10/2/2022 | Page 1 of 4 Thermoplastic Valves, Inc. 53 South 7th St. Emmaus, PA 18049 United States of America Phone: 610-967-6388 Fax: 610-967-6448 Toll-free: 866-242-5890 Email: [email protected] Website: http://www.tvivalves.com ITEM # DN-6, 6 INCH (IN) COMPACT BALL VALVES Thermoplastic compact ball valve (6") shall have a one piece PVC molded body with socket or threaded end connections. Valve is full port for lowest possible pressure loss. Seat shall be comprised of Polytetrafluoroethylene (PTFE) and seal of EPDM. Every valve is fully pressure and cycle tested to insure quality. Valve shall have a one piece self centering ball and stem design for leak tight operation. Specifications | ANSI Dimensions | Material of Construction | Construction | Design Advantages | Applications | Testing Procedure Specifications Brands TVI Flow Coefficient Value (Cv) 1390 Body/Ball/Stem Polyvinyl Chloride (PVC), ASTM D-1784 ANSI Dimensions Size 6 in Dimension D1 5.9 in Socket Dimension d 6.65 in 10/2/2022 | Page 2 of 4 Thread Dimension d 5.9 in Dimension P 3.03 in Dimension L 14.04 in Dimension K 14.23 in Dimension H 8.15 in Test Pressure 225 psi Working Pressure 150 psi Material of Construction Part - Body Pcs - 1 Material - Unplasticized Polyvinyl Chloride (UPVC) Part - Ball Pcs - 1 Material - Unplasticized Polyvinyl Chloride (UPVC) Part - Seat Carrier Pcs - 1 Material - Unplasticized Polyvinyl Chloride (UPVC) Part - Stem Pcs - 1 Material - Unplasticized Polyvinyl Chloride (UPVC) Part - End Connector Pcs - 1 Material - Unplasticized Polyvinyl Chloride (UPVC) Part - Seat Carrier O-ring Pcs - 1 Material - Ethylene Propylene Diene Monomer (EPDM) Part - Stem O-ring Pcs - 2 Material - Ethylene Propylene Diene Monomer (EPDM) Part - Body O-ring 10/2/2022 | Page 3 of 4 Materials of Construction Pcs - 2 Material - Ethylene Propylene Diene Monomer (EPDM) Part - Seat Pcs - 2 Material -Polytetrafluoroethylene (PTFE) Part - Activities Jumper Pcs - 1 Material - Unplasticized Polyvinyl Chloride (UPVC) Part - Handle Lever Pcs - 1 Material - Polypropylene (PP) Part - Handle Pcs - 1 Material - Polypropylene (PP) Part - Jumper Pcs - 1 Material - Polypropylene (PP) Part - Washer Pcs - 1 Material - Polypropylene (PP) Part - Bolt Pcs - 1 Material - SUS Stainless Steel Part - Cap Pcs - 1 Material - Polypropylene (PP) Construction Seat Polytetrafluoroethylene (PTFE), Dupont Dow Elastomers Seals (O-Rings) Ethylene Propylene Diene Monomer (EPDM) Manual Lever Acrylonitrile Butadiene Styrene (ABS), ASTM D-1788 Socket ASTM-D-2467 (Polyvinyl Chloride (PVC), SCH-80) Threaded ASTM-D-2467 (Polyvinyl Chloride (PVC), SCH-80) 10/2/2022 | Page 4 of 4 Design Advantages Design Advantages Economically priced Light weight & maintenance-free makes for an easy installation Durable construction, low torque with self lubricating Polytetrafluoroethylene (PTFE) seat Body Construction - light Weight, chemical resistant, noncorrosive Applications Applications Water and Waste Treatment Chemical Industry Environmental Industry Process Industry Systems Engineering Testing Procedure Testing Procedure Every valve is tested for bubble tight shutoff prior to leaving the factory. Pressure testing preformed on Polyvinyl Chloride (PVC)/Ethylene Propylene Diene Monomer (EPDM) valves at 73 ºF water temperature, non-shock.