0 25.4 25.4 21.1 31.7 88.6 Class 4500 ºC / BAR A105* LF2* F11+ F22+ F5 F9 F91 -29 to 38 765.9 765.9 775.7 775.7 775.7 775.7 775.7 100 150 200 250 300 350 375 400 425 450 475 500 538 575 600 625 650 699.0 699.0 772.2 773.0 773.0 773.0 773.0 676.1 676.1 746.2 752.8 752.8 752.8 752.8 657.0 657.0 719.4 729.8 729.8 729.8 729.8 629.1 629.1 694.8 694.8 694.8 694.8 694.8 597.3 597.3 642.6 642.6 642.6 642.6 642.6 563.5 563.5 603.3 603.3 603.3 603.3 603.3 545.5 545.5 581.8 581.8 581.8 581.8 581.8 520.8 520.8 548.5 548.5 548.5 548.5 548.5 431.5 431.5 524.7 524.7 524.7 524.7 524.7 345.1 345.1 507.0 507.0 507.0 507.0 507.0 261.5 261.5 474.8 474.8 417.8 474.8 474.8 176.3 176.3 385.9 423.0 320.7 423.0 423.0 88.6 88.6 223.4 276.6 205.7 262.4 375.8 132.0 157.9 133.3 156.8 359.1 91.6 103.3 93.5 107.7 292.5 63.9 66.9 59.9 74.5 219.1 42.6 42.6 35.5 53.2 148.9 * Not recommended for prolonged use above 425° C. + Not recommended for prolonged use above 600° C. ** For weld end valves only. Flanged end ratings terminate at 538° C. Note: Packing, gasket or bolting may limit temperature. Please advise service temperature if above 538° C. Ratings from ASME B16.34 standard class valves. Special class weld end valves to ASME B16.34 are available on special order. TC9308-4 15 OVERVIEW Valve and I.D. Tag Overview The identification tag displays all construction and tracking data regarding the respective valve on which it is attached. Below is a general overview of the identification tag components. I.D. tags are located under the handwheel nut. Globe and check valves will have a flow direction arrow on body for proper installation. I.D. Tag Material Flow Direction Pattern Size Pressure Class Cameron’s NEWCO 41 I.D. Tag Figure Number CE Mark Pattern Number Valve Type Body Material Nominal Valve Size Stem Material Disc Material Pressure Class Manufactured Date Factory Reference Number Seat Material Maximum Temperature Minimum Temperature Max. Press. @ Max. Temp. Design Specifications Pattern Max. Press. @ Min. Temp. TC9308-4 16 Cameron’s NEWCO 45 I.D. Tag Figure Number Pattern Valve Type CE Mark Body Material Pressure Class Stem Material Disc Material Nominal Valve Size Manufactured Date Seat Material Factory Reference Number Minimum Temperature Maximum Temperature Max. Press. @ Min. Temp. Max. Press. @ Max. Temp. Design Specifications Body/Bonnet Materials Cameron’s NEWCO® forged steel valves are available in stock in a wide range of body/ bonnet materials and optional trim materials. Listed below are some of the more popular materials. Additional materials are available. Please contact Cameron or your local distributor for details. NEWCO Material Designation Common Description ASTM Specs. FS Carbon Steel A105 Non-corrosive service water, oil and gases at temperatures between -20º F and +800º F. LF2 Low Temp. Carbon A350 Low temperature service between -50º F and +800º F. F11 1.25% Chrome and .5% Moly A182 Non-corrosive service water, oil and gases at temperatures between -20º F and +1100º F. F22 2.25% Chrome and 1% Moly A182 Non-corrosive service water, oil and gases at temperatures between -20º F and +1100º F. F5 5% Chrome and .5% Moly A182 Corrosive, non-corrosive or erosive service at temperatures between -20º F and +1200º F. F9 9% Chrome and 1% Moly A182 Corrosive, non-corrosive or erosive service at temperatures between -20º F and +1200º F. F91 9% Chrome, 1% Moly and V A182 Corrosive, non-corrosive or erosive service at temperatures between -20º F and +1200º F. F316 316 A182 Corrosive, cryogenic or high temperature service between -450º F and +1200º F. Body/Bonnet Material Service Limitations* * Limitations are per 2004 Edition of ASME B16.34. TC9308-4 17 Trim Materials The following are Cameron’s NEWCO standard trim designations: Wedge or Disc Facing (1) Stem Other Trim Parts (2) CR 13 CR 13 CR 13 CR 13 Non-corrosive applications. Steam, gas and general service to 700º F. Oil and oil vapor to 900º F. 8 HF CR 13 CR 13 CR 13 Steam, gas and general service to 1000º F. Standard trim for gate valves. Full Stellite 5 HF HF CR 13 CR 13 Premium trim service to 1200º F. Excellent for high pressure water and steam service. 4 316 10 316 316 316 316 Corrosive services to 850º F. Low temperature service standard for 316 SS valves. 4/2 316/Half Stellite 12 HF 316 316 316 4/3 316/Full Stellite 16 HF HF 316 316 5 Monel 9 NiCu NiCu NiCu NiCu 5/2 Monel/Half Stellite 11 HF NiCu NiCu NiCu 5/3 Monel/Full Stellite - HF HF NiCu NiCu 6 Alloy 20 13 A20 A20 A20 A20 X Special Special Special Special Special Special Trim Number Common Name API 600 Seat Ring Trim No. Facing (1) 1 13 Chrome 1 2 Half Stellite 3 Service Limitations Corrosive services to 750º F. Corrosive services to 300º F. Customer to specify. (1) Facing is defined as the seating surface of a seat ring and wedge/disc. (2) Other trim parts are defined as small internal parts that are normally in contact with the service fluid. This includes the stem, etc. in gate and globe valves and the swing check disc nut. Features and Benefits TC9308-4 • Material Test Reports • Ship from Multiple North American Locations • International Organization for Standardization (ISO) • Extensive Engineering Capabilities • Traceability • Excellent Customer Service • Fugitive Emissions Tested • Warranty • API-598 Tested • Field Services for Start-up • Major End-user Approved • In-house Automation Capabilities 18 I. FORGED STEEL BOLTED AND WELDED BONNET GATE VALVES SIZES: 1/4” TO 3” (6MM TO 80MM) • PRESSURE CLASS: 150 TO 4500 Cameron’s Typical NEWCO Forged Steel Bolted and Welded Bonnet Gate Valve Expanded View 1 2 11 12 3 13 14 4 5 6 11 7 15 8 16 9 10 TC9308-4 19 1. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly. 2. Handwheel: The handwheel cycles the valve. 3. Stem Nut: The stem nut provides a precision guide for proper stem alignment. 4. & 11. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for packing compression. 5. Stuffing Box: The stuffing box contains the packing. 6. Bonnet Bolts: The bonnet bolts secure the bonnet to the body. 7. Yoke and Bonnet: The bonnet assemblies are built to the same standards as the bodies. Larger size gate valves utilize a multi-piece bonnet design. 8. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and body. 9. Body: Cameron’s NEWCO forged steel bodies provide low resistance flow and optimum strength and performance. 10. Seat Rings: To ensure a stable shutoff, seat rings are aligned and swaged into the valve, then precision ground for optimal seating. 12. Gland Flange: The gland flange applies pressure to the gland for accurate packing adjustments. 13. Gland: The gland compresses the packing to create a stem seal above the back seat between the bonnet and stem. 14. Packing: The packing creates a seal above the back seat between the bonnet and stem. 15. Stem: The stem is precision machined and inserts into the horizontal channel in the disc. 16. Wedge: The solid wedge is machined to the tightest tolerances to ensure trouble free shutoff and cycling. TC9308-4 20 FORGED STEEL BOLTED AND WELDED BONNET GATES THREADED, SOCKET WELD AND BUTTWELD ENDS CONVENTIONAL PORT CLASS 800 TO 2500 SIZES: 1/4” TO 3” (6MM TO 80MM) Design and Manufacturing Standards Valve Design: API 602 Pipe Threads, General Purpose, Inch: ASME B1.20.1 Socket Welding and Threaded: ASME B16.11 Tested in Accordance With: API 598 Recommended Spare Parts* BOLTED BONNET C WELDED BONNET D B A TC9308-4 21 Class 800 to 2500 Bolted and Welded Bonnet Gates Size In. ----mm 1/4 6 3/8 9 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 3 75 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A 41 Class 800 WB C B 45 3.1 80 3.1 80 41 45 41 45 D 41 Wt. 45 - 0.31 5.7 3.1 8 145 80 0.39 5.7 3.1 10 145 80 0.39 0.39 5.7 4.9 3.2 3.3 10 10 145 124.5 80 83.8 0.55 0.55 6.1 5.2 3.2 3.3 14 14 155 132.1 80 83.8 0.71 0.71 7.3 6.7 3.9 4.7 18 18 185 170.2 100 119.4 0.95 0.95 8.6 7.6 4.7 5.9 24 24 218 193 120 149.9 1.22 1.22 10.0 8.3 5.5 5.9 30 30 255 210.8 140 149.9 1.44 1.44 10.9 9.3 5.5 6.7 36.5 36.5 277 236.2 140 170.2 - A Class 1500 WB C 3.2 80 3.5 90 4.3 110 5.0 127 5.0 127 5.1 130 3.1 78.7 3.6 91.4 4.4 111.8 4.7 119.4 4.7 119.4 5.5 139.7 B D 41 45 A 41 3.5 1.6 3.5 1.6 B 45 3.1 80 3.1 80 3.2 3.1 1.6 1.4 4.4 3.7 2 1.7 7.1 6.6 3.2 3 10.7 11 4.8 5 14.3 12.3 6.5 5.6 18.7 20.3 8.5 9.2 - 3.2 80 3.5 90 4.3 110 5.0 127 5.0 127 5.1 130 3.1 78.7 3.6 91.4 4.4 111.8 4.7 119.4 4.7 119.4 5.5 139.7 7.3 184.2 Wt. Class 800 BB C 41 45 41 45 D 41 Wt. 45 41 45 0.31 5.7 3.1 8 145 80 0.39 5.7 3.1 10 145 80 0.39 0.39 5.7 4.9 3.2 3.3 10 10 145 124.5 80 83.8 0.55 0.55 6.1 5.2 3.2 3.3 14 14 155 132.1 80 83.8 0.71 0.71 7.3 6.7 3.9 4.7 18 18 185 170.2 100 119.4 0.95 0.95 8.6 7.6 4.7 5.9 24 24 218 193 120 149.9 1.22 1.22 10.0 8.3 5.5 5.9 30 30 255 210.8 140 149.9 1.44 1.44 10.9 9.3 5.5 6.7 36.5 36.5 277 236.2 140 170.2 2.13 15.5 11.3 53.98 393.7 285.8 3.9 3.1 1.8 1.4 4.6 3.7 2.1 1.7 7.9 6.6 3.6 3 11.2 11 5.3 5 15.4 12.3 7.5 5.6 20.0 20.3 9.8 9.2 56 25.5 Class 1500 BB C Wt. A B D 3.9 1.8 3.9 1.8 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 3.5 90 4.3 110 4.7 120 5.1 130 5.1 130 5.9 150 4.4 111.8 4.4 111.8 4.5 114.3 4.7 119.4 5.5 139.7 6.4 162.6 0.39 10 0.55 14 0.75 18 0.95 24 1.16 29 1.44 36.5 0.55 13.97 0.55 13.97 0.71 18.03 0.95 24.13 1.14 28.95 1.44 36.57 6.07 152 7.1 180 8.6 218 9.8 250 10.8 275 12.6 320 7.8 198.1 7.8 198.1 8.6 218.4 9.3 236.2 10.8 274.3 12.6 320.0 3.2 80 3.9 100 4.7 120 5.5 140 5.5 140 6.7 170 4.9 124.5 4.9 124.5 6.2 157.5 6.2 157.5 7 177.8 7.9 200.7 5.0 2.2 8.4 3.6 12.6 5.2 14.6 7.5 22.0 10 33.0 14.5 9 4.1 9.5 4.3 13.5 6.1 19.2 8.7 26.9 12.2 39 17.7 3.5 90 4.3 110 4.7 120 5.1 130 5.1 130 5.9 150 4.4 111.8 4.4 111.8 4.5 114.3 4.7 119.4 5.5 139.7 6.4 162.6 0.39 10 0.55 14 0.75 18 0.95 24 1.16 29 1.44 37 0.55 139.7 0.55 139.7 0.71 18.03 0.95 24.13 1.14 28.95 1.44 36.57 6.07 152 7.1 180 8.6 218 9.9 252 10.8 275 12.6 320 7.8 198.1 7.8 198.1 8.6 218.4 9.3 236.2 10.8 274.3 12.6 320.0 3.2 80 3.9 100 4.7 120 5.5 140 5.5 170 6.7 170 4.9 124.5 4.9 124.5 6.2 157.5 6.2 157.5 7 177.8 7.9 200.7 5.5 2.5 8.4 3.8 11.9 5.4 17.6 8 22.4 10 33.0 15 9 4.1 9.5 4.3 13.5 6.1 19.2 8.7 26.9 12.2 39 17.7 TC9308-4 22 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A Class 2500 WB C B D Wt. A B Class 2500 BB C D Wt. 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 4.3 110 4.7 120 5.1 130 5.1 130 8.3 210 9.4 240 5.9 149.9 5.9 149.9 6.7 170.2 8.7 220.9 8.7 220.9 9.8 248.9 0.39 10 0.55 14 0.75 18 0.95 24 1.16 29 1.44 36.5 0.39 9.9 0.55 13.97 0.71 18.03 0.95 24.13 1.14 28.95 1.44 36.57 6.9 175 8.3 210 9.4 240 11.0 280 12.2 310 14 355 9.5 241.3 9.5 241.3 10.8 274.3 13.1 332.7 13.1 332.7 16.8 426.7 3.9 100 4.7 120 5.5 140 6.7 170 6.7 170 10.2 260 6.3 160 6.3 160 7.1 180.3 7.8 198.1 7.8 198.1 11.8 299.7 7.7 3.5 12.1 5.5 16.5 7.5 22 10 35.2 16 55 25 27.1 12.3 26.6 12.1 26 11.8 46 20.9 60.5 27.5 117.3 53.3 4.3 110 4.7 120 5.1 130 8.3 210 8.3 210 9.4 240 5.9 149.9 5.9 149.9 6.7 170.2 8.7 220.9 8.7 220.9 9.8 248.9 0.39 9.9 0.55 13.97 0.75 19.05 0.95 24.13 1.16 29.46 1.44 36.57 0.39 9.9 0.55 13.97 0.71 18.03 0.95 24.13 1.14 28.95 1.44 36.57 8.3 210 10.0 255 10.4 265 14.4 365 14.8 375 15.4 390 9.5 241.3 9.5 241.3 10.8 274.3 13.1 332.7 13.1 332.7 16.8 426.7 3.9 100 4.7 120 5.5 140 6.7 170 6.7 170 10.2 260 6.3 160 6.3 160 7.1 180.3 7.8 198.1 7.8 198.1 11.8 299.7 12.1 5.5 18.7 8.5 22.4 10.2 57.2 26 57.2 26 81.4 37 27.1 12.3 26.6 12.1 26 11.8 46 20.9 60.5 27.5 117.3 53.3 Typical Bill Materials (See page 61 for available materials) Component Material ASTM Spec Body Carbon Steel A105N Bonnet Carbon Steel A105N * Packing Graphite W/Braided Carbon Fiber End Rings * Gasket Stainless Steel 316 Graphite Stem Stainless Steel A479-410 Wedge Stainless Steel 13 Chrome Seat Rings Stainless Steel A479-410 Bonnet Bolt Alloy Steel A193 B7 Handwheel Nut Carbon Steel Commercial Nameplate Aluminum Commercial Handwheel Carbon Steel A105N Yoke Sleeve Stainless Steel AISI 416 Gland Nuts Carbon Steel A194 2H Gland Flange Carbon Steel A105N Gland Studs Stainless Steel AISI 410 Packing Gland Stainless Steel A479-316 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Dimensions are subject to change without notice. TC9308-4 23 FORGED STEEL EXTENDED BODY GATES BOLTED AND WELDED BONNET CONVENTIONAL PORT CLASS 800 TO 1500 SIZES: 1/2” TO 2” Design and Manufacturing Standards Valve Design: API 602 Pipe Threads, General Purpose, Inch: ASME B1.20.1 Socket Welding : ASME B16.11 Tested in Accordance With: API 598 Recommended Spare Parts* D Available Ends Socket Weld B Threaded WELDED BONNET BOLTED BONNET C A B Integrally Reinforced Lip End A Integrally Reinforced Contoured End B B A A TC9308-4 24 Class 800 and 1500 Extended Body Bolted and Welded Bonnet Gate Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 Class 800 IR Contoured End A B C D Wt. Class 800 IR - Lip End A B C D Wt. A Class 800 Threaded B C D Wt. Class 800 Socket Weld A B C D Wt. 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 8.6 207 8.6 218 9.6 245 10.4 263 11.4 289 A 0.39 5.9 9.9 150 0.55 6.1 13.9 155 0.71 7.3 18 185 1.14 10.2 28.9 259 1.44 10.8 36.6 274 3.2 81 3.2 81 3.9 99 5.5 140 5.5 140 6 3 7 3 10 5 19 9 29 13 Class 1500 Re-Out-Forced B C D Wt. 8.6 207 8.6 218 9.6 245 10.4 263 11.4 289 A 0.39 5.9 9.9 150 0.55 6.1 13.9 155 0.71 7.3 18 185 1.14 10.2 28.9 259 1.44 10.8 36.6 274 3.2 81 3.2 81 3.9 99 5.5 140 5.5 140 6 3 7 3 10 5 19 9 29 13 Class 1500 Re-In Forced B C D Wt. 5.6 141.5 5.8 146.5 6.5 166 7.5 191 8.5 216 A 0.39 6.4 10 162 0.55 7.3 14 185 0.7 7.6 18 192 1.14 10 29 255 1.44 10.7 36.5 273 3.1 80 3.9 100 3.9 100 5.5 140 6.7 170 5.7 5.6 0.39 6.4 2.6 141.5 10 162 6.4 5.8 0.55 7.3 2.9 146.5 14 185 9.5 6.5 0.7 7.6 4.3 166 18 192 19.4 7.5 1.14 10 8.8 191 29 255 28.6 8.5 1.44 10.7 13 216 36.5 273 Class 1500 Threaded B C D Wt. A 3.1 80 3.9 100 3.9 100 5.5 140 6.7 170 5.7 2.6 6.4 2.9 9.5 4.3 19.4 8.8 28.6 13 Class 1500 Socket Weld B C D Wt. 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 8.6 218 9.6 245 10.4 264 10.5 267 12.8 325 TC9308-4 0.39 5.4 9.9 138 0.55 6.3 13.9 161 0.75 8.6 19 218 1.16 9.4 29.5 238 1.44 10.9 36.6 276 3.2 80 3.9 100 4.7 120 5.5 140 6.7 170 6 3 10 5 15 7 25 11 35 16 8.6 218 9.6 245 10.4 264 10.5 267 12.8 325 0.39 5.4 9.9 138 0.55 6.3 13.9 161 0.75 8.6 19 218 1.16 9.4 29.5 238 1.44 10.9 36.6 276 3.2 80 3.9 100 4.7 120 5.5 140 6.7 170 6 3 10 5 15 7 25 11 35 16 25 5.7 146 6.5 166 7.5 191 8.5 216 9.8 250 0.39 6.5 3.2 6.4 10 165 80 2.9 0.55 7.1 3.9 9.5 14 180 100 4.3 0.7 9.4 5.5 19.4 18 240 140 8.8 1.14 10.6 6.7 29.7 29 270 170 13.5 1.44 12.6 10.2 41.1 36.5 320 260 18.7 5.7 146 6.5 166 7.5 191 8.5 216 9.8 250 0.39 6.5 3.2 6.4 10 165 80 2.9 0.55 7.1 3.9 9.5 14 180 100 4.3 0.7 9.4 5.5 19.4 18 240 140 8.8 1.14 10.6 6.7 29.7 29 270 170 13.5 1.44 12.6 10.2 41.1 36.5 320 260 18.7 Typical Bill of Materials (See page 61 for available materials.) Component Material ASTM Spec Body Carbon Steel A105N Bonnet Carbon Steel A105N * Packing Graphite W/Braided Carbon Fiber End Rings * Gasket Stainless Steel 316 Graphite Stem Stainless Steel A479-410 Wedge Stainless Steel 13 Chrome Seat Rings Stainless Steel A479-410 Bonnet Bolt Alloy Steel A193 B7 Handwheel Nut Carbon Steel Commercial Nameplate Aluminum Commercial Handwheel Carbon Steel A105N Yoke Sleeve Stainless Steel AISI 416 Gland Nuts Carbon Steel A194 2H Gland Flange Carbon Steel A105N Gland Studs Stainless Steel AISI 410 Packing Gland Stainless Steel A479-316 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Dimensions are subject to change without notice. TC9308-4 26 FORGED STEEL FLANGED END GATES BOLTED AND WELDED BONNET CONVENTIONAL PORT CLASS 150 TO 1500 SIZES: 1/2” TO 2” (15MM TO 50MM) (1/4” AND 3/8” AVAILABLE UPON REQUEST) Design and Manufacturing Standards Valve Design: API 602 Flange Dimensions: ASME B16.5 Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts* BOLTED BONNET C WELDED BONNET D B A TC9308-4 27 Class 150 to 1500 Bolted and Welded Bonnet Flanged Gates Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 TC9308-4 A 41 B 45 4.3 108 4.6 118 5.0 127 5.5 140 6.5 165 7.0 178 41 45 41 45 0.39 10 0.55 14 0.71 18 0.94 24 1.22 30 1.44 37 0.39 10 0.55 14 0.71 18 0.95 24 1.14 29 1.44 37 6.8 173 7.1 180 8.1 205 9.3 235 10.2 260 11.7 296 4.9 125 5.2 132 6.7 170 7.6 193 8.3 211 9.3 236 A 41 D 41 41 45 41 45 0.39 10 0.55 14 0.71 18 0.94 24 1.22 30 1.44 37 0.39 10 0.55 14 0.71 18 0.95 24 1.14 29 1.44 37 6.9 174 7.1 180 8.1 205 10.2 260 10.4 265 11.7 296 4.9 125 5.2 132 6.7 170 7.6 193 8.3 211 9.3 236 28 Wt. 45 3.2 80 3.2 80 4.0 100 4.8 120 5.5 140 5.5 170 Class 300 BB and WB C B 45 5.5 140 6.0 153 6.5 165 7.0 178 7.5 191 8.5 216 Class 150 BB and WB C 41 45 6.8 3.1 8.6 4 12.1 5.7 18.1 8.2 23.4 10.5 32.0 15.4 6.6 3 7.7 3.5 12.1 5.5 15 6.8 22.9 10.4 31.7 14.4 D 41 Wt. 45 3.2 80 3.2 80 3.9 100 4.7 140 5.5 140 6.7 170 41 45 7.3 4 10.8 5.4 14.7 6.5 21.1 12.5 29.5 13 35.9 17.5 7.9 3.6 10.8 4.9 15.4 7 20.7 9.4 29.3 13.3 39.6 18 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 TC9308-4 A 41 45 6.5 165 7.5 191 8.5 216 9.0 229 9.5 241 11.5 292 41 45 41 45 0.39 10 0.55 14 0.71 18 1.14 29 1.22 30 1.44 37 0.39 10 0.55 14 0.71 18 0.95 24 1.14 29 1.44 37 5.7 145 6.1 155 7.3 185 9.8 248 9.8 248 10.7 273 4.9 125 5.2 132 6.7 170 7.6 193 8.3 211 9.3 236 A 41 D 41 41 45 41 45 0.55 14 0.71 18 0.94 24 1.44 36.5 1.57 40 0.55 14 0.55 14 0.71 18 0.95 24 1.14 29 1.44 37 8.3 210 10.0 255 10.8 275 15 380 15.3 388 7.8 198 7.8 198 8.6 218 9.3 236 10.8 274 12.6 320 29 Wt. 45 3.2 80 3.2 80 4.0 100 5.5 140 5.5 140 5.6 170 Class 1500 BB and WB C B 45 8.5 216 9 229 10 254 12 305 14.5 368 Class 600 BB and WB C B 41 45 7.7 4.2 11.7 5.6 15.7 7.2 30.9 14.5 30.9 14.5 40.8 18 9.2 4.2 12.8 5.8 19.4 8.8 26.6 12.1 34.3 15.6 34.3 19.5 D 41 Wt. 45 3.9 100 4.7 120 5.5 140 6.8 172 10.2 260 41 45 22 10 33 15 37.4 17 77 35 121 55 9 4 9.5 4.3 13.5 6 19.2 8.7 26.9 12 39 17.7 Typical Bill of Materials (See page 61 for available materials) Component Material ASTM Spec Body Carbon Steel A105N Bonnet Carbon Steel A105N * Packing Graphite W/Braided Carbon Fiber End Rings * Gasket Stainless Steel 316 Graphite Stem Stainless Steel A479-410 Wedge Stainless Steel 13 Chrome Seat Rings Stainless Steel A479-410 Bonnet Bolt Alloy Steel A193 B7 Handwheel Nut Carbon Steel Commercial Nameplate Aluminum Commercial Handwheel Carbon Steel A105N Yoke Sleeve Stainless Steel AISI 416 Gland Nuts Carbon Steel A194 2H Gland Flange Carbon Steel A105N Gland Studs Stainless Steel AISI 410 Packing Gland Stainless Steel A479-316 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-4 30 FORGED STEEL HIGH PRESSURE WELDED BONNET GATE CONVENTIONAL PORT CLASS 4500 SIZES: 1/2” TO 2” (15MM TO 50MM) Design and Manufacturing Standards Valve Design: ASME B16.34 Pipe Threads, General Purpose, Inch: ASME B1.20.1 Socket Welding: ASME B16.11 Tested in Accordance With: API 598 Recommended Spare Parts* D C B A TC9308-4 31 Size A 4.7 120 5.1 130 5.1 130 8.3 210 8.3 210 9.4 240 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 B 0.47 12 0.47 12 0.47 12 0.63 16 0.63 16 0.83 21 Class 4500 Welded Bonnet Gate C 10.4 265 10.4 265 10.4 265 12.4 315 12.4 315 15.4 390 D 5.5 140 5.5 140 6.7 170 6.7 170 10.2 260 10.2 260 Wt. 17.6 8 19.8 9 19.8 9 31.9 14.5 33 15 41.8 19 Typical Bill of Materials (See page 61 for available materials) Component Material ASTM Spec Body Carbon Steel A105N Bonnet Carbon Steel A105N * Packing Graphite W/Braided Carbon Fiber End Rings * Gasket Stainless Steel 316 Graphite Stem Stainless Steel A479-410 Wedge Stainless Steel 13 Chrome Seat Rings Stainless Steel A479-410 Bonnet Bolt Alloy Steel A193 B7 Handwheel Nut Carbon Steel Commercial Nameplate Aluminum Commercial Handwheel Carbon Steel A105N Yoke Sleeve Stainless Steel AISI 416 Gland Nuts Carbon Steel A194 2H Gland Flange Carbon Steel A105N Gland Studs Stainless Steel AISI 410 Packing Gland Stainless Steel A479-316 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-4 32 II. FORGED STEEL BOLTED AND WELDED BONNET GLOBE VALVES SIZES: 1/2” TO 2” (15MM TO 50MM) • PRESSURE CLASS: 150 TO 4500 Cameron’s Typical NEWCO Forged Steel Bolted and Welded Bonnet Globe Valve Expanded View 1 2 3 4 13 5 6 7 14 15 8 8 4 9 10 11 12 16 17 18 19 20 TC9308-4 33 1. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly. 2. Handwheel Washer: The washer helps to prevent loosening. 3. Handwheel: The handwheel cycles the valve. 4. & 14. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for packing compression. 5. Gland Flange: The gland flange applies pressure to the gland for accurate packing compression. 6. Gland: The gland compresses the packing to create a stem seal above the back seat between the bonnet and stem. 7. Packing: The packing creates a seal above the back seat between the bonnet and stem. 8. Bonnet Bolts: The bonnet bolts secure the bonnet to the body. 9. Bonnet: Cameron’s NEWCO bonnet assemblies are built to the same standards as the bodies. 10. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and body. 11. Body: Cameron’s NEWCO forged steel bodies provide low resistance flow and optimum strength and performance 12. Seat Ring: To ensure a stable shutoff, the seat ring is aligned into the valve, then precision ground for optimal seating. 13. Stem Nut: The stem nut provides a precision guide for proper stem alignment. 15. Stuffing Box: The stuffing box contains the packing. 16. Stem: The stem inserts vertically into the disc. 17. Lock Groove: The lock groove receives the split lock ring which allows the disc nut to lift the disc during cycling. 18. Disc Nut: The disc nut, in conjunction with the split lock ring, secures the disc to the stem. 19. Split Ring: The split ring allows the disc nut to lift the disc during cycling. 20. Disc: Cameron’s NEWCO plug type disc is machined to the tightest tolerances to ensure trouble free shutoff and cycling. TC9308-4 34 FORGED STEEL BOLTED AND WELDED BONNET GLOBES THREADED, SOCKET WELD AND BUTTWELD ENDS CONVENTIONAL PORT CLASS 800 TO 2500 SIZES: 1/2” TO 2” (15MM TO 50MM) (1/4” AND 3/8” AVAILABLE UPON REQUEST) Design and Manufacturing Standards Valve Design: API 602 Pipe Threads, General Purpose, Inch: ASME B1.20.1 Socket Welding: ASME B16.11 Tested in Accordance With: API 598 Recommended Spare Parts* BOLTED BONNET C WELDED BONNET D B A TC9308-4 35 Class 800 to 1500 Bolted and Welded Bonnet Globes Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A Class 800 WB C B 41 45 3.2 80 3.5 90 4.3 110 5 127 6.1 155 6.7 170 3.1 78.7 3.6 91.4 4.4 111.8 4.7 119.4 6 152.4 6.8 172.7 41 45 0.35 9 0.49 12.5 0.68 17.5 0.88 22.5 1.14 29 1.37 35 A B D Wt. A B 41 45 41 45 41 45 41 45 6.3 160 6.7 170 7.9 200 9.3 235 9.3 270 11.4 290 5.2 132.1 5.4 137.2 7 177.8 8.3 210.8 8.4 213.4 10.3 261.6 3.2 80 3.2 80 3.9 100 4.7 120 5.5 140 6.7 170 3.3 83.8 3.3 83.8 4.7 119.4 5.9 149.9 5.9 149.9 6.7 170.2 4 1.8 4.4 2 7.3 3.3 11.9 5.4 17.4 7.9 23.8 10.8 2.9 1.3 3.7 1.7 6.4 2.9 15.9 7.2 14.9 6.8 23.4 10.6 3.2 80 3.5 90 4.3 110 5 127 6.1 155 6.7 170 3.1 78.7 3.6 91.4 4.4 111.8 4.7 119.4 6 152.4 6.8 172.7 Class 1500 WB C D Wt. Class 800 BB C 41 45 0.35 9 0.49 12.5 0.68 17.5 0.88 22.5 1.14 29 1.37 35 A B D Wt. 41 45 41 45 41 45 6.3 160 6.7 170 7.9 200 9.3 235 9.3 270 11.4 290 5.2 132.1 5.4 137.2 7 177.8 8.3 210.8 8.4 213.4 10.3 261.6 3.2 80 3.2 80 3.9 100 4.7 120 5.5 140 6.7 170 3.3 83.8 3.3 83.8 4.7 119.4 5.9 149.9 5.9 149.9 6.7 170.2 4 1.8 4.4 2 7.3 3.3 11.9 5.4 17.4 7.9 23.8 10.8 2.9 1.3 3.7 1.7 6.4 2.9 15.9 7.2 14.9 6.8 23.4 10.6 Class 1500 BB C D Wt. 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 3.5 90 4.3 110 4.7 120 5.1 130 6.7 170 8.3 210 4.4 111.8 4.4 111.8 5.1 129.5 5.9 149.9 6.8 172.7 8.7 220.9 0.35 9 0.43 11 0.57 14.5 0.75 19 1.06 27 1.22 31 0.39 9.9 0.51 12.95 0.66 16.76 0.9 22.86 1.18 29.97 1.49 37.85 6.5 165 7.7 195 9.3 235 10.4 265 11 280 13.2 335 8.1 205.7 8.1 205.7 9.4 238.8 10.2 259.1 11.4 289.6 13.3 337.8 3.2 80 4.7 120 5.5 140 5.5 140 6.7 170 6.7 170 4.9 124.5 4.9 124.5 6.2 157.5 6.2 157.5 6.2 157.5 7.1 180.3 4.2 1.9 7 3.2 12.1 5.5 17.6 8 24.2 11 39.6 18 4.4 2 8.4 3.8 9.3 4.2 17.6 8 29.1 13.2 37 16.8 3.5 90 4.3 110 4.7 120 5.1 130 6.7 170 8.3 210 4.4 111.8 4.4 111.8 5.1 129.5 5.9 149.9 6.8 172.7 8.7 220.9 0.35 9 0.43 11 0.57 14.5 0.75 19 1.06 27 1.22 31 0.39 9.9 0.51 12.95 0.66 16.76 0.9 22.86 1.18 29.97 1.49 37.85 6.5 165 7.7 195 9.1 230 10.2 260 11.2 285 13 330 8.1 205.7 8.1 205.7 9.4 238.8 10.2 259.1 11.4 289.6 13.3 337.8 3.2 80 4.7 120 5.5 140 5.5 140 6.7 170 6.7 170 4.9 124.5 4.9 124.5 6.2 157.5 6.2 157.5 6.2 157.5 7.1 180.3 4.4 2 7.3 3.3 12.1 5.5 19.8 9 26.4 12 39.6 18 4.4 2 8.4 3.8 9.3 4.2 17.6 8 29.1 13.2 37 16.8 TC9308-4 36 Size In. A ----mm 41 45 1/2 4.3 15 110 3/4 4.7 20 120 1 5.1 25 130 1-1/4 8.3 32 210 1-1/2 8.3 40 210 2 9.5 50 240 Class 2500 WB C B 41 45 0.43 11 0.55 14 0.75 19 0.94 24 1.1 28 1.42 36 41 45 7.7 195 8.9 225 10 255 12.8 325 13 330 14.6 370 D 41 Wt. 45 4.7 120 5.5 140 5.5 140 6.7 170 6.7 170 10.2 260 41 45 A 41 8.6 3.9 14.1 6.4 19.9 9 44 20 48.4 22 61.6 28 45 4.3 110 4.7 120 5.1 130 8.3 210 8.3 210 9.5 240 Class 2500 BB C B 41 45 0.43 11 0.55 14 0.75 19 0.94 24 1.1 28 1.42 36 41 45 10.6 270 10.8 275 11.4 290 15.4 390 16.3 415 16.7 425 D 41 Wt. 45 4.7 120 5.5 140 5.5 140 6.7 170 10.2 260 10.2 260 Typical Bill Materials (See page 61 for available materials) Component Material ASTM Spec Body Carbon Steel A105N Bonnet Carbon Steel A105N * Packing Graphite W/Braided Carbon Fiber End Rings * Gasket Stainless Steel 316 Graphite Stem Stainless Steel A479-410 Disc Stainless Steel 13 Chrome Seat Rings Stainless Steel A479-410 Bonnet Bolt Alloy Steel A193 B7 Washer Carbon Steel Commercial Handwheel Nut Carbon Steel Commercial Nameplate Aluminum Commercial Handwheel Carbon Steel Commercial Yoke Sleeve Stainless Steel AISI 416 Gland Nuts Carbon Steel A194 2H Gland Flange Carbon Steel A105N Gland Studs Stainless Steel AISI 410 Packing Gland Stainless Steel AISI 416 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-4 37 41 45 11 5 17.6 8 23.5 10.7 52.8 24 70.4 32 81.4 37 FORGED STEEL FLANGED END GLOBES BOLTED AND WELDED BONNET CONVENTIONAL PORT CLASS 150 TO 1500 SIZES: 1/2” TO 2” (15MM TO 50MM) (1/4” AND 3/8” AVAILABLE UPON REQUEST) Design and Manufacturing Standards Valve Design: API 602 Flange Dimensions: ASME B16.5 Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts* BOLTED BONNET C WELDED BONNET D B A TC9308-4 38 Class 150 to 1500 Bolted and Welded Bonnet Flanged Globes Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 TC9308-4 A 41 45 4.25 108 4.63 118 5.00 127 6.50 165 8.00 203 41 45 41 45 0.35 9 0.47 12.5 0.67 17.5 1.10 29 1.34 35 0.39 9.9 0.39 9.9 0.69 17.5 1.18 30 1.46 37.1 7.3 185 7.6 192 8.7 220 10.4 265 12.2 310 6.8 173 7.0 178 8.3 211 9.2 234 10.4 264 A 41 6.00 152.5 7.00 178 8.00 203 9.00 229 10.5 267 41 45 41 45 0.35 9 0.47 12.5 0.67 17.5 1.10 29 1.34 35 0.39 9.9 0.39 9.9 0.69 17.5 1.18 30 1.46 37.1 6.3 160 6.6 168 7.9 200 10.6 268 11.4 290 6.26 159 6.26 159 7.6 193 9.2 234 10.4 264 A 6.50 165 7.50 190.5 8.50 216 9.51 241.5 11.5 292 41 41 45 41 45 0.35 9 0.47 12.5 0.67 17.5 1.10 29 1.34 35 0.39 9.9 0.39 9.9 0.69 17.5 1.18 30 1.46 37.1 6.3 160 6.6 168 7.9 200 10.6 268 11.4 290 6.26 159 6.26 159 7.6 193 8.7 221 10.4 264 39 Wt. 45 3.1 80 3.1 80 4.0 100 5.5 140 6.7 170 41 45 7 3.1 8 4 17 5.7 25 10.6 35 15.4 9.9 4.5 15.2 6.9 21.6 9.8 42.9 19.5 61.6 28 D 41 Wt. 45 3.1 80 3.1 80 4.0 100 5.5 140 6.7 170 Class 600 BB and WB C B 45 D Class 300 BB and WB C B 45 41 Class 150 BB and WB C B 41 45 8 3.5 11 4.8 15 7.2 30 14.5 40 18 10.6 4.8 16.9 7.7 24.2 11 46.6 21.2 71.7 32.6 D 41 Wt. 45 3.1 80 3.1 80 4.0 100 5.5 140 6.7 170 41 45 8.2 3.7 11.7 5.3 18.1 8.2 33.1 15 47.4 21.5 12.3 5.6 17.2 7.8 27.5 12.5 51.7 23.5 85.4 38.8 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A 41 45 8.5 216 9.0 229 10.0 254 11.0 279 12.0 305 14.5 368 Class 1500 BB and WB C B D Wt. 41 45 41 45 41 45 41 45 .43 11 .57 14.5 .75 19 1.22 31 1.48 37.5 0.5 13 0.7 18 0.9 24 1.1 29 1.4 36.5 1.8 46.5 8.86 225 10.63 270 11.22 285 15.75 400 16.54 420 8.1 207 9.4 240 10.2 258 11.4 290 13.3 337 14.0 354 4.72 120 5.51 140 5.51 140 6.69 170 10.24 260 3.93 100 4.92 125 6.29 160 6.29 160 7.08 180 9.45 240 22.0 10.0 33.0 15.0 37.4 17.0 79.2 36.0 121.0 55.0 17.6 8.0 29.0 13.2 38.3 17.4 42.0 19.0 54.0 24.5 68.2 31.0 Typical Bill Materials (See page 61 for available materials) Component Material ASTM Spec Body Carbon Steel A105N Bonnet Carbon Steel A105N * Packing Graphite W/Braided Carbon Fiber End Rings * Gasket Stainless Steel 316 Graphite Stem Stainless Steel A479-410 Disc Stainless Steel 13 Chrome Seat Rings Stainless Steel A479-410 Bonnet Bolts Alloy Steel A193 B7 Washer Carbon Steel Commercial Handwheel Nut Carbon Steel Commercial Nameplate Aluminum Commercial Handwheel Carbon Steel Commercial Yoke Sleeve Stainless Steel AISI 416 Gland Nuts Carbon Steel A194 2H Gland Flange Carbon Steel A105N Gland Studs Stainless Steel AISI 410 Packing Gland Stainless Steel AISI 416 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-4 40 FORGED STEEL Y-PATTERN BOLTED AND WELDED BONNET GLOBE CONVENTIONAL PORT CLASS 800 TO 2680 SIZES: 1/2” TO 2” (15MM TO 50MM) (1/4” AND 3/8” AVAILABLE UPON REQUEST) Design and Manufacturing Standards Valve Design: ASME B16.34 Pipe Threads, General Purpose, Inch: ASME B1.20.1 Socket Welding: ASME B16.11 Tested in Accordance With: API 598 Recommended Spare Parts* BOLTED BONNET WELDED BONNET D C B A TC9308-4 41 A 3.6 92 3.6 92 4.4 111 6 152 6 152 6.8 172 Class 800 Bolted and Welded Bonnet Globe B C D 0.39 7.5 3.7 10 190 95 0.51 7.5 3.7 13 190 95 0.69 9.3 4.3 17.5 235 110 0.94 11.2 5.5 24 286 140 1.22 11.2 5.5 31 286 140 1.46 12.8 6.7 37 325 200 Wt. 4.4 2 4.4 2 9 4.1 19.8 9 19.8 9 30.4 13.8 A 3.9 100 4.3 110 4.9 125 5.9 150 6.3 160 7.5 190 B 0.51 13 0.69 17.5 0.89 22.5 1.1 28 1.38 35 1.73 44 Class 1500 and 1690 Welded Bonnet Globe C 7.3 185 9.1 230 9.4 240 12 305 13.4 340 15.7 400 D 3.9 100 5.5 140 5.5 140 6.7 170 7.9 200 10.2 260 Wt. 6.6 3 8.8 4 11 5 20.9 9.5 24.2 11 37.4 17 B 0.47 12 0.59 15 0.79 20 0.98 25 1.22 31 1.49 38 Class 2500 and 2680 Welded Bonnet Globe C 9.1 230 9.4 240 12 305 12 305 13.6 345 15.7 400 D 4.7 120 5.5 140 6.7 170 6.7 170 7.9 200 10.2 260 Wt. 8.8 4 11 5 20.9 9.5 23.1 10.5 37.4 17 50.6 23 Size 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 Size 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 Size 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 TC9308-4 A 3.9 100 4.9 125 6.3 160 6.3 160 7.5 190 8.3 210 42 Typical Bill of Materials (See page 61 for available materials) Component Material ASTM Spec Body Carbon Steel A105N Bonnet Carbon Steel A105N * Packing Graphite W/Braided Carbon Fiber End Rings * Gasket Stainless Steel 316 Graphite Stem Stainless Steel A479-410 Disc Stainless Steel 13 Chrome Seat Rings Stainless Steel A479-410 Bonnet Bolts Alloy Steel A193 B7 Washer Carbon Steel Commercial Handwheel Nut Carbon Steel Commercial Nameplate Aluminum Commercial Handwheel Carbon Steel Commercial Yoke Sleeve Stainless Steel AISI 416 Gland Nuts Carbon Steel A194 2H Gland Flange Carbon Steel A105N Gland Studs Stainless Steel AISI 410 Packing Gland Stainless Steel AISI 416 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-4 43 FORGED STEEL HIGH PRESSURE WELDED BONNET GLOBE CONVENTIONAL PORT CLASS 4500 SIZES: 1/2” TO 2” (15MM TO 50MM) Design and Manufacturing Standards Valve Design: ASME B16.34 Pipe Threads, General Purpose, Inch: ASME B1.20.1 Socket Welding: ASME B16.11 Tested in Accordance With: API 598 Recommended Spare Parts* D C B A Size 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 TC9308-4 A 4.7 120 6.1 155 6.1 155 8.3 210 8.3 210 9.4 240 B 0.31 8 0.47 12 0.59 15 0.79 20 0.98 25 1.1 28 Class 4500 Welded Bonnet Globe C 8.9 228 10.8 275 11 280 16.1 410 16.1 410 16.5 420 44 D 4.7 120 5.5 140 5.5 140 10.2 260 10.2 260 10.2 260 Wt. 17.6 8 4 11 41.8 19 50.6 23 50.6 23 50.6 23 Typical Bill of Materials (See page 61 for available materials) TC9308-4 Component Material ASTM Spec Body Carbon Steel A105N Bonnet Carbon Steel A105N * Packing Graphite W/Braided Carbon Fiber End Rings * Gasket Stainless Steel 316 Graphite Stem Stainless Steel A479-410 Disc Stainless Steel 13 Chrome Seat Rings Stainless Steel A479-410 Bonnet Bolts Alloy Steel A193 B7 Washer Carbon Steel Commercial Handwheel Nut Carbon Steel Commercial Nameplate Aluminum Commercial Handwheel Carbon Steel Commercial Yoke Sleeve Stainless Steel AISI 416 Gland Nuts Carbon Steel A194 2H Gland Flange Carbon Steel A105N Gland Studs Stainless Steel AISI 410 Packing Gland Stainless Steel AISI 416 45 D C B A Size 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A 4.9 125 6.3 160 7.5 190 7.5 190 8.3 210 11 280 Class 4500 Welded Bonnet Y-Pattern Globe B C D 0.31 9.4 5.5 8 240 140 0.43 11.2 6.7 11 285 170 0.59 12.6 7.9 15 320 200 0.71 12.6 7.9 18 320 200 0.79 12.6 10.2 20 360 260 0.98 17.7 14.6 25 450 370 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-4 46 Wt. 12.1 5.5 22 10 37.4 17 37.4 17 41.8 19 52.8 24 III. FORGED STEEL BOLTED AND WELDED BONNET CHECK VALVES SIZES: 1/2” TO 2” (15MM TO 50MM) • PRESSURE CLASS: 150 TO 1500 Cameron’s Typical NEWCO Forged Steel Bolted Check Valve Expanded View 2 3 4 5 6 7 1 TC9308-4 47 1. Body: Cameron’s NEWCO forged steel bodies provide low resistance flow and optimum strength and performance. 2. Cover Studs: The cover studs secure the bonnet to the body. 3. Cover: The cover allows access to internal components. 4. Spring: The spring is precision made and loaded for precise pressures. 5. Piston: Cameron’s NEWCO piston is machined to the tightest tolerances to ensure trouble free shutoff and cycling. 6. Cover Gasket: The cover gasket creates a leak-proof seal between the bonnet and the body. 7. Seat: The seat ensures a stable shutoff. The seat is precision ground for optimal seating. TC9308-4 48 FORGED STEEL LIFT AND SWING CHECKS BOLTED AND WELDED COVER CONVENTIONAL PORT CLASS 800 TO 1500 SIZES: 1/2” TO 2” (15MM TO 50MM) (1/4” AND 3/8” AVAILABLE UPON REQUEST) Design and Manufacturing Standards Valve Design: API 602 Pipe Threads, General Purpose, Inch: ASME B1.20.1 Socket Welding: ASME B16.11 Tested in Accordance With: API 598 BOLTED BONNET C WELDED BONNET Recommended Spare Parts* B D BOLTED BONNET C WELDED BONNET A B D A TC9308-4 49 Class 800 to 1500 Bolted and Welded Bonnet – Lift and Swing Check Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A B Class 800 BB Lift C D 41 45 41 45 41 45 3.2 80 3.5 90 4.3 110 5 127 6.1 155 6.7 170 3.1 78.7 3.6 91.4 4.4 111.8 4.7 119.4 6 152.4 6.8 172.7 0.35 9 0.49 12.5 0.68 17.5 0.88 22.5 1.14 29 1.38 35 0.39 9.9 0.54 13.9 0.69 17.5 0.9 22.9 1.18 29.9 1.45 36.8 1.9 1.9 49 49 2.2 2.1 55 53.3 2.8 2.7 70 68.6 3 3.3 77 83.8 4.1 3.7 105 94 4.7 4.4 120 111.8 45 0.85 21.6 1.07 27.2 1.33 33.8 1.67 42.4 1.92 48.8 2.41 61.2 Class 800 WB Lift B C D A 41 45 41 45 41 3.2 80 3.5 90 4.3 110 5 127 6.1 155 6.7 170 3.1 78.7 3.6 91.4 4.4 111.8 4.7 119.4 6 152.4 6.8 172.7 0.35 9 0.49 12.5 0.68 17.5 0.88 22.5 1.14 29 1.38 35 0.39 9.9 0.54 13.9 0.69 17.5 0.9 22.9 1.18 29.9 1.45 36.8 1.9 1.9 49 49 2.2 2.1 56 53.3 2.7 2.7 69 68.6 3.2 3.3 80 83.8 3.7 3.7 95 94 4.1 4.4 105 111.8 TC9308-4 41 Wt. 45 41 41 A 0.85 21.6 1.07 27.2 1.33 33.8 1.67 42.4 1.92 48.8 2.41 61.2 Class 800 BB Swing C D 45 41 45 41 45 41 45 2.4 2.1 1.1 1 4 2.6 1.8 1.2 5.7 4.3 2.6 2 7.9 11.5 3.6 5.2 12.1 9.9 5.5 4.5 18.5 17 8.4 7.7 3.2 80 3.5 90 4.3 110 5 127 5 127 5.1 130 3.1 78.7 3.6 91.4 4.4 111.8 4.7 119.4 4.7 119.4 5.5 139.7 0.35 9 0.49 12.5 0.68 17.5 0.88 22.5 1.14 29 1.44 36.6 0.39 9.9 0.55 13.9 0.71 18 0.95 24.1 1.14 29 1.44 36.6 1.9 49 2.2 55 2.8 70 3 77 4.1 105 4.7 119 1.6 40.6 1.8 45.7 2.3 58.4 3.3 83.8 3.1 78.7 3.7 94 Wt. 45 B 41 45 0.85 21.6 1.07 27.2 1.33 33.8 1.67 42.4 1.92 48.8 2.41 61.2 Class 800 WB Swing B C D A 45 41 45 41 45 41 45 2 2.1 0.9 1 2.6 2.6 1.2 1.2 4.6 4.3 2.1 2 7.5 11.5 3.4 5.2 11.7 9.9 5.3 4.5 17.2 17 7.8 7.7 3.2 80 3.5 90 4.3 110 5 127 5 127 5.1 130 3.1 78.7 3.6 91.4 4.4 111.8 4.7 119.4 4.7 119.4 5.5 139.7 0.35 9 0.49 12.5 0.68 17.5 0.88 22.5 1.14 29 1.38 35 0.39 9.9 0.55 13.9 0.71 18 0.95 24.1 1.14 29 1.44 36.6 1.9 49 2.2 56 2.7 69 3.2 80 3.7 95 4.1 105 1.6 40.6 1.8 45.7 2.3 58.4 3.3 83.8 3.1 78.7 3.7 94 50 41 Wt. 41 41 45 2.4 2.1 1.1 1 4 2.5 1.8 1.1 5.7 3.9 2.6 1.8 7.9 10.6 3.6 4.8 12.1 8.8 5.5 4 19.6 13.2 8.9 6 Wt. 45 0.85 21.6 1.07 27.2 1.33 33.8 1.67 42.4 1.92 48.8 2.41 61.2 41 45 2 2.1 0.9 1 2.6 2.5 1.2 1.1 4.6 3.9 2.1 1.8 7.5 10.6 3.4 4.8 11.7 8.8 5.3 4 17.2 13.2 7.8 6 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/4 32 1-1/2 40 2 50 A B Class 1500 BB Lift C D 41 45 41 45 3.5 90 4.3 110 4.7 120 5.1 130 6.7 170 8.3 210 4.4 111.8 4.4 111.8 5.1 129.5 6.8 172.7 8.7 220.9 0.35 9 0.43 11 0.57 14.5 0.74 19 1.06 27 1.22 31 0.39 9.9 0.51 12.95 0.66 16.76 1.18 29.97 1.49 37.85 A B 45 2.2 3.1 55 78.7 2.8 3.1 70 78.7 3 3.8 77 96.5 4.1 105 4.5 4.7 115 119.4 5.7 5.5 145 139.7 41 45 0.85 21.6 1.07 27.2 1.33 33.8 1.67 42.4 1.92 48.8 2.41 61.2 Class 1500 WB Lift C D 41 45 41 45 3.5 90 4.3 110 4.7 120 5.1 130 6.7 170 8.3 210 4.4 111.8 4.4 111.8 5.1 129.5 6.8 172.7 8.7 220.9 0.35 9 0.43 11 0.57 14.5 0.74 19 1.06 27 1.22 31 0.39 9.9 0.51 12.95 0.66 16.76 1.18 29.97 1.49 37.85 TC9308-4 41 Wt. 41 45 2.2 3.1 55 78.7 2.8 3.1 70 78.7 3.2 3.8 80 96.5 3.5 90 3.9 4.7 100 119.4 4.5 5.5 115 139.7 41 41 45 41 45 41 45 4.8 2.2 6.8 3.1 9.2 4.2 12.8 5.8 20.7 9.4 26.6 12.1 7.5 3.4 10.6 4.8 15.2 6.9 19.4 8.8 27.1 12.3 3.5 90 4.3 110 4.7 120 5.1 130 5.1 130 8.3 210 4.4 111.8 4.4 111.8 4.5 114.3 5.5 139.7 6.4 162.6 0.35 9 0.43 11 0.57 14.5 0.74 19 1.06 27 1.22 31 0.55 13.97 0.55 13.97 0.71 18.03 1.14 28.95 1.44 36.57 Wt. 45 0.85 21.6 1.07 27.2 1.33 33.8 1.67 42.4 1.92 48.8 2.41 61.2 Class 1500 BB Swing B C D A 45 2.2 3.1 55 78.7 2.8 3.1 70 78.7 3 3.8 77 96.5 4.1 105 4.5 4.7 115 119.4 5.7 5.5 145 139.7 41 45 0.85 21.6 1.07 27.2 1.33 33.8 1.67 42.4 1.92 48.8 2.41 61.2 Class 1500 WB Swing B C D A 41 45 41 45 41 45 2.9 1.3 5.5 2.5 8.4 3.8 12.1 5.5 18.3 8.3 24.2 11 7.5 3.4 10.6 4.8 15.2 6.9 19.4 8.8 27.1 12.3 3.5 90 4.3 110 4.7 120 5.1 130 5.1 130 8.3 210 4.4 111.8 4.4 111.8 4.5 114.3 5.5 139.7 6.4 162.6 0.35 9 0.43 11 0.57 14.5 0.74 19 1.06 27 1.22 31 0.55 13.97 0.55 13.97 0.71 18.03 1.14 28.95 1.44 36.57 51 41 Wt. 41 45 2.2 3.1 55 78.7 2.8 3.1 70 78.7 3.2 3.8 80 96.5 3.5 90 3.9 4.7 100 119.4 4.5 5.5 115 139.7 41 41 45 4.8 2.2 6.8 3.1 9.2 4.2 12.8 5.8 20.7 9.4 26.6 12.1 7.9 3.6 9.5 4.3 23.5 10.7 27.7 12.6 34.1 15.5 Wt. 45 0.85 21.6 1.07 27.2 1.33 33.8 1.67 42.4 1.92 48.8 2.41 61.2 41 45 2.9 1.3 5.5 2.5 8.4 3.8 12.1 5.5 18.3 8.3 24.2 11 7.9 3.6 9.5 4.3 23.5 10.7 27.7 12.6 34.1 15.5 Typical Bill Materials (See page 61 for available materials) Component Material ASTM Spec Body Carbon Steel A105N Seat Ring Stainless Steel A479-410 Piston Stainless Steel A479-410 Rivet Brass Commercial Spring Stainless Steel A479-316 Nameplate Aluminum Commercial * Gasket Stainless Steel 316 W/Graphite Spiral Wound Cap Carbon Steel A105N Cap Bolt Alloy Steel A193-B7 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-4 52 FORGED STEEL LIFT AND SWING CHECKS BOLTED AND WELDED COVER CONVENTIONAL PORT CLASS 150 TO 1500 SIZES: 1/2” TO 2” (15MM TO 50MM) (1/4” AND 3/8” AVAILABLE UPON REQUEST) Design and Manufacturing Standards Valve Design: ASME B16.34 Flange Dimensions: ASME B16.5 Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 BOLTED BONNET C WELDED BONNET Recommended Spare Parts* B D BOLTED BONNET C WELDED BONNET A B A TC9308-4 53 D Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 TC9308-4 Class 150 to 1500 Bolted and Welded Bonnet - Lift and Swing Check Class 150 B (Lift) B (Swing) C A 41 45 41 45 4.3 108 4.6 118 5 127 6.5 165 8 203 0.35 9 0.49 12.5 0.68 17.5 1.14 29 1.37 35 A (Lift) 41 41 6 152.5 7 178 8 203 9 229 10.5 267 41 45 41 0.35 9 0.49 12.5 0.68 17.5 1.14 29 1.37 35 B (Lift) 45 6.5 165 7.5 191 8.5 216 9.5 241 11.5 292 45 41 45 0.35 9 0.49 12.5 0.68 17.5 1.14 29 1.37 35 41 45 2.8 70 3.2 80 3.6 92 3.9 100 5.5 140 1.6 40.6 1.8 45.7 2.3 58.4 3.1 78.7 3.7 94 Class 300 B (Swing) B (Lift) 6 152.5 7 178 8.5 216 9.5 241 10.5 267 A 45 0.4 10 0.4 10 0.7 18 1.2 29.5 1.4 36.5 A (Swing) 45 41 41 45 0.4 10 0.6 14 0.7 18 1.2 30 1.4 36.5 Class 600 B (Swing) 41 45 0.4 10 0.6 14 0.7 18 1.2 30 1.4 36.5 54 D Wt. 41 45 41 0.5 12.7 0.75 19.1 1 25.4 1.5 38.1 2 50.8 C 6.2 2.8 8.8 4 11.7 5.3 19.8 9 33 15 D 41 45 2 50 2.2 55 2.8 70 3.9 98 4.3 110 1.6 40.6 1.8 45.7 2.3 58.4 3.1 78.7 3.7 94 41 2 50 2.2 55 2.8 70 3.9 98 4.3 110 1.6 40.6 1.8 45.7 2.3 58.4 3.1 78.7 3.7 94 41 8.2 12 14.3 45 6.2 2.8 10.3 4.7 12.5 5.7 26 11.8 37.4 17 8.1 3.7 10.6 4.8 19.4 8.8 30.1 13.7 39.2 17.8 Wt. 45 0.5 12.7 0.75 19.1 1 25.4 1.5 38.1 2 50.8 4.4 41 D 45 3.4 Wt. 45 0.5 12.7 0.75 19.1 1 25.4 1.5 38.1 2 50.8 C 41 45 41 45 6.4 2.9 10.6 4.8 21.3 9.7 26.4 12 38.1 17.3 8.8 4 12.8 5.8 20.9 9.5 34.3 15.6 53.9 24.5 Size In. ----mm 1/2 15 3/4 20 1 25 1-1/2 40 2 50 A 41 B (Lift) 45 8.5 216 9 229 10 254 12 305 14.5 368 41 45 0.43 11 0.57 14.5 0.74 19 1.22 31 1.48 37.5 Class 1500 B (Swing) C 41 45 0.6 14 0.7 18 0.9 24 1.4 36 1.6 40 41 D 45 3.5 90 4.1 105 4.7 120 6.3 160 6.7 170 Wt. 41 45 41 0.5 12.7 0.69 17.5 0.87 22.1 1.37 34.8 1.87 47.5 Typical Bill Materials (See page 61 for available materials) Component Material ASTM Spec Body Carbon Steel A105N Seat Ring Stainless Steel A479-410 Piston Stainless Steel A479-410 Rivet Brass Commercial Spring Stainless Steel A479-316 Nameplate Aluminum Commercial * Gasket Stainless Steel 316 W/Graphite Spiral Wound Cap Carbon Steel A105N Cap Bolt Alloy Steel A193-B7 Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-4 55 45 16.7 7.6 23.8 10.8 31.9 14.5 68.2 31 94.6 43 IV. FORGED STEEL CV VALUES GATES, GLOBES, CHECKS Cameron’s NEWCO Forged Steel Gate Valves Cv Values NPS 150 - 800 Full Bore 150 - 800 Reduced Bore 1500 Full Bore 1500 Reduced Bore 2500 Full Bore 1/2 12 6 13 6 5 3/4 23 10 24 11 12 1 43 26 44 27 23 1-1/4 57 44 59 45 43 1-1/2 98 65 100 66 56 2 200 103 * 99 97 * 40mm = > 155 Cameron’s NEWCO Forged Steel Globe Valves Cv Values Cameron’s NEWCO Forged Steel Y-Pattern Globe Valves Cv Values Cameron’s NEWCO Forged Steel Swing Check Valves Cv Values TC9308-4 NPS 150 - 800 Full Bore 150 - 800 Reduced Bore 1500 Full Bore 1500 Reduced Bore 1/2 3 2 3 2 3/4 6 4 6 3 1 12 6 12 6 1-1/4 15 10 -- -- 1-1/2 21 18 20 16 2 38 22 24 20 NPS 800 1500 2500 1/2 5 5 3 3/4 11 11 6 1 14 15 12 1-1/4 -- -- -- 1-1/2 37 35 27 2 68 68 36 NPS 150 - 800 Full Bore 150 - 800 Reduced Bore 1500 Full Bore 1500 Reduced Bore 1/2 5 4 -- -- 3/4 12 6 -- -- 1 17 13 -- -- 1-1/4 26 18 -- -- 1-1/2 54 28 -- -- 2 101 55 -- -- 56 Cameron’s NEWCO Forged Steel Lift Check Valves Cv Values NPS 150 - 800 Full Bore 150 - 800 Reduced Bore 1500 Full Bore 1500 Reduced Bore 1/2 3 1 3 2 3/4 5 3 6 3 1 11 6 11 5 1-1/4 -- -- -- -- 1-1/2 18 15 19 11 2 32 18 22 19 Table applies to both piston and ball check valves. Cameron’s NEWCO Forged Steel Y-Pattern Lift Check Valves Cv Values NPS 800 1500 2500 1/2 4 4 3 3/4 11 11 6 1 13 14 12 1-1/4 -- -- -- 1-1/2 36 34 27 2 67 67 36 Table applies to both piston and ball check valves. TC9308-4 57 V. HOW TO ORDER ALL CAMERON’S NEWCO PRODUCTS Figure Number The figure number shown below identifies specific valve configuration details of Cameron’s NEWCO valves such as valve type, pressure class, end connections, body/bonnet and trim materials, and special features. Please specify end connections, body materials and trims not listed below. When placing an order, please refer to the respective product section of the catalog for size availability. A detailed description must be included with any special orders. TC9308-4 58 Type 1 2 3 4 5 6 7 = = = = = = = Pressure Class 1 2 3 6 8 9 15 16 25 26 45 Gate, OS&Y Globe/Globe Stop Check, OS&Y Swing/Tilting Disc Check Piston Check Ball Gate, NRS Angle/Angle Stop Check, OS&Y = = = = = = = = = = = 150 125 300 600 800 900 1500 1690 2500 2680 4500 End Connections F J S T W X = = = = = = Flanged RTJ Socket Weld Threaded Butt Weld Threaded x Socket Weld Trim Material Fig.18T-FS2 _ _ 1 2 3 4 4/2 4/3 5 5/2 6 7 A7 8 9 = = = = = = = = = = = = = Suffix Letters Body/Bonnet Material A20 CB CC C5 C6 C9 C12 12A CF3 C3M CF8 C7L C8M C8C CT DI FS F3M F5 F7 F7L F11 F22 F9 F91 F8 F8M F8C IB LCC LF2 MO SPL = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = TC9308-4 ASTM A351, CN7M = Cast Alloy 20 ASTM A216, WCB = Cast Carbon Steel ASTM A216, WCC = Cast Carbon Steel ASTM A217, C5 = Cast Alloy Steel (5% Chrome, .5% Moly) ASTM A217, WC6 = Cast Alloy Steel (1.25% Chrome, .5% Moly) ASTM A217, WC9 = Cast Alloy Steel (2.25% Chrome, 1% Moly) ASTM A217, C12 = Cast Alloy Steel (9% Chrome, 1% Moly) ASTM A217, C12A = Cast Alloy Steel (9% Chrome, 1% Moly, V) ASTM A351, CF3 = Cast Stainless Steel ASTM A351, CF3M = Cast 316L Stainless Steel ASTM A351, CF8 = Cast 304 Stainless Steel ASTM A351, CG3M = Cast 317L Stainless Steel ASTM A351, CF8M = Cast 316 Stainless Steel ASTM A351, CF8C = Cast 347 Stainless Steel ASTM A351, CG8M = Cast 317 Stainless Steel ASTM A395 = Cast Ductile Iron ASTM A105 = Forged Carbon Steel ASTM A182, F316L = Forged 316 Stainless Steel ASTM A182, F5 = Forged Alloy Steel (5% Chrome, .5% Moly) ASTM A182, 317 = Forged 317 Stainless Steel ASTM A182, F317L = Forged 317L Stainless Steel ASTM A182, F11 = Forged Alloy Steel (1.25% Chrome, .5% Moly) ASTM A182, F22 = Forged Alloy Steel (2.25% Chrome, 1% Moly) ASTM A182, F9 = Forged Alloy Steel (9% Chrome, 1% Moly) ASTM A182, F91 = Forged Alloy Steel (9% Chrome, 1% Moly, V) ASTM A182, F304 = Forged 304 Stainless Steel ASTM A182, F316 = Forged 316 Stainless Steel ASTM A182, F321 = Forged 321 Stainless Steel ASTM A126, CLB = Cast Iron ASTM A352, LCC = Cast Low Temperature Carbon Steel ASTM A350, LF2 = Forged Low Temperature Carbon Steel ASTM A414, M35 = Cast NI Cu (Monel***) Special (Customer to specify) 59 BP BS CL CR CW EB FP FS GI GO HB HP HO INT LD LL LV MO NC OL OX PO PS PT QS RP SC SL SPL TD TF TM VP VL VP VT WB Y * API Trim = CR13................................ 1, 4, 8A CR13/HF**.............................8 CR13/FHF**...........................5 316........................................10 316/HF**..............................12 316/FHF**............................16 NI Cu (Monel***).................9 Monel/HF**.........................11 Alloy 20................................13 Bronze................................ N/A Aluminum Bronze............ N/A Iron..................................... N/A Special (Customer to Specify) = By Pass = Bellows Seal = Chlorine Service = Cryogenic Service = Chain Wheel = Extended Body = Full Port = Fire Safe = Grease Injection = Gear Operated = Horizontal Ball Check = Horizontal Piston Check = Hydraulic Operator = Integral Flanged = Locking Device = Locking Loop = Live Load Packing = Motor Operated = NACE MR0103 Compliant = Outside Weight & Lever = Oxygen Service = Pneumatic Operator = Pressure Seal Bonnet = PTFE Seats = QuadroSphere = Regular Port = Stop Check = Spring Loading = Special (Customer to specify) = Tilting Disc Check = Teflon* Insert = Trunnion Mounted = Vertical Ball Check = Vertical Lift Check = V-Port Disc = Viton* Insert = Welded Bonnet = Y Pattern = Viton and Teflon are registered trademarks of DuPont Company **HF = Hardfaced - AWS 5.13 Class COCRA *** = Monel is a registered trademark of International Nickel Company NOTES: TC9308-4 60 VI. INDUSTRY STANDARDS TYPICALLY USED IN VALVE MANUFACTURING (For Reference Only) British Standards Institute (BS) ISO 9001: 2000 RWTUV approved Newmans for design, manufacture, sales, & service of industrial valves under certificate registration number #08-1016 ISO 14001: 2004 The Newmans/Yancheng Manufacturing Team has passed the TUV-USA ISO 14001-2004 Certification Audit. All facilities inclusive of two (2) Foundries (Lost Wax and Sand Cast), Ball Valve Factory, Final Processing Center and Warehouses 15 & 16. BS 1414 (1975, R’ 91) - Gate, wedge & double disk valves: steel BS 1868 (1975, R’ 91) - Check valves: steel BS 1873 (1975, R’ 91) - Globe & check valves: steel BS 2080 (1989) obsolete - Flanged & buttweld end steel valves BS 5146 - (withdrawn) Replaced by BS 6755 p.1 steel valves testing (1986) & BS 6755 p.2 (1984) BS 5152 (1974, R’ 91) - Globe & check: cast iron BS 5153 (1974, R’ 91) - Check: cast iron BS 5159 (1974, R’ 91) - Ball: cast iron & carbon steel BS 5160 (1974, R’ 91) - Globe & check: steel BS 5163 (1986, R’ 91) - Gate, wedge & double disk: cast iron BS 5351 (1986, R’ 91) - Ball: steel BS 5352 (1986, R’ 91) - Globe & check: steel BS 5418 - (withdrawn) Replaced by BS EN 19 (1992) marking: general purpose industrial BS 5840 (1980, R’ 91) - Valve mating details for actuator operation BS 6364 (1984, R’ 91) - Cryogenic BS 6683 (1985, R’ 91) - Guide: installation & use of valves BS 6755: Part 1 (1986, R’ 91) - Specification for production pressure testing requirements BS 6755: Part 2 (1987) - Specification for fire type-testing requirements BS EN 19 (1992) - Marking of general purpose industrial valves American Petroleum Institute (API) API RP 574 (1998) - Inspection practices for piping system components API 589 (1998) - Fire test for evaluation of valve stem packing API RP 591 (2003) - Process valve qualification procedure API 594 (2004) - Check valves-flanged, lug, wafer & buttwelding API 597 (1981) - Steel venturi gate valves, flanged, buttwelding ends API 598 (2004) - Valve inspection & testing API 599 (2002) - Metal plug valves - flanged, welding ends API 601 (1988) - Metallic gaskets for raised-face pipe flanges & flanged connections (doublejacketed corrugated & spiral wound) API 600 (2001) - Bolted bonnet steel gate valves for petroleum & natural as industries “ISO adoption from ISO 10434” API 602 (2005) - Steel gate, globe, & check valves for sizes DN100 and smaller for the petroleum & natural gas industries API 603 (2001) - Corrosion-resistant, bolted bonnet gate valves-flanged & buttweld ends API 604 (1981) - Ductile iron gate valves, flanged ends API 605 (1988) - Large-diameter carbon steel flanges (nominal pipe sizes 26” through 60”, classes 75, 150, 300, 400, 600, & 900 (replaced by ANSI/ASME B16.47) API 606 (1989) - Compact steel gate valves, extended body (included in API 602) fire test for soft-seated quarter-turn valves “ISO adoption from ISO 10497-5 2004” API 607 (2005) - Fire test for soft-seated quarter-turn valves “ISO adoption from ISO 10497-5 2004” API 608 (2002) - Metal ball valves, flanged, threaded, & welding ends API 609 (2004) - Butterfly valves-double flanged, lug- & wafer-type API RP 941 (2004) - Steel for hydrogen service at elevated temperatures & pressures in petroleum refineries & petrochemical plants API RP 520 (2000), Part 1 - Sizing, selection & installation of pressure relieving devices in refineries API RP 520 (2003), Part 2 - Sizing, selection & installation of pressure relieving devices in refineries devices in refineries API Spec 6A (2005) - Specification for wellhead & christmas tree equipment API Spec 6D (2005) - Specifications for pipeline valves API Spec 14D (1994) - Specifications for wellhead surface safety valves & underwater safety valves for offshore service API 5B (2004) - Threading, gauging thread inspection of coring, tubing, & line pipe threads API 6AM (2003) - Material toughness API 6FA (1999) - Fire test for valves API 6FC (1999) - Fire test for valves with backseats API 6FD (1995) - Specification for fire test for check valves API Q1 (2003) - Specification for quality programs for the petroleum, petrochemical, & natural gas Canadian Standards Association B51-97 - Boiler, pressure vessel, & pressure piping code Z245.15-96 - Steel valves CAN3-z299.4-85 (reaffirmed 1997) - Quality assurance program - Category 4 CAN3-z299.3-85 (reaffirmed 1997) - Quality assurance program - Category 3 International Organization for Standardization ISO 5211/1 (2001) - Industrial valves- part-turn actuator attachments ISO 5211/2 (2001) - Part-turn valve actuator attachment-flange & coupling performance characteristics ISO 5211/3 (2001) - Part-turn valve actuator attachment-dimensions of driving components ISO 5752 (1982) - Metal valves for use in flanged pipe systems face-to-face & center-to-face dimensions ISO 9000 (2005) - Quality management systems and fundamentals & vocabulary ISO 10012-1 (1992) - Quality assurance requirements for measuring equipment Manufacturers Standardization Society ASNT-TC-1A (1996) - Recommended practice no. SNT-TC-1A 1996 SP-6 (2001) - Standard finishes for contact faces of pipe flanges & connecting-end flanges of valves & fittings SP-9 (r2005) - Spot facing for bronze, iron & steel flanges SP-25 (1998) - Standard marking system for valves, fittings, flanges & unions SP-42 (2004) - Class 150 corrosion resistant gate, globe, angle, & check valves with flanged & buttweld ends SP-44 (2001) - Steel pipeline flanges SP-45 (2003) - Bypass & drain connections SP-51 (2003) - Class 150/w corrosion resistant cast flanges & flanged fittings SP-53 (2002) - Quality standard for steel castings & forgings for valves, flanges, & fittings & other piping components: magnetic particle exam method SP-54 (2002) - Quality standard for steel castings for valves, flanges, & fittings and other piping components: radiographic examination method SP-55 (2001) - Quality standard for steel castings for valves, flanges other piping components-visual method for evaluation of surface irregularities SP-60 (2004) - Connecting flange joint between tapping sleeves & tapping valves SP-61 (2003) - Pressure testing of steel valves SP-65 (2004) - High pressure chemical industry flanges & threaded stubs for use with lens gaskets SP-67 (2000A) - Butterfly valves SP-69 (2003) - ANSI/MSS edition pipe hangers & supports, selection & application SP-70 (1998) - Cast iron gate valves, flanged & threaded ends SP-71 (1997) - Gray iron swing check valves, flanged & threaded ends SP-72 (1999) - Ball valves with flanged or butt-welding ends for general service SP-79 (2004) - Socket-welding reducer inserts SP-81 (2001) - Stainless steel, bonnetless, flanged knife gate valves SP-82 (1992) - Valve pressure testing methods SP-84 (1990) - Valves - socket welding & threaded ends SP-85 (2002) - Cast iron globe & angle valves, flanged & threaded ends SP-86 (2002) - Guidelines for metric data in standards for valves, flanges, fittings & actuators SP-88 (r2001) - Diaphragm valves SP-91 (1992) - Guidelines for manual operation of valves SP-92 (1999) - MSS valve user guide SP-93 (r2004) - Quality standard for steel castings & forgings for valves, flanges & fittings & other piping components- liquid penetrant exam method SP-94 (r2004) - Quality standard for ferritic & martensitic steel castings for valves, flanges, & fittings and others piping components - ultrasonic exam method SP-96 (r2005) - Guidelines on terminology for valves & fittings SP-98 (2001) - Protective coatings for the interior of valves, hydrants, & fittings SP-99 (r2005) - Instrument valves SP-101 (r2001) - Part-turn valve actuator attachment-flange and driving component dimensions & performance characteristics SP-102 (r2001) - Multi-turn valve actuator attachment: flange and driving component dimensions & performance characteristics SP-110 (1996) - Ball valves threaded, socket-welding, solder joint, grooved, & flared ends SP-117 (2002) - Bellows seals for globe & gate valves SP-118 (2002) - Compact steel globe and check valves-flanged, flangeless, threaded & welding ends (chemical & petroleum refinery service) SP-120 (2002) - Flexible graphite packing system for rising stem steel valves (design requirements) SP-121 (R2002) - Qualification testing methods for stem packing for rising stem steel valves American Society for Testing and Materials (ASTM) National Association of Corrosion Engineers (NACE) American Society of Mechanical Engineers (ASME) ASME Code (1997 addenda) - Boiler & pressure vessel code ASME A13.1 (1996) - Scheme for the identification of piping systems ASME B1.1 (2003) Unified inch screw threads, UN, & UNR thread form ASME B1.5 (1997) - ACME screw threads ASME B1.7M (1984) - Nomenclature, definitions, & letter symbols for screw threads ASME B1.8 (1988) - Stub ACME screw threads ASME B1.12 (1987) - Class 5 interference - fit thread ASME B1.20.1 (1983) - Pipe threads, general purpose, inch ASME B1.20.3 (1976) - Dry-seal pipe threads, inch ANSI/ASME B16.1 (1998) - Cast iron pipe flanges & flanged fittings ANSI/ASME B16.5 (2003) - Pipe flanges & flanged fittings: NPS 1/2” through 24” ASME B16.9 (2003) - Factory made wrought steel buttwelding fittings ANSI/ASME B16.10 (2002) - Face-to-face & end-to-end dimensions of valves ASME B16.11 (2001) - Forged fittings, socket welding & threaded ASME B16.20 (1998) - Metallic gaskets for pipe flanges: ring joint spiral wound & jacketed ASME B16.21 (2005) - Non-metallic flat gaskets for pipe flanges ASME B16.25 (2003) - Buttwelding ends ANSI/ASME B16.33 (2002) - Manually operated metallic gas valves for use in gas piping systems up to 125 PSI (sizes NPS 1/2” through 2” ) ANSI/ASME B31.1 (2004) - Power piping ANSI/ASME B31.3 (2004) - Process piping ANSI/ASME B16.34 (2004) - Valves flanged, threaded & welding end ANSI/ASME B16.36 (1996) - Orifice flanges ANSI/ASME B16.38 (1985) - Large metallic valves for gas distribution (manually operated, NPS 2-1/2” through 12”, 125 PSIG maximum) ANSI/ASME B16.42 (1998) - Ductile iron pipe flanges & flanged fittings: classes 150 & 300 ANSI/ASME B16.47 (1996) - Large diameter steel flanges ANSI B17.1 (1967, R’ 89) - Keys & keyseats ANSI B18.2.2 (1987) - Square & hex nuts ASME B31.4 (2002) - Pipeline transportation systems for liquid hydrocarbons & other ammonia & alcohols ANSI/ASME B31.8 (2003) - Gas transmission & distribution piping systems ANSI/ASME B36.10 (2004) - Welded & seamless wrought steel pipe ANSI/ASME B36.19 (2004) - Stainless steel pipe ANSI FCI-2 (1991) - Control valve seat leakage American Society Non-destructive Test (ASNT) MR0175 (2005) - Sulfide stress cracking resistant metallic materials for oil field equipment MR0103 (2005) - Materials resistant to sulfide street cracking in corrosive petroleum refining environments TC9308-4 61 NOTES: TC9308-4 62 NOTES: TC9308-4 63 VALVES & MEASUREMENT 13127 Trinity Dr. Stafford, Tx 77477 Toll Free 800.231.3505 Tel 281.302.4900 Fax 281.302.4801 Learn more about NEWCO valves at: www.c-a-m.com/newco [email protected] ENVIRONME N XCELLEN LE CE TA TH SAFETY AL A HE ND CA HSE Policy Statement At Cameron, we are committed ethically, financially and personally to a working environment where no one gets hurt, nothing gets harmed. MERON © 2013 Cameron • Produced by Technical Publications, Houston, TX, USA