CDX-GT40U/GT40UW/GT42UE/ GT44U/GT45U/GT47UE US Model SERVICE MANUAL CDX-GT40U/GT40UW Canadian Model Ver. 1.4 2012.07 CDX-GT40U AEP Model UK Model CDX-GT40U/GT44U E Model CDX-GT45U Russian Model CDX-GT40U/GT42UE/GT47UE Indian Model Photo: CDX-GT40U: AEP, UK model CDX-GT44U • The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism NEW AUDIO POWER SPECIFICATIONS (US model) CEA2006 Standard Power Output: 17 Watts RMS 4 at 4 Ohms < 1 % THD + N SN Ratio: 80 dBA (reference: 1 Watt into 4 Ohms) CD Drive Mechanism Type MG-101CA-188 Optical Pick-up Name DAX-25A SPECIFICATIONS Tuner section FM Tuning range: US, CND, AR model: 87.5 – 107.9 MHz AEP, UK, EA model: 87.5 – 108.0 MHz E, MX, KR, IND model: 87.5 – 108.0 MHz (at 50 kHz step) 87.5 – 108.0 MHz (at 100 kHz step) 87.5 – 107.9 MHz (at 200 kHz step) RU model: FM1/FM2: 87.5 – 108.0 MHz (at 50 kHz) FM3: 65 – 74 MHz (at 30 kHz) FM tuning step: E, MX, KR, IND model: 50 kHz/100 kHz/200 kHz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 25 kHz Usable sensitivity: 8 dBf Selectivity: 75 dB at 400 kHz Signal-to-noise ratio: 80 dB (stereo) Separation: 50 dB at 1 kHz Frequency response: 20 – 15,000 Hz AM (US, CND, E, MX, AR, KR, IND model) Tuning range: US, CND, AR model: 530 – 1,710 kHz E, MX, KR, IND model: 531 – 1,602 kHz (at 9 kHz step) 530 – 1,710 kHz (at 10 kHz step) AM tuning step: E, MX, KR, IND model: 9 kHz/10 kHz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: US, CND, AR model: 9,115 kHz or 9,125 kHz/5 kHz E, MX, KR, IND model: 9,124.5 kHz or 9,115.5 kHz/4.5 kHz (at 9 kHz step) 9,115 kHz or 9,125 kHz/5 kHz (at 10 kHz step) Sensitivity: 26 V MW/LW (AEP, RU, UK model) MW (EA model) Tuning range: MW: 531 – 1,602 kHz LW: 153 – 279 kHz (AEP, RU, UK model) Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 9,124.5 kHz or 9,115.5 kHz/4.5 kHz Sensitivity: MW: 26 V LW: 45V (AEP, RU, UK model) SW (EA model) Tuning range: SW1: 2,940 – 7,735 kHz SW2: 9,500 – 18,135 kHz (except for 10,140 – 11,575 kHz) Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 9,124.5 kHz or 9,115.5 kHz/4.5 kHz Sensitivity: 26 μV CD player section Signal-to-noise ratio: 120 dB Frequency response: 10 – 20,000 Hz Wow and flutter: Below measurable limit USB Player section Interface: USB (Full-speed) Maximum current: 1 A Power amplifier section Outputs: Speaker outputs Speaker impedance: 4 – 8 ohms Maximum power output: US, CND, E, EA, MX, AR, KR, IND model: 52 W 4 (at 4 ohms) AEP, RU, UK model: 45 W 4 (at 4 ohms) – Continued on next page – US, Canadian, E, Mexican, Argentina, Korean, Indian model FM/AM COMPACT DISC PLAYER AEP, Russian, UK model FM/MW/LW COMPACT DISC PLAYER Saudi Arabia model FM/MW/SW COMPACT DISC PLAYER 9-893-214-05 2012G33-1 © 2012.07 Sony Corporation Published by Sony Techno Create Corporation CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.2 General Outputs: Audio outputs terminal (rear/sub switchable) US, CND, E, EA, MX, AR, KR, IND model: Power antenna (aerial)/Power amplifier control terminal (REM OUT) AEP, RU, UK model: Power antenna (aerial) relay control terminal Power amplifier control terminal Inputs: Remote controller input terminal Antenna (aerial) input terminal AUX input jack (stereo mini jack) USB signal input connector Power requirements: 12 V DC car battery (negative ground (earth)) Dimensions: Approx. 178 × 50 × 179 mm (7 1/8 × 2 × 7 1/8 in.) (w/h/d) Mounting dimensions: Approx. 182 × 53 × 162 mm (7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d) Mass: Approx. 1.2 kg (2 lb. 11 oz.) Supplied accessories: Remote commander: RM-X211 (US, CND, E, EA, MX, AR, KR, IND model) Parts for installation and connections (1 set) Design and specifications are subject to change without notice. • Abbreviation AR : Argentina model CND : Canadian model EA : Saudi Arabia model IND : Indian model KR : Korean model MX : Mexican model RU : Russian model Except US, Canadian model: TABLE OF CONTENTS 1. 2. NOTES ON CHIP COMPONENT REPLACEMENT • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. 2 3 GENERAL Connections .................................................................... 3. DISASSEMBLY 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. 3-10. 3-11. Sub Panel Assy ............................................................... CD Mechanism Block ..................................................... Main Board ..................................................................... Servo Board .................................................................... Chassis (T) Sub Assy ...................................................... Roller Arm Assy.............................................................. Chassis (OP) Assy ........................................................... Chucking Arm Sub Assy ................................................. Sled Motor Assy.............................................................. Optical Pick-up Section .................................................. Optical Pick-up ............................................................... 4. DIAGRAMS 4-1. Block Diagram - Main Section - ..................................... 4-2. Block Diagram - Display Section - ................................. 4-3. Printed Wiring Board - Main Section (1/2) (Except Saudi Arabia model) -........................................ 4-4. Printed Wiring Boards - Main Section (2/2) (Except Saudi Arabia model) -........................................ 4-5. Schematic Diagram - Main Section (1/5) - ..................... 4-6. Schematic Diagram - Main Section (2/5) - ..................... 4-7. Schematic Diagram - Main Section (3/5) - ..................... 4-8. Schematic Diagram - Main Section (4/5) - ..................... 4-9. Schematic Diagram - Main Section (5/5) - ..................... 4-10. Printed Wiring Board - Key Section - ............................. 4-11. Schematic Diagram - Key Section - ............................... 5. This label is located on the bottom of the chassis. SERVICE NOTE ...................................................... 8 13 14 14 15 16 16 17 17 18 19 19 21 22 24 25 26 27 28 29 30 31 32 EXPLODED VIEWS 5-1. Main Section ................................................................... 43 5-2. Front Panel Section ......................................................... 44 5-3. CD Mechanism Section (MG-101CA-188) .................... 45 6. ELECTRICAL PARTS LIST.................................. 46 Note: Refer to SUPPLEMENT-1 for printed wiring board of MAIN board (Saudi Arabia model). CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 SECTION 1 SERVICE NOTE UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. NOTE FOR REPLACEMENT OF THE SERVO BOARD When repairing, the complete SERVO board should be replaced since any parts in the SERVO board cannot be repaired. NOTE FOR REPLACEMENT OF THE SENSOR BOARD When the SENSOR board is defective, exchange the MECHANICAL BLOCK (Z) ASSY 08 (Former type) or MECHANICAL BLOCK (11CA) ASSY (New type). Note: As for the mechanism deck (MG-101CA-188) carried in this unit, component parts have been changed from the midway of production. When you perform repair exchange of the mechanism deck (MG-101CA-188), refer to “ABOUT THE MG-101CA-188 OF FORMER AND NEW” on page 6. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. TEST DISCS Use following TEST DISC when this unit confirms the operation and checks it. Part No. Description 3-702-101-01 4-225-203-01 DISC (YEDS-18), TEST (for CD) DISC (PATD-012), TEST (for CD) CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block. optical pick-up semi-fixed resistor 3 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CN700) and the SERVO board (CN401) with the jig cable. Jig cable: Part No. Description A-1818-424-A EXTENSION CABLE (CD MECHA) MAIN board (CN700) extension cable (CD mecha) SERVO board (CN401) NOTE FOR REPLACEMENT OF THE USB CONNECTOR (CN902) AND THE AUX JACK (J901) To replace the USB connector and the AUX jack requires alignment. 1. Insert the USB connector and the AUX jack into the front panel. 2. Place the KEY board on the front panel and align the terminals of the USB connector and the AUX jack with the holes in the KEY board. 3. Solder the seven terminals of the connector and three terminals of the jack. CLEANING THE CONNECTORS The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel and clean the connectors with a cotton swab. Do not apply too much force. Otherwise, the connectors may be damaged. KEY board Notes t For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. t Never touch the connectors directly with your fingers or with any metal device. USB (socket) connector front panel 4 AUX jack CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.2 NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING When the MAIN board or system controller (IC501) is replaced, the destination setting is necessary. • Method of operation by remote commander OFF AT T MENU SOURCE 1. Destination Setting Set destination according to the procedure below. SOUND MODE + ENTER – 1-1. Setting the Destination Code 1. In the state of source off (the clock is displayed), enter the test mode by pressing the buttons in order of the [4] t [5] t [6] (press only the [6] button for two seconds). 2. In the state in which the system controller version is displayed on the liquid crystal display, enter the destination setting mode by pressing the buttons in order of the [SEEK +] t [SEEK –] t [PUSH ENTER/SELECT]. 3. Input the alphanumeric character of 6 digits of “F XXXXXX” displayed on the liquid crystal display, and execute the destination setting. Note: Refer to following “1-3. Entering the Destination Code” for operation method. 4. The resetting operation is executed by pressing the [SOURCE/ OFF] button for 1 second after the setting ends, and the unit returns to the normal condition. 1-2. Display in Destination Setting Mode OP5 OP4 OP3 OP2 OP1 OP0 12 digits F X X X X X X 1-3. Entering the Destination Code • Method of operation by main unit DSPL/ SCRL PTY 2 PA US E 5 + VO L – 1. Press the [ ] or [ ] button, and select the alphanumeric character of “0 to F”. 2. The digit advances by pressing the [ ] button. The digit returns by pressing the [ ] button. 3. The setting is completed by pressing the [ENTER] button, and the initialization operation is done. 1-4. Destination Code Model Destination OP5 OP4 OP3 OP2 OP1 OP0 CDX-GT40U US, Canadian 0 1 C 3 0 2 CDX-GT40UW CDX-GT40U AEP, UK 0 1 C 3 0 1 CDX-GT44U CDX-GT40U 0 1 E 3 0 7 CDX-GT42UE Russian CDX-GT47UE E, Mexican, CDX-GT44U Korean, 0 1 C B 0 0 CDX-GT45U Indian CDX-GT45U Saudi Arabia 0 1 C B 0 4 CDX-GT45U Argentina 0 1 C B 0 3 2. Confirmation After Destination Setting Execute the following operation after completing the destination setting, and confirm a correct destination was set. 1. Rotate the control dial, and select the alphanumeric character of “0 to F”. 2. The digit advances by pressing the [PUSH ENTER/SELECT] or [SEEK +] button. The digit returns by pressing the [ ] or [SEEK –] button. 3. The setting is completed by pressing the [PUSH ENTER/ SELECT] button, and the initialization operation is done. Destination setting checking method: 1. In the state of source off (the clock is displayed on the liquid crystal display), enter the test mode by pressing the buttons in order of the [4] t [5] t [6] (press only the [6] button for two seconds). 2. In the state in which the system controller version is displayed on the liquid crystal display, enter the destination setting value display mode by pressing the [DSPL] button. 3. Confirm the alphanumeric character of 6 digits of “F XXXXXX” displayed in liquid crystal display is an value correctly input. 4. The resetting operation is executed by pressing the [SOURCE/ OFF] button for 1 second after the confirming ends, and the unit returns to the normal condition. 5 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 ABOUT THE MG-101CA-188 OF FORMER AND NEW As for the mechanism deck (MG-101CA-188) carried in this unit, component parts have been changed from the midway of production. When you perform repair exchange of the mechanism deck (MG-101CA-188), please be sure to work, after referring to the following figure and checking former and new. • New/Former Discrimination As shown in the following figure, please check the SERVO board side of the mechanism deck (MG-101CA-188). Former type New type Flexible board can be seen. Flexible board cannot be seen. SERVO board (double-sided board) • SERVO board (one side board) New/Former Compatibility Mechanical block assy Complete SERVO board MECHANICAL BLOCK ASSY 6 COMPLETE SERVO BOARD Judgment New type + New type = New type + Former type = OK OK Former type + New type = NG Former type + Former type = OK CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD In this set, the LCD driver IC (IC901) on the KEY board has been changed in the midway of production. The following changes are performed by this change. • • • • Change of the KEY board (suffix-21/-22) (Refer to supplement-2) Change of part No. of the FRONT PANEL OVERALL ASSY (Refer to page 44, 52 and 53) Change of part No. of the complete MAIN board (Refer to page 43 and 48) Change of part for Ref No. IC501 on the MAIN board (Refer to page 50) Since all the above-mentioned change is synchronous change, there is not compatibility of new type/former type in the front panel side and main unit side. Do the work after necessarily referring to following “New/former discrimination”. Serial number Model Destination Former type New type US and Canadian models* 1864691 or smaller 1864692 or lager Canadian model (for CXS-GT4016F) 1554521 or smaller 1554522 or lager AEP and UK models 1885791 or smaller 1885792 or lager Russian model 1822499 or smaller 1822500 or lager CDXGT40UW US model 1864116 or smaller 1864117 or lager CDXGT42UE Russian model 1850792 or smaller 1850793 or lager AEP and UK models 1939738 or smaller 1939739 or lager Indian model 1865831 or smaller 1865832 or lager E model 1811434 or smaller 1811435 or lager Saudi Arabia model 1878981 or smaller 1878982 or lager Mexican model 1838226 or smaller 1838227 or lager Argentina model 1798061 or smaller 1798062 or lager Korean model 1826514 or smaller 1826515 or lager Russian model 1858886 or smaller 1858887 or lager CDXGT40U CDXGT44U Note: When the parts of new front panel and the parts of old main unit are combined, this unit does not operate normally. New/former discrimination: Three kinds of following distinguish methods exist. • CDXGT45U Distinguish method by serial number printed on the model number label (Refer to right side for the serial number). – Main unit (Bottom side) – Model number label CDXGT47UE *CXS-GT4016F (US model) is Former type only. Displayed characters/values are example. • Distinguish method by part No. printed on the KEY board – KEY Board (Side A) – Former type : 1-884-821-11 New type : 1-884-821-21 or 1-884-821-22 • Distinguish method by LCD driver IC (IC901) on the KEY board – KEY Board (Side B) – IC901 Former type : LC75839 New type : PT6587-LQ 7 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE SECTION 2 GENERAL This section is extracted from instruction manual. CONNECTIONS • CDX-GT40U: US, Canadian model/GT40UW * 1 RCA pin cord (not supplied). * 2 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. * 3 Separate adaptor may be required. * 1 Cordon à broche RCA (non fourni). * 2 AUDIO OUT peut être commuté sur SUB ou REAR. Pour obtenir plus de détails, reportez-vous au mode d’emploi fourni. * 3 L’utilisation d’un adaptateur pourrait être nécessaire. *1 REMOTE IN * 3 from car antenna (aerial) à partir de l’antenne du véhicule REM OUT Max. supply current 0.4 A Courant max. fourni 0,4 A REAR / SUB AUDIO OUT * 2 Fuse (10 A) Fusible (10 A) Blue/white striped Rayé bleu/blanc 2 White Blanc Left Gauche White/black striped Rayé blanc/noir Gray Gris Right Droit Black Noir Gray/black striped Rayé gris/noir Green Vert Left Gauche Red Rouge ACC Green/black striped Rayé vert/noir Purple Violet Right Droit Purple/black striped Rayé violet/noir Connection diagram Schéma de raccordement 1 To a metal surface of the car 1 À un point métallique de la voiture 2 To the power antenna (aerial) control lead or 2 Au câble de commande d’antenne électrique ou First connect the black ground (earth) lead, then connect the yellow and red power supply leads. power supply lead of antenna (aerial) booster Branchez d’abord le câble de mise à la masse noir et, ensuite, les câbles d’alimentation jaune et rouge. au câble d’alimentation de l’amplificateur d’antenne Notes It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). When your car has a built-in FM/AM antenna (aerial) in the rear/ side glass, see “Notes on the control and power supply leads.” Remarques To AMP REMOTE IN of an optional power amplifier Au niveau de AMP REMOTE IN de l’amplificateur de puissance en option This connection is only for amplifiers. Connecting any other system may damage the unit. 3 To the +12 V power terminal which is energized Ce raccordement s’applique uniquement aux amplificateurs. Le branchement de tout autre système risque d’endommager l’appareil. in the accessory position of the ignition switch Notes If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. When your car has a built-in FM/AM antenna (aerial) in the rear/ side glass, see “Notes on the control and power supply leads.” 3 À la borne d’alimentation +12 V qui est alimentée quand la clé de contact est sur la position accessoires Remarques 4 To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first. Notes on the control and power supply leads REM OUT lead (blue/white striped) supplies +12 V DC when you turn on the unit. When your car has built-in FM/AM antenna (aerial) in the rear/side glass, connect REM OUT lead (blue/white striped) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. S’il n’y a pas de position accessoires, raccordez la borne d’alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule. Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ». 4 À la borne d’alimentation +12 V qui est alimentée en permanence Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule. Remarques sur les câbles de commande et d’alimentation When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection Il n’est pas nécessaire de raccorder ce câble s’il n’y a pas d’antenne électrique ni d’amplificateur d’antenne, ou avec une antenne télescopique manuelle. Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ». Le câble REM OUT (rayé bleu/blanc) fournit une alimentation de +12 V CC lorsque vous mettez l’appareil en marche. Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le câble REM OUT (rayé bleu/blanc) ou le câble d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre détaillant. Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le câble d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt. Remarques sur le raccordement des haut-parleurs Avant de raccorder les haut-parleurs, éteignez l'appareil. Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité électrique adéquate pour éviter de les endommager. Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes du haut-parleur droit à celles du haut-parleur gauche. Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur. N’essayez pas de raccorder les haut-parleurs en parallèle. Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil. Pour éviter tout problème de fonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil possède un câble négatif commun (–) pour les haut-parleurs droit et gauche. Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil. Remarque sur le raccordement Si le haut-parleur et l’amplificateur ne sont pas raccordés correctement, le message « FAILURE » s’affiche. Dans ce cas, assurez-vous que les haut-parleurs et l’amplificateur sont bien raccordés. 8 Yellow Jaune BATTERY CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.2 • CDX-GT40U: AEP, UK model/GT44U: AEP, UK model *1 Hinweis zum Anschließen der Antenne If your car antenna (aerial) is an ISO (International Organization for Standardization) type, use the supplied adaptor 2 to connect it. First connect the car antenna (aerial) to the supplied adaptor, then connect it to the antenna (aerial) jack of the master unit. *2 RCA pin cord (not supplied). *3 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. *4 Separate adaptor may be required. Wenn Ihre Autoantenne der ISO -Norm (Internationale Normungsgemeinschaft) entspricht, schließen Sie sie mithilfe des mitgelieferten Adapters 2 an. Verbinden Sie zuerst die Autoantenne mit dem mitgelieferten Adapter und verbinden Sie diesen dann mit der Antennenbuchse des Hauptgeräts. *2 Cinchkabel (nicht mitgeliefert). 3 * AUDIO OUT kann zwischen SUB und REAR umgeschaltet werden. Näheres hierzu finden Sie in der mitgelieferten Bedienungsanleitung. *4 Möglicherweise ist ein separater Adapter erforderlich. *1 Nota per il collegamento dell’antenna Si votre antenne de voiture est de type ISO Se l’antenna dell’auto è di tipo ISO (International (Organisation internationale de normalisation), Organization for Standardization), utilizzare utilisez l’adaptateur fourni 2 pour la raccorder. l’adattatore 2 in dotazione per collegarla. Raccordez d’abord l’antenne de voiture à Collegare prima l’antenna della macchina l’adaptateur fourni et, ensuite, à la prise d’antenne all’adattatore in dotazione, quindi collegarla alla de l’appareil principal. presa dell’antenna dell’apparecchio principale. *2 Cordon à broche RCA (non fourni). *2 Cavo a piedini RCA (non in dotazione). *3 AUDIO OUT peut être commuté sur SUB ou REAR. *3 AUDIO OUT può essere impostato su SUB o su Pour obtenir plus de détails, reportez-vous au REAR. Per ulteriori informazioni, consultare il mode d’emploi. manuale di istruzioni per l’uso in dotazione. *4 Un adaptateur séparé peut être nécessaire. *4 Potrebbe essere necessario un adattatore separato. Fuse (10 A) Sicherung (10 A) Fusible (10 A) Fusibile (10 A) Zekering (10 A) Blue/white striped Blauweiß gestreift Rayé bleu/blanc Rigato blu e bianco Blauw/wit gestreept REMOTE IN * 4 3 from the car’s speaker connector vom Lautsprecheranschluss des Fahrzeugs du connecteur de haut-parleur de la voiture dal connettore dei diffusori dell’auto van de autoluidsprekeraansluiting from the car’s power connector vom Stromanschluss des Fahrzeugs du connecteur d’alimentation de la voiture dal connettore di alimentazione dell’auto van de autovoedingsaansluiting 1 2 Purple Violett Violet Viola Paars + Speaker, Rear, Right Lautsprecher hinten rechts Haut-parleur, arrière, droit Diffusore, posteriore, destro Luidspreker, achter, rechts 5 – Speaker, Rear, Right Lautsprecher hinten rechts Haut-parleur, arrière, droit Diffusore, posteriore, destro Luidspreker, achter, rechts 6 + Speaker, Front, Right Lautsprecher vorne rechts Haut-parleur, avant, droit Diffusore, anteriore, destro Luidspreker, voor, rechts 7 – Speaker, Front, Right Lautsprecher vorne rechts Haut-parleur, avant, droit Diffusore, anteriore, destro Luidspreker, voor, rechts 8 See “Power connection diagram” on the reverse side for details. Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern Sie dazu bitte um. 4 Voir le « Schéma de raccordement d’alimentation » au verso pour plus de détails. Per ulteriori informazioni, vedere “Diagramma dei collegamenti di alimentazione” che si trova sul retro. Zie "Voedingsaansluitschema" op de achterkant voor meer details. 5 Yellow Gelb Jaune Giallo Geel continuous power supply permanente Stromversorgung alimentation continue alimentazione continua continu voeding 7 Blue Blau Bleu Blu Blauw power antenna (aerial) control Motorantennensteuerung commande d'antenne électrique comando dell’antenna elettrica elektrische antenne 8 Red Rot Rouge Rosso Rood switched power supply geschaltete Stromversorgung alimentation commutée alimentazione commutata geschakelde voeding 3 Black Schwarz Noir Nero Zwart ground (earth) Masse masse terra aarding 4 amplifier A An AMP REMOTE IN des gesondert erhältlichen Endverstärkers If you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power supply lead 3 may damage the antenna (aerial). Notes on the control and power supply leads The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner, or when you activate the AF (Alternative Frequency) or TA (Traffic Announcement) function. When your car has built-in FM/MW/LW antenna (aerial) in the rear/ side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. A power antenna (aerial) without a relay box cannot be used with this unit. Warnung Wenn Sie eine Motorantenne ohne Relaiskästchen verwenden, kann durch Anschließen dieses Geräts mit dem mitgelieferten Stromversorgungskabel 3 die Antenne beschädigt werden. Hinweise zu den Steuer- und Stromversorgungsleitungen Memory hold connection Die Motorantennen-Steuerleitung (blau) liefert +12 V Gleichstrom, wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzsuche) oder die TA-Funktion (Verkehrsdurchsagen) aktivieren. Wenn das Fahrzeug mit einer in der Heck-/Seitenfensterscheibe integrierten FM (UKW)/MW/LW-Antenne ausgestattet ist, schließen Sie die Motorantennen-Steuerleitung (blau) oder die Zubehörstromversorgungsleitung (rot) an den Stromversorgungsanschluss des vorhandenen Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem Händler. Es kann nur eine Motorantenne mit Relaiskästchen angeschlossen werden. When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection Stromversorgung des Speichers Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. Do not connect the unit’s speaker leads to each other. Ce raccordement existe seulement pour les amplificateurs. Le raccordement à tout autre système peut endommager l’appareil. Questo collegamento è riservato esclusivamente agli amplificatori. Non collegare un tipo di sistema diverso onde evitare di causare danni all’apparecchio. Avertissement Si vous disposez d’une antenne électrique sans boîtier de relais, le branchement de cet appareil au moyen du cordon d’alimentation fourni 3 risque d’endommager l’antenne. Remarques sur les câbles de commande et d’alimentation Le câble de commande d’antenne électrique (bleu) fournit du courant continu de +12 V lorsque vous mettez le tuner sous tension ou lorsque vous activez la fonction AF (fréquence alternative) ou TA (informations de circulation). Lorsque votre voiture est équipée d’une antenne FM/MW (PO)/LW (GO) intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne électrique (bleu) ou le câble d’alimentation des accessoires (rouge) à la borne d'alimentation de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre revendeur. Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Wenn die gelbe Stromversorgungsleitung angeschlossen ist, wird der Speicher stets (auch bei ausgeschalteter Zündung) mit Strom versorgt. Hinweise zum Lautsprecheranschluss Remarques sur le raccordement des haut-parleurs Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. A A AMP REMOTE IN di un amplificatore di potenza de puissance facultatif Lorsque le câble d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est en position d’arrêt. Schalten Sie das Gerät aus, bevor Sie die Lautsprecher anschließen. Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und 8 Ohm und ausreichender Belastbarkeit. Ansonsten können die Lautsprecher beschädigt werden. Verbinden Sie die Lautsprecheranschlüsse nicht mit dem Wagenchassis und verbinden Sie auch nicht die Anschlüsse des rechten mit denen des linken Lautsprechers. Verbinden Sie die Masseleitung dieses Geräts nicht mit dem negativen (–) Lautsprecheranschluss. Versuchen Sie nicht, Lautsprecher parallel anzuschließen. An die Lautsprecheranschlüsse dieses Geräts dürfen nur Passivlautsprecher angeschlossen werden. Schließen Sie keine Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an, da das Gerät sonst beschädigt werden könnte. Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn am Ende eine gemeinsame negative (–) Leitung für den rechten und den linken Lautsprecher verwendet wird. Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander. Hinweis zum Anschließen Wenn Lautsprecher und Verstärker nicht richtig angeschlossen sind, erscheint „FAILURE“ im Display. Vergewissern Sie sich in diesem Fall, dass Lautsprecher und Verstärker richtig angeschlossen sind. Schema di collegamento A Vers la prise AMP REMOTE IN d’un amplificateur Dieser Anschluss ist ausschließlich für Verstärker gedacht. Schließen Sie nichts anderes daran an. Andernfalls kann das Gerät beschädigt werden. This connection is only for amplifiers. Connecting any other system may damage the unit. Warning Schéma de raccordement Anschlussdiagramm Connection diagram A To AMP REMOTE IN of an optional power Gray Grau Gris Grigio Grijs Avant de raccorder les haut-parleurs, mettre l’appareil hors tension. Utiliser des haut-parleurs ayant une impédance de 4 à 8 ohms et une capacité adéquate sous peine de les endommager. Ne pas raccorder les bornes du système de haut-parleurs au châssis de la voiture et ne pas connecter les bornes des haut-parleurs droit à celles des haut-parleurs gauche. Ne pas raccorder le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur. Ne pas tenter de raccorder les haut-parleurs en parallèle. Connecter uniquement des haut -parleurs passifs. La connexion de haut -parleurs actifs (avec des amplificateurs intégrés) aux bornes des haut -parleurs pourrait endommager l’appareil. Pour éviter tout problème de fonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés (–) installés dans votre voiture si l’appareil dispose d’un câble négatif commun pour les haut-parleurs droit et gauche. Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil. Remarque sur le raccordement Si les haut-parleurs et l’amplificateur ne sont pas raccordés correctement, le message «FAILURE» s’affiche. Dans ce cas, assurez-vous que les haut-parleurs et l’amplificateur sont raccordés correctement. White Weiß Blanc Bianco Wit Green Grün Vert Verde Groen + Speaker, Front, Left Lautsprecher vorne links Haut-parleur, avant, gauche Diffusore, anteriore, sinistro Luidspreker, voor, links – Speaker, Front, Left Lautsprecher vorne links Haut-parleur, avant, gauche Diffusore, anteriore, sinistro Luidspreker, voor, links + Speaker, Rear, Left Lautsprecher hinten links Haut-parleur, arrière, gauche Diffusore, posteriore, sinistro Luidspreker, achter, links – Speaker, Rear, Left Lautsprecher hinten links Haut-parleur, arrière, gauche Diffusore, posteriore, sinistro Luidspreker, achter, links Negative polarity positions 2, 4, 6, and 8 have striped leads. An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern. Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés. Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati. De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels. Positions 1, 2, 3, and 6 do not have pins. An Position 1, 2, 3 und 6 befinden sich keine Stifte. Les positions 1, 2, 3 et 6 ne comportent pas de broches. Le posizioni 1, 2, 3 e 6 non hanno piedini. De posities 1, 2, 3 en 6 hebben geen pins. Indien uw auto is uitgerust met een antenne van het type ISO (International Organization for Standardization), moet u die aansluiten met behulp van de bijgeleverde adapter 2. Sluit eerst de auto-antenne aan op de bijgeleverde adapter en vervolgens de antennestekker op het hoofdtoestel. *2 Tulpstekkersnoer (niet bijgeleverd). *3 AUDIO OUT kan worden ingesteld op SUB of REAR. Raadpleeg de gebruiksaanwijzing voor meer informatie. *4 Er is mogelijk een afzonderlijke adapter vereist. 2 Max. supply current 0.3 A max. Versorgungsstrom 0,3 A Courant d’alimentation maximum 0,3 A Alimentazione massima fornita 0,3 A Max. voedingsstroom 0,3 A AMP REM *1 Opmerking bij de antenne-aansluiting REAR / SUB AUDIO OUT * 3 *2 *1 from car antenna (aerial) von Autoantenne de l’antenne de la voiture dall’antenna dell’auto van een auto-antenne *1 Remarque sur le raccordement de l’antenne *1 Note for the antenna (aerial) connecting opzionale Avvertenza Quando si collega l’apparecchio con il cavo di alimentazione in dotazione 3, si potrebbe danneggiare l’antenna elettrica se questa non dispone di scatola a relè. Note sui cavi di controllo e di alimentazione Il cavo (blu) di controllo dell’antenna elettrica fornisce alimentazione pari a +12 V CC quando si attiva il sintonizzatore oppure la funzione TA (notiziario sul traffico) o AF (frequenza alternativa). Se l’automobile è dotata di antenna FM/MW/LW incorporata nel vetro posteriore/laterale, collegare il cavo (blu) di controllo dell’antenna elettrica o il cavo (rosso) di ingresso dell’alimentazione accessoria al terminale di alimentazione del preamplificatore dell’antenna esistente. Per ulteriori informazioni, consultare il proprio fornitore. Non è possibile usare un’antenna elettrica senza scatola a relè con questo apparecchio. Collegamento per la conservazione della memoria Quando il cavo di ingresso alimentazione giallo è collegato, viene sempre fornita alimentazione al circuito di memoria anche quando l’interruttore di accensione è spento. Note sul collegamento dei diffusori Prima di collegare i diffusori spegnere l’apparecchio. Usare diffusori di impedenza compresa tra 4 e 8 ohm e con capacità di potenza adeguata, altrimenti i diffusori potrebbero venire danneggiati. Non collegare i terminali del sistema diffusori al telaio dell’auto e non collegare i terminali del diffusore destro a quelli del diffusore sinistro. Non collegare il cavo di terra di questo apparecchio al terminale negativo (–) del diffusore. Non collegare i diffusori in parallelo. Assicurarsi di collegare soltanto diffusori passivi, poiché il collegamento di diffusori attivi, dotati di amplificatori incorporati, ai terminali dei diffusori potrebbe danneggiare l’apparecchio. Per evitare problemi di funzionamento, non utilizzare i cavi dei diffusori incorporati installati nell’automobile se l’apparecchio condivide un cavo comune negativo (–) per i diffusori destro e sinistro. Non collegare fra loro i cavi dei diffusori dell’apparecchio. Aansluitschema A Naar AMP REMOTE IN van een optionele eindversterker Deze aansluiting is alleen bedoeld voor versterkers. Door een ander systeem aan te sluiten kan het apparaat worden beschadigd. Waarschuwing Indien u een elektrische antenne hebt zonder relaiskast, kan het aansluiten van dit apparaat met de bijgeleverde voedingskabel 3 de antenne beschadigen. Opmerkingen over de bedienings- en voedingskabels Instandhouden van het geheugen Zolang de gele voedingskabel is aangesloten, blijft de stroomvoorziening van het geheugen intact, ook wanneer het contact van de auto wordt uitgeschakeld. Opmerkingen betreffende het aansluiten van de luidsprekers Nota sui collegamenti Se l’amplificatore e il diffusore non sono collegati correttamente, “FAILURE” viene visualizzato nel display. In tal caso, accertarsi che l’amplificatore e il diffusore siano collegati correttamente. De bedieningskabel voor de elektrische antenne (blauw) levert +12 V gelijkstroom wanneer u de tuner inschakelt of de functie AF (Alternative Frequency) of TA (Traffic Announcement) activeert. Wanneer uw auto is uitgerust met een FM/MW/LW-antenne in de achterruit/zijruit, moet u de bedieningskabel voor de elektrische antenne (blauw) of de hulpvoedingskabel (rood) aansluiten op de voedingsingang van de bestaande antenneversterker. Raadpleeg uw dealer voor meer details. Met dit apparaat is het niet mogelijk een elektrische antenne zonder relaiskast te gebruiken. Zorg dat het apparaat is uitgeschakeld, alvorens de luidsprekers aan te sluiten. Gebruik luidsprekers met een impedantie van 4 tot 8 ohm en let op dat die het vermogen van de versterker kunnen verwerken. Als u dit niet doet, kunnen de luidsprekers ernstig beschadigd raken. Verbind in geen geval de aansluitingen van de luidsprekers met het chassis van de auto en sluit de aansluitingen van de rechter- en linkerluidspreker niet op elkaar aan. Verbind de aarddraad van dit apparaat niet met de negatieve (–) aansluiting van de luidspreker. Probeer nooit de luidsprekers parallel aan te sluiten. Sluit geen actieve luidsprekers (met ingebouwde versterkers) aan op de luidsprekeraansluiting van dit apparaat. Dit zal leiden tot beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend luidsprekers zonder ingebouwde versterker aan. Om defecten te vermijden mag u de bestaande luidsprekerbedrading in uw auto niet gebruiken wanneer er een gemeenschappelijke negatieve (–) draad is voor de rechter- en linkerluidsprekers. Verbind de luidsprekerdraden niet met elkaar. Opmerking over aansluiten Als de luidspreker en versterker niet correct zijn aangesloten, wordt "FAILURE" in het display weergegeven. In dit geval moet u zorgen dat de luidspreker en versterker correct zijn aangesloten. 9 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.1 • CDX-GT40U: Russian model/GT42UE/GT47UE REAR / SUB AUDIO OUT * 3 *2 * ɉɪɢɦɟɱɚɧɢɟɨɩɨɞɫɨɟɞɢɧɟɧɢɢɚɧɬɟɧɧɵ * ɉɪɢɦɿɬɤɚɞɨɩɿɞɤɥɸɱɟɧɧɹɪɚɞɿɨɚɧɬɟɧɢ ȿɫɥɢɚɧɬɟɧɧɚɜȼɚɲɟɦɚɜɬɨɦɨɛɢɥɟ ɨɬɧɨɫɢɬɫɹɤɬɢɩɭɭɬɜɟɪɠɞɟɧɧɨɦɭ,S2 Ɇɟɠɞɭɧɚɪɨɞɧɨɣɨɪɝɚɧɢɡɚɰɢɟɣɩɨ ɫɬɚɧɞɚɪɬɢɡɚɰɢɢ ɢɫɩɨɥɶɡɭɣɬɟɞɥɹɟɟ ɩɨɞɫɨɟɞɢɧɟɧɢɹɩɪɢɥɚɝɚɟɦɵɣɩɟɪɟɯɨɞɧɢɤ2 ɋɧɚɱɚɥɚɩɨɞɫɨɟɞɢɧɢɬɟɚɜɬɨɦɨɛɢɥɶɧɭɸ ɚɧɬɟɧɧɭɤɩɪɢɥɚɝɚɟɦɨɦɭɩɟɪɟɯɨɞɧɢɤɭɚ ɡɚɬɟɦɤɚɧɬɟɧɧɨɦɭɝɧɟɡɞɭɚɩɩɚɪɚɬɚ * ɄɚɛɟɥɶɫɪɚɡɴɟɦɚɦɢRC$ ɧɟɜɯɨɞɢɬɜ ɤɨɦɩɥɟɤɬ * ȾɥɹA8',2287ɦɨɠɧɨɜɵɛSDɬɶɩɨɥɨɠHɧɢH S8%ɢɥɢR(ARȾɥɹɩɨɥ\ɱHɧɢɹ ɞɨɩɨɥɧɢɬHɥɶɧɨɣɢɧɮɨSɦDɰɢɢFɦ ɩSɢɥDɝDHɦɵHɢɧFɬS\ɤɰɢɢɩɨɷɤFɩɥ\DɬDɰɢɢ * Ɇɨɠɟɬɩɨɬɪɟɛɨɜɚɬɶɫɹɨɬɞɟɥɶɧɵɣ ɚɞɚɩɬɟɪ əɤɳɨɚɜɬɨɦɨɛɿɥɶɧɚɪɚɞɿɨɚɧɬɟɧɚɧɚɥɟɠɢɬɶ ɞɨɬɢɩɭ,S2 Ɇɿɠɧɚɪɨɞɧɚɨɪɝɚɧɿɡɚɰɿɹɡɿ ɫɬɚɧɞɚɪɬɢɡɚɰɿʀ ɞɥɹʀʀɩɿɞɤɥɸɱɟɧɧɹ ɜɢɤɨɪɢɫɬɨɜɭɣɬɟɚɞɚɩɬɟɪ 2 ɋɩɨɱɚɬɤɭ ɩɿɞɤɥɸɱɿɬɶɚɜɬɨɦɨɛɿɥɶɧɭɚɧɬɟɧɭɞɨ ɚɞɚɩɬɟɪɚɡɤɨɦɩɥɟɤɬɭɚɩɨɬɿɦɩɿɞɤɥɸɱɿɬɶ ʀʀɞɨɝɧɿɡɞɚɚɧɬɟɧɢɜɝɨɥɨɜɧɨɦɭɩɪɢɫɬɪɨʀ * ɒɧɭɪRCAɡɤɨɧɬɚɤɬɧɢɦɢɲɬɢɪɤɚɦɢ ɧɟ ɧɚɞɚɽɬɶɫɹɜɤɨɦɩɥɟɤɬɿ * A8',2287ɦɨɠɧɚɩɟɪɟɤɥɸɱɢɬɢɧɚS8%ɚɛɨ R(ARȾɥɹɨɬɪɢɦɚɧɧɹɞɨɤɥɚɞɧɿɲɨʀ ɿɧɮɨɪɦɚɰɿʀɞɢɜȱɧɫɬɪɭɤɰɿɸɡɟɤɫɩɥɭɚɬɚɰɿʀ * Ɇɨɠɟɡɧɚɞɨɛɢɬɢɫɹɨɤɪɟɦɢɣɚɞɚɩɬɟɪ 2 *1 ɨɬɚɜɬɨɦɨɛɢɥɶɧɨɣɚɧɬɟɧɧɵ ɜɿɞɚɜɬɨɦɨɛɿɥɶɧɨʀɪɚɞɿɨɚɧɬɟɧɢ REMOTE IN * 4 ɉɪɟɞɨɯɪɚɧɢɬɟɥɶ Ⱥ Ɂɚɩɨɛɿɠɧɢɤ (10 A ɋɫɢɧɟɛɟɥɵɦɢɩɨɥɨɫɤɚɦɢ ɍɫɢɧɶɨɛɿɥɭɫɦɭɠɤɭ AMP REM ɆɚɤɫɫɢɥɚɬɨɤɚȺ Ɇɚɤɫɫɢɥɚɫɬɪɭɦɭ±$ 3 ɨɬɪɚɡɴɟɦɚɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɟɣ ɚɜɬɨɦɨɛɢɥɹ ɜɿɞɪɨɡ¶ɽɦɭɞɢɧɚɦɿɤɚɚɜɬɨɦɨɛɿɥɹ 1 2 3 4 Ɏɢɨɥɟɬɨɜɵɣ Ɏɿɨɥɟɬɨɜɢɣ ɋɟɪɵɣ ɋɿɪɢɣ + Ƚɪɨɦɤɨɝɨɜɨɪɢɬɟɥɶɡɚɞɧɢɣɩɪɚɜɵɣ Ⱦɢɧɚɦɿɤɡɚɞɧɿɣɩɪɚɜɢɣ 5 ± Ƚɪɨɦɤɨɝɨɜɨɪɢɬɟɥɶɡɚɞɧɢɣɩɪɚɜɵɣ Ⱦɢɧɚɦɿɤɡɚɞɧɿɣɩɪɚɜɢɣ 6 + ± Ȼɟɥɵɣ Ȼɿɥɢɣ Ⱦɢɧɚɦɿɤɩɟɪɟɞɧɿɣɩɪɚɜɢɣ Ƚɪɨɦɤɨɝɨɜɨɪɢɬɟɥɶɩɟɪɟɞɧɢɣɥɟɜɵɣ Ⱦɢɧɚɦɿɤɩɟɪɟɞɧɿɣɥɿɜɢɣ ± Ƚɪɨɦɤɨɝɨɜɨɪɢɬɟɥɶɩɟɪɟɞɧɢɣɥɟɜɵɣ Ⱦɢɧɚɦɿɤɩɟɪɟɞɧɿɣɥɿɜɢɣ + Ƚɪɨɦɤɨɝɨɜɨɪɢɬɟɥɶɡɚɞɧɢɣɥɟɜɵɣ Ⱦɢɧɚɦɿɤɡɚɞɧɿɣɥɿɜɢɣ ± Ƚɪɨɦɤɨɝɨɜɨɪɢɬɟɥɶɡɚɞɧɢɣɥɟɜɵɣ Ⱦɢɧɚɦɿɤɡɚɞɧɿɣɥɿɜɢɣ 7 Ʉɪɚɫɧɵɣ ɑɟɪɜɨɧɢɣ ɢɦɩɭɥɶɫɧɵɣɢɫɬɨɱɧɢɤɩɢɬɚɧɢɹ ɿɦɩɭɥɶɫɧɟɩɨɫɬɚɱɚɧɧɹɠɢɜɥɟɧɧɹ 8 ɑɟɪɧɵɣ ɑɨɪɧɢɣ ɡɟɦɥɹ ɡɚɡɟɦɥɟɧɧɹ Ƚɪɨɦɤɨɝɨɜɨɪɢɬɟɥɶɩɟɪɟɞɧɢɣɩɪɚɜɵɣ 7 Ⱦɢɧɚɦɿɤɩɟɪɟɞɧɿɣɩɪɚɜɢɣ Ƚɪɨɦɤɨɝɨɜɨɪɢɬɟɥɶɩɟɪɟɞɧɢɣɩɪɚɜɵɣ + Ɂɟɥɟɧɵɣ Ɂɟɥɟɧɢɣ 8 ɉɨɡɢɰɢɢɨɬɪɢɰɚɬɟɥɶɧɨɣɩɨɥɹɪɧɨɫɬɢɢɢɦɟɸɬɩɪɨɜɨɞɚɫɩɨɥɨɫɤɚɦɢ ɉɪɨɜɨɞɤɚɞɨɩɨɡɢɰɿɣɿɡɜɿɞ¶ɽɦɧɨɸɩɨɥɹɪɧɿɫɬɸɿ±ɫɦɭɝɚɫɬɚ ɨɬɪɚɡɴɟɦɚɷɥɟɤɬɪɨɩɢɬɚɧɢɹ ɚɜɬɨɦɨɛɢɥɹ ɜɿɞɪɨɡ¶ɽɦɭɠɢɜɥɟɧɧɹɚɜɬɨɦɨɛɿɥɹ ɉɨɞSɨɛɧHHFɦɜSDɡɞHɥH “CxHɦDɩɨɞɤɥɸɱHɧɢɹ ɩɢɬDɧɢɹ”ɧDɨɛSDɬɧɨɣFɬɨSɨɧH Ⱦɥɹɨɬɪɢɦɚɧɧɹɞɟɬɚɥɶɧɨʀɿɧɮɨɪɦɚɰɿʀɞɢɜ©ɋɯɟɦɚ ɩɿɞɤɥɸɱɟɧɧɹɠɢɜɥɟɧɧɹªɧɚɡɜɨɪɨɬɧɿɣɫɬɨɪɨɧɿ 4 ɀɟɥɬɵɣ ɀɨɜɬɢɣ ɧɟɩɪɟɪɵɜɧɨɟɩɨɫɬɭɩɥɟɧɢɟɩɢɬɚɧɢɹ ɧɟɩɟɪɟɪɜɧɟɩɨɫɬɚɱɚɧɧɹɠɢɜɥɟɧɧɹ 5 ɋɢɧɢɣ ɋɢɧɿɣ ɭɩɪɚɜɥɟɧɢɟɚɧɬɟɧɧɨɣɫ ɷɥɟɤɬɪɢɱɟɫɤɢɦɩɪɢɜɨɞɨɦ ɤɟɪɭɜɚɧɧɹɚɧɬɟɧɨɸɡɟɥɟɤɬɪɨɩɪɢɜɨɞɨɦ ɉɨɡɢɰɢɢɢɧɟɢɦɟɸɬɤɨɧɬɚɤɬɧɵɯɲɬɵɪɶɤɨɜ ɉɨɡɢɰɿʀɬɚɧɟɦɚɸɬɶɤɨɧɬɚɤɬɧɢɯɲɬɢɪɤɿɜ ɋɯɟɦɚɩɿɞɤɥɸɱɟɧɧɹ ɋɯɟɦɚɩɨɞɫɨɟɞɢɧɟɧɢɹ A ɉɨɞɤɥɸɱHɧɢHɤɜ[ɨɞ\$035(0O7(,1 ɞɨɩɨɥɧɢɬHɥɶɧɨɝɨ\cɢɥɢɬHɥɹɦɨɳɧɨFɬɢ A Ⱦɥɹ$035(0O7(,1ɞɨɞɚɬɤɨɜɨɝɨɩɿɞɫɢɥɸɜɚɱɚ ɩɨɬɭɠɧɨɫɬɿ ɐɟɩɿɞɤɥɸɱɟɧɧɹɜɢɤɨɪɢɫɬɨɜɭɽɬɶɫɹɥɢɲɟɞɥɹɩɿɞɫɢɥɸɜɚɱɿɜ ɉɿɞɤɥɸɱɟɧɧɹɛɭɞɶɹɤɨʀɿɧɲɨʀɫɢɫɬɟɦɢɦɨɠɟɩɨɲɤɨɞɢɬɢ ɩɪɢɫɬɪɿɣ ɗɬɨɬɜDSɢDɧɬɩɨɞɤɥɸɱHɧɢɹɢFɩɨɥɶɡyHɬFɹɬɨɥɶɤɨɞɥɹ yFɢɥɢɬHɥHɣɉɨɞɤɥɸɱHɧɢHɥɸɛɨɣɞS\ɝɨɣFɢFɬHɦɵɦɨɠHɬ ɩSɢɜHFɬɢɤɩɨɜSHɠɞHɧɢɸɚɩɩɚɪɚɬɚ ɉɪɟɞɨɫɬɟɪɟɠɟɧɢɟ ɍɜɚɝɚ ȿɫɥɢȼɵɢɫɩɨɥɶɡɭɟɬɟɚɧɬɟɧɧɭɫɷɥɟɤɬɪɢɱɟɫɤɢɦ ɩɪɢɜɨɞɨɦɛɟɡɪɟɥɟɣɧɨɝɨɛɥɨɤɚɩɨɞɫɨɟɞɢɧɟɧɢɟɷɬɨɝɨ ɚɩɩɚɪɚɬɚɩɨɫɪɟɞɫɬɜɨɦɩɪɢɥɚɝɚɟɦɨɝɨɩɪɨɜɨɞɚ ɩɢɬɚɧɢɹ3ɦɨɠɟɬɩɪɢɜɟɫɬɢɤɩɨɜɪɟɠɞɟɧɢɸ ɚɧɬɟɧɧɵ əɤɳɨɚɧɬɟɧɚɡɟɥɟɤɬɪɨɩɪɢɜɨɞɨɦɧɟɦɚɽɪɟɥɟɣɧɨʀ ɫɬɿɣɤɢɩɿɞɤɥɸɱɟɧɧɹɰɶɨɝɨɩɪɢɫɬɪɨɸɡɚɞɨɩɨɦɨɝɨɸ ɤɚɛɟɥɸɠɢɜɥɟɧɧɹɡɤɨɦɩɥɟɤɬɭ3ɦɨɠɟɩɨɲɤɨɞɢɬɢ ɚɧɬɟɧɭ Ɉɩɪɨɜɨɞɚɯɭɩɪɚɜɥɟɧɢɹɢɩɢɬɚɧɢɹ ɉɪɢɜɤɥɸɱɟɧɢɢɬɸɧɟɪɚɚɬɚɤɠɟɢɫɩɨɥɶɡɨɜɚɧɢɢɮɭɧɤɰɢɢ$) (Ⱥɥɶɬɟɪɧɚɬɢɜɧɵɟɱɚɫɬɨɬɵ ɢɥɢT$ ɋɨɨɛɳɟɧɢɹɨɬɟɤɭɳɟɣ ɫɢɬɭɚɰɢɢɧɚɞɨɪɨɝɚɯ ɩɨɩɪɨɜɨɞɭɩɢɬɚɧɢɹɩɪɢɟɦɧɨɣɚɧɬɟɧɧɵ ɫɢɧɢɣ ɩɨɞɚɟɬɫɹȼɩɨɫɬɨɹɧɧɨɝɨɬɨɤɚ EFɥɢɧDɡDɞɧHɦɛɨɤɨɜɨɦFɬHɤɥHDɜɬɨɦɨɛɢɥɹyFɬDɧɨɜɥHɧD ɜFɬSɨHɧɧDɹDɧɬHɧɧDɞɢDɩDɡɨɧD)00:L:ɩɨɞFɨHɞɢɧɢɬH ɩSɨɜɨɞɭɩɪɚɜɥɟɧɢɹɚɧɬɟɧɧɨɣɫɷɥɟɤɬɪɢɱɟɫɤɢɦɩɪɢɜɨɞɨɦ (Fɢɧɢɣ ɢɥɢɩSɨɜɨɞɩɢɬDɧɢɹɚɩɩɚɪɚɬɚ ɤSDFɧɵɣ ɤɤɥHɦɦH ɩɢɬDɧɢɹF\ɳHFɬɜ\ɸɳHɝɨyFɢɥɢɬHɥɹDɧɬHɧɧɵɑɬɨɛɵ ɩɨɥ\ɱɢɬɶɞɨɩɨɥɧɢɬHɥɶɧɵHFɜHɞHɧɢɹɨɛSDɬɢɬHFɶɤFɜɨHɦ\ ɞɢɥHSy Ⱥɧɬɟɧɧɚɫɷɥɟɤɬɪɢɱɟɫɤɢɦɩɪɢɜɨɞɨɦɧɟɫɧɚɛɠɟɧɧɚɹɪɟɥɟɣɧɵɦ ɛɥɨɤɨɦɫɷɬɢɦɚɩɩɚɪɚɬɨɦɢɫɩɨɥɶɡɨɜɚɬɶɫɹɧɟɦɨɠɟɬ ɉɨɞɫɨɟɞɢɧɟɧɢɟɞɥɹɩɨɞɞɟɪɠɤɢɩɚɦɹɬɢ ɉɪɢɦɿɬɤɚɳɨɞɨɤɚɛɟɥɸɤɟɪɭɜɚɧɧɹɬɚɤɚɛɟɥɸɩɨɫɬɚɱɚɧɧɹ ɠɢɜɥɟɧɧɹ Ʉɚɛɟɥɶɤɟɪɭɜɚɧɧɹɚɧɬɟɧɨɸɡɟɥɟɤɬɪɨɩɪɢɜɨɞɨɦ ɫɢɧɿɣ ɩɨɫɬɚɱɚɽȼɩɨɫɬɿɣɧɨʀɧɚɩɪɭɝɢɡɚɜɜɿɦɤɧɟɧɧɹɬɸɧɟɪɚɚɛɨɩɿɞ ɱɚɫɚɤɬɢɜɚɰɿʀɮɭɧɤɰɿʀ$)($OtHUQDWLvH)UHTXHQF\ ɚɥɶɬɟɪɧɚɬɢɜɧɚ ɱɚɫɬɨɬɚ ɚɛɨT$(TUDIILF$QQRXQFHPHQW ɩɨɜɿɞɨɦɥɟɧɧɹɩɪɨ ɫɢɬɭɚɰɿɸɧɚɞɨɪɨɝɚɯ əɤɳɨɜɚɲɚɜɬɨɦɨɛɿɥɶɨɫɧɚɳɟɧɨɜɛɭɞɨɜɚɧɨɸɚɧɬɟɧɨɸ)00: L:ɧɚɡɚɞɧɶɨɦɭɛɨɤɨɜɨɦɭɫɤɥɿɩɿɞɤɥɸɱɿɬɶɤɚɛɟɥɶɤɟɪɭɜɚɧɧɹ ɚɧɬɟɧɨɸ ɫɢɧɿɣ ɚɛɨɞɨɞɚɬɤɨɜɢɣɤɚɛɟɥɶɩɿɞɤɥɸɱɟɧɧɹɠɢɜɥɟɧɧɹ ɱɟɪɜɨɧɢɣ ɞɨɪɨɡ¶ɽɦɭɠɢɜɥɟɧɧɹɧɚɹɜɧɨɝɨɚɧɬɟɧɧɨɝɨ ɩɿɞɫɢɥɸɜɚɱɚȾɥɹɨɬɪɢɦɚɧɧɹɞɟɬɚɥɶɧɨʀɿɧɮɨɪɦɚɰɿʀɡɜɟɪɧɿɬɶɫɹ ɞɨɫɜɨɝɨɞɢɥɟɪɚɡɩɪɨɞɚɠɭ Ⱥɧɬɟɧɭɡɟɥɟɤɬɪɨɩɪɢɜɨɞɨɦɛɟɡɪɟɥɟɣɧɨʀɫɬɿɣɤɢɧɟɦɨɠɧɚ ɜɢɤɨɪɢɫɬɨɜɭɜɚɬɢɡɰɢɦɩɪɢɫɬɪɨɽɦ ɉɿɞɤɥɸɱɟɧɧɹɡɚɩɚɦ¶ɹɬɨɜɭɜɚɥɶɧɨʀɫɢɫɬɟɦɢ Ʉɨɝɞɚɤɚɩɩɚɪɚɬɭɩɨɞɫɨɟɞɢɧɟɧɠɟɥɬɵɣɷɥɟɤɬɪɢɱɟɫɤɢɣɩɪɨɜɨɞ ɛɥɨɤɩɚɦɹɬɢɛɭɞɟɬɩɨɫɬɨɹɧɧɨɩɨɥɭɱɚɬɶɩɢɬɚɧɢɟɞɚɠɟɩɪɢ ɜɵɤɥɸɱɟɧɧɨɦɡɚɠɢɝɚɧɢɢ əɤɳɨɩɿɞɤɥɸɱɟɧɨɠɨɜɬɢɣɤɚɛɟɥɶɩɨɫɬɚɱɚɧɧɹɠɢɜɥɟɧɧɹɠɢɜɥɟɧɧɹ ɡɚɜɠɞɢɩɨɫɬɚɱɚɬɢɦɟɬɶɫɹɞɨɡɚɩɚɦ¶ɹɬɨɜɭɜɚɥɶɧɨʀɫɯɟɦɢɧɚɜɿɬɶ ɡɚɜɢɦɤɧɟɧɨɝɨɡɚɩɚɥɟɧɧɹ ɉɪɢɦɟɱɚɧɢɹɨɬɧɨɫɢɬɟɥɶɧɨɩɨɞɫɨɟɞɢɧɟɧɢɹ ɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɟɣ ɉɪɢɦɿɬɤɚɳɨɞɨɩɿɞɤɥɸɱɟɧɧɹɞɢɧɚɦɿɤɚ ɉɪɟɠɞɟɱɟɦɩɨɞɫɨɟɞɢɧɹɬɶɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɢɜɵɤɥɸɱɢɬɟ ɚɩɩɚɪɚɬ ɂɫɩɨɥɶɡɭɣɬɟɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɢɫɩɨɥɧɵɦɫɨɩɪɨɬɢɜɥɟɧɢɟɦ Ɉɦɨɛɥɚɞɚɸɳɢɟɫɩɨɫɨɛɧɨɫɬɶɸɩɪɢɧɢɦɚɬɶɞɨɫɬɚɬɨɱɧɨ ɦɨɳɧɵɣɫɢɝɧɚɥȼɩɪɨɬɢɜɧɨɦɫɥɭɱɚɟɨɧɢɦɨɝɭɬɛɵɬɶ ɩɨɜɪɟɠɞɟɧɵ ɇɟɩɨɞɫɨɟɞɢɧɹɣɬɟɤɨɧɬɚɤɬɧɵɟɝɧɟɡɞɚɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɟɣɤ ɲɚɫɫɢɚɜɬɨɦɨɛɢɥɹɢɧɟɫɨɟɞɢɧɹɣɬɟɝɧɟɡɞɚɩɪɚɜɨɝɨ ɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɹɫɝɧɟɡɞɚɦɢɥɟɜɨɝɨ +HɩɨɞɤɥɸɱDɣɬHɩSɨɜɨɞɡDɡHɦɥHɧɢɹɚɩɩɚɪɚɬɚɤ ɨɬSɢɰDɬHɥɶɧɨɦ\ ± ɤɨɧɬDɤɬ\ɝSɨɦɤɨɝɨɜɨSɢɬHɥɹ ɇɟɩɵɬɚɣɬɟɫɶɩɨɞɫɨɟɞɢɧɢɬɶɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɢɩɚɪɚɥɥɟɥɶɧɨ ɉɨɞɫɨɟɞɢɧɹɬɶɦɨɠɧɨɬɨɥɶɤɨɩɚɫɫɢɜɧɵɟɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɢ ɉɨɞɫɨɟɞɢɧɟɧɢɟɚɤɬɢɜɧɵɯɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɟɣ ɫɨɜɫɬɪɨɟɧɧɵɦ ɭɫɢɥɢɬɟɥɟɦ ɤɝɧɟɡɞɚɦɞɥɹɝɪɨɦɤɨɝɨɜɨɪɢɬɟɥɟɣɦɨɠɟɬ ɩɪɢɜɟɫɬɢɤɩɨɜɪɟɠɞɟɧɢɸɚɩɩɚɪɚɬɚ %ɨɢɡɛHɠDɧɢHɧHɩSDɜɢɥɶɧɨɣSDɛɨɬɵɚɩɩɚɪɚɬɚɧHɢFɩɨɥɶɡ\ɣɬH ɜFɬSɨHɧɧɵHɜDɜɬɨɦɨɛɢɥɶɩSɨɜɨɞDɝSɨɦɤɨɝɨɜɨSɢɬHɥHɣHFɥɢ ɢɫɩɨɥɶɡɭɟɬɫɹɨɛɳɢɣɨɬSɢɰDɬHɥɶɧɵɣɩSɨɜɨɞ ± ɞɥɹɩSDɜɨɝɨɢ ɥHɜɨɝɨɝSɨɦɤɨɝɨɜɨSɢɬHɥHɣ +HɩɨɞɫɨɟɞɢɧɹɣɬɟɞɪɭɝɤɞɪɭɝɭɩSɨɜɨɞDɝSɨɦɨɤɨɝɨɜɨSɢɬHɥHɣ ɚɩɩɚɪɚɬɚ ɉSɢɦHɱDɧɢHɨɬɧɨFɢɬHɥɶɧɨɩɨɞFɨHɞɢɧHɧɢɹ EFɥɢɝSɨɦɤɨɝɨɜɨSɢɬHɥɶɢyFɢɥɢɬHɥɶɩɨɞFɨHɞɢɧHɧɵɧHɩSDɜɢɥɶɧɨ ɧDɞɢFɩɥHHɨɬɨɛSDɡɢɬFɹɧDɞɩɢFɶ³)$,LURE´%ɷɬɨɦFɥ\ɱDH ɩSɨɜHSɶɬHɩSDɜɢɥɶɧɨFɬɶɩɨɞFɨHɞɢɧHɧɢɹɝSɨɦɤɨɝɨɜɨSɢɬHɥɹɢ yFɢɥɢɬHɥɹ 10 ɉɟɪɟɞɩɿɞɤɥɸɱɟɧɧɹɦɞɢɧɚɦɿɤɿɜɜɢɦɤɧɿɬɶɩɪɢɫɬɪɿɣ ȼɢɤɨɪɢɫɬɨɜɭɣɬɟɞɢɧɚɦɿɤɢɡɩɨɜɧɢɦɨɩɨɪɨɦɜɿɞɞɨɈɦɿɡ ɜɿɞɩɨɜɿɞɧɨɸɩɪɢɩɭɫɬɢɦɨɸɜɯɿɞɧɨɸɩɨɬɭɠɧɿɫɬɸɳɨɛɭɧɢɤɧɭɬɢ ʀɯɩɨɲɤɨɞɠɟɧɧɹ ɇɟɩɿɞɤɥɸɱɚɣɬɟɪɨɡ¶ɽɦɢɞɢɧɚɦɿɤɿɜɞɨɤɨɪɩɭɫɭɚɜɬɨɦɨɛɿɥɹɿɧɟ ɡ¶ɽɞɧɭɣɬɟɪɨɡ¶ɽɦɢɩɪɚɜɨɝɨɿɥɿɜɨɝɨɞɢɧɚɦɿɤɚ ɇɟɩɿɞɤɥɸɱɚɣɬɟɡɚɡɟɦɥɟɧɢɣɤɚɛɟɥɶɰɶɨɝɨɩɪɢɫɬɪɨɸɞɨ ɜɿɞ¶ɽɦɧɨɝɨ ± ɪɨɡ¶ɽɦɭɞɢɧɚɦɿɤɚ ɇɟɧɚɦɚɝɚɣɬɟɫɹɩɿɞɤɥɸɱɢɬɢɞɢɧɚɦɿɤɢɩɚɪɚɥɟɥɶɧɨ ɉɿɞɤɥɸɱɚɣɬɟɥɢɲɟɩɚɫɢɜɧɿɞɢɧɚɦɿɤɢɉɿɞɤɥɸɱɟɧɧɹɚɤɬɢɜɧɢɯ ɞɢɧɚɦɿɤɿɜ ɿɡɜɛɭɞɨɜɚɧɢɦɩɿɞɫɢɥɸɜɚɱɟɦ ɞɨɪɨɡ¶ɽɦɿɜɞɢɧɚɦɿɤɿɜ ɦɨɠɟɩɨɲɤɨɞɢɬɢɩɪɢɫɬɪɿɣ ɓɨɛɭɧɢɤɧɭɬɢɧɟɫɩɪɚɜɧɨʀɪɨɛɨɬɢɩɪɢɫɬɪɨɸɧɟ ɜɢɤɨɪɢɫɬɨɜɭɣɬɟɜɛɭɞɨɜɚɧɢɣɤɚɛɟɥɶɞɢɧɚɦɿɤɚɜɫɬɚɧɨɜɥɟɧɢɣɜ ɚɜɬɨɦɨɛɿɥɿɹɤɳɨɩɪɢɫɬɪɿɣɜɢɤɨɪɢɫɬɨɜɭɽɫɩɿɥɶɧɨɧɟɝɚɬɢɜɧɢɣ ± ɤɚɛɟɥɶɞɥɹɩɪɚɜɨɝɨɬɚɥɿɜɨɝɨɞɢɧɚɦɿɤɿɜ ɇɟɩɿɞɤɥɸɱɚɣɬɟɤɚɛɟɥɿɞɢɧɚɦɿɤɚɩɪɢɫɬɪɨɸɨɞɢɧɞɨɨɞɧɨɝɨ ɉɪɢɦɿɬɤɚɳɨɞɨɩɿɞɤɥɸɱɟɧɧɹ əɤɳɨɞɢɧɚɦɿɤɿɩɿɞɫɢɥɸɜɚɱɧɟɩɿɞɤɥɸɱɟɧɨɧɚɥɟɠɧɢɦɱɢɧɨɦɧɚ ɞɢɫɩɥɟʀɜɿɞɨɛɪɚɡɢɬɶɫɹ©)$,L85(ª ɩɨɦɢɥɤɚ ɍɬɚɤɨɦɭɜɢɩɚɞɤɭ ɩɟɪɟɤɨɧɚɣɬɟɫɹɳɨɞɢɧɚɦɿɤɿɩɿɞɫɢɥɸɜɚɱɩɿɞɤɥɸɱɟɧɨɧɚɥɟɠɧɢɦ ɱɢɧɨɦ CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.2 • CDX-GT44U: Indian model/GT45U: E, Saudi Arabia, Mexican, Korean model *1 Speaker impedance ± oKms î *2 RCA pin cord (not supplied). *3 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. *1 Impedancia de los altavoces de a î *2 Cable con terminales RCA (no suministrado). *3 AUDIO OUT (salida de audio) puede cambiarse a SUB o REAR. Para obtener información, consulte el manual de instrucciones suministrado. *4 Separate adaptor may be required. *4 Puede requerirse un adaptador independiente. *2 REAR / SUB AUDIO OUT * 3 REMOTE IN * 4 Fuse (10 A) Fusible (10 A) from car antenna (aerial) desde la antena del automóvil Blue/white striped Con rayas azules y blancas REM OUT Max. supply current 0.4 A Corriente máx. de alimentación de 0,4 A 2 White Blanco Left Izquierdo White/black striped Con rayas blancas y negras Gray Gris Right Derecho Black Negro Gray/black striped Con rayas grises y negras *1 Green Verde Left Izquierdo Red Rojo ACC Green/black striped Con rayas verdes y negras Purple Morado Right Derecho Yellow Amarillo BATTERY Purple/black striped Con rayas moradas y negras Connection diagram Diagrama de conexión 1 To a metal surface of the car 1 A una superficie metálica del automóvil 2 To the power antenna (aerial) control lead or 2 Al cable de control de la antena motorizada o al First connect the black ground (earth) lead, then connect the yellow, and red power supply leads. power supply lead of antenna (aerial) booster Conecte primero el cable de conexión a masa negro, y después los cables amarillo y rojo de fuente de alimentación. cable de fuente de alimentación del amplificador de señal de la antena Notes It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). When your car has a built-in FM/AM antenna (aerial) in the rear/ side glass, see “Notes on the control and power supply leads.” Notas To AMP REMOTE IN of an optional power amplifier A AMP REMOTE IN de un amplificador de potencia opcional This connection is only for amplifiers. Connecting any other system may damage the unit. 3 To the +12 V power terminal which is energized in the accessory position of the ignition key switch Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad. 3 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de encendido Notes If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. When your car has a built-in FM/AM antenna (aerial) in the rear/ side glass, see “Notes on the control and power supply leads.” Notas 4 To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first. REM OUT lead (blue/white striped) supplies +12 V DC when you turn on the unit. When your car has built-in FM/AM antenna (aerial) in the rear/side glass, connect REM OUT lead (blue/white striped) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. A power antenna (aerial) without a relay box cannot be used with this unit. energía sin interrupción Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. Notas sobre los cables de control y de fuente de alimentación Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. Si el automóvil tiene una antena de FM/AM incorporada en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. 4 Al terminal de alimentación de +12 V que recibe Notes on the control and power supply leads Si no se dispone de antena motorizada ni de amplificador de señal de la antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. Si el automóvil tiene una antena de FM/AM incorporada en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. El cable REM OUT (rayado azul y blanco) suministra cc +12 V al encender la unidad. Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero o lateral, conecte el cable REM OUT (rayado azul y blanco) o el cable de fuente de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de señal de la antena existente. Para obtener más detalles, consulte a su distribuidor. Con esta unidad no es posible utilizar una antena motorizada sin caja de relé. Conexión para protección de la memoria Si conecta el cable de fuente de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague el interruptor de encendido. Notas sobre la conexión de los altavoces Antes de conectar los altavoces, desconecte la alimentación de la Utilice altavoces con una impHGDQFLDGHDcon la capacidad de potencia adecuada para evitar que se dañen. No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. No conecte el cable de conexión a masa de esta unidad al terminal negativo (–) del altavoz. No intente conectar los altavoces en paralelo. Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. Para evitar fallas de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si la unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo. No conecte los cables de altavoz de la unidad entre sí. unidad. Nota sobre la conexión Si el altavoz y el amplificador no están conectados correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de ambos dispositivos. 11 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE • CDX-GT45U: Argentina model 1 2 * 3 2 REAR / SUB AUDIO OUT* 3 4 5 8 6 7 * 1 from car antenna (aerial) desde la antena del automóvil REMOTE IN * 4 Fuse (10 A) Fusible (10 A) 2 Blue/white striped Con rayas azules y blancas AMP REM Max. supply current 0.3 A Corriente máx. de alimentación de 0,3 A 8 Purple Morado Gray Gris White Blanco Green Verde + Speaker, Rear, Right Altavoz, posterior, derecho – Speaker, Rear, Right Altavoz, posterior, derecho + Speaker, Front, Right Altavoz, frontal, derecho – Speaker, Front, Right Altavoz, frontal, derecho + Speaker, Front, Left Altavoz, frontal, izquierdo – Speaker, Front, Left Altavoz, frontal, izquierdo + Speaker, Rear, Left Altavoz, posterior, izquierdo – Speaker, Rear, Left Altavoz, posterior, izquierdo Negative polarity positions 2, 4, 6, and 8 have striped leads. Los cables de las posiciones de polaridad negativa 2, 4, 6 y 8 son rayados. from the car’s speaker connector desde un conector de altavoces del automóvil * 1 Note for the antenna (aerial) connecting If your car antenna (aerial) is an ISO (International Organisation for Standardisation) type, use the supplied adaptor 8 to connect it. First connect the car antenna (aerial) to the supplied adaptor, then connect it to the antenna (aerial) jack of the master unit. 2 * RCA pin cord (not supplied) * 3 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. * 4 Separate adaptor may be required. * 1 Nota sobre la conexión de la antena Si la antena del automóvil es del tipo ISO (International Organization for Standardization), emplee el adaptador suministrado 8 para conectarla. En primer lugar, conecte la antena del automóvil al adaptador suministrado y, a continuación, a la toma de antena de la unidad principal. 2 * Cable con terminales RCA (no suministrado) * 3 AUDIO OUT (salida de audio) puede cambiarse a SUB o REAR. Para obtener información, consulte el manual de instrucciones suministrado. * 4 Puede requerirse un adaptador independiente. amplifier See “Power connection diagram” on the reverse side for details. 4 Yellow Amarillo continuous power supply fuente de alimentación continua Para obtener más información, consulte el “Diagrama de conexión de la alimentación” que encontrará al dorso. 5 Blue Azul power antenna (aerial) control control de la antena motorizada 7 Red Rojo switched power supply fuente de alimentación conmutada 8 Black Negro Positions 1, 2, 3 and 6 do not have pins. Las posiciones 1, 2, 3 y 6 no tienen pines. Diagrama de conexión Connection diagram A To AMP REMOTE IN of an optional power from the car’s power connector desde un conector de alimentación del automóvil A A AMP REMOTE IN de un amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad. This connection is only for amplifiers. Connecting any other system may damage the unit. Warning Advertencia If you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power connecting lead 2 may damage the antenna (aerial). Si la antena motorizada no dispone de caja de relé, es posible que la conexión de esta unidad mediante el cable de conexión de alimentación suministrado 2 provoque daños en la antena. Notes on the control and power supply leads The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. When your car has built-in FM/AM antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. A power antenna (aerial) without a relay box cannot be used with this unit. Notas sobre los cables de control y de fuente de alimentación El cable de control de la antena motorizada (azul) suministrará cc de + 12 V cuando conecte la alimentación del sintonizador. Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de fuente de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de señal de la antena existente. Para obtener más información, consulte a su distribuidor. Con esta unidad no es posible utilizar una antena motorizada sin caja de relé. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Conexión para protección de la memoria Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly. Si conecta el cable de fuente de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague el interruptor de encendido. Notas sobre la conexión de los altavoces Antes de conectar los altavoces, desconecte la alimentación de la unidad. Utilice altavoces con una impedancia de 4 a 8 con la capacidad de potencia adecuada para evitar que se dañen. No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. No conecte el cable de conexión a masa de esta unidad al terminal negativo (–) del altavoz. No intente conectar los altavoces en paralelo. Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. Para evitar fallas de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si la unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo. No conecte los cables de altavoz de la unidad entre sí. Nota sobre la conexión Si el altavoz y el amplificador no están conectados correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de ambos dispositivos. 12 earth masa CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. SET 3-1. SUB PANEL ASSY (Page 13) 3-2. CD MECHANISM BLOCK (Page 14) 3-3. MAIN BOARD (Page 14) 3-4. SERVO BOARD (Page 15) 3-8. CHUCKING ARM SUB ASSY (Page 17) 3-5. CHASSIS (T) SUB ASSY (Page 16) 3-9. SLED MOTOR ASSY (Page 18) 3-6. ROLLER ARM ASSY (Page 16) 3-10. OPTICAL PICK-UP SECTION (Page 19) 3-7. CHASSIS (OP) ASSY (Page 17) 3-11. OPTICAL PICK-UP (Page 19) Note: Follow the disassembly procedure in the numerical order given. 3-1. SUB PANEL ASSY 3 two claws 2 two claws 1 two screws (+PTT 2.6 u 6) 4 sub panel assy 13 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 3-2. CD MECHANISM BLOCK 6 bracket (CD) 7 CD mechanism block 5 two screws (+PTT 2.6 u 4) 2 screw (+PTT 2.6 u 6) 3 4 CN700 1 screw (+PTT 2.6 u 6) 3-3. MAIN BOARD 2 two screws (+PTT 2.6 u 8) 4 screw (+P 2.6 u 8) 5 two screws (+PTT 2.6 u 10) 6 screw (+P 2.6 u 8) 1 three ground point screws (+PTT 2.6 u 6) 7 screw (+PTT 2.6 u 10) 8 heat sink 9 MAIN board insulating sheet 3 14 Note: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 3-4. SERVO BOARD Note: In this unit, the complete SERVO board has been changed in the midway of production. When replacing the complete SERVO board, refer to “ABOUT THE MG-101CA-188 OF FORMER AND NEW” on page 6. • Former type WHT RED BLK WHT RED BLK RED ORG BLU YEL GRY 2 toothed lock screw (M1.7 u 2.5) 2 toothed lock screw (M1.7 u 2.5) SERVO board 6 SERVO board 1 Remove the eleven solders. 5 optical pick-up (16 core) (CN101) 4 claw 3 claw CD mechanism deck – CD mechanism deck bottom side view – • New type WHT RED BLK WHT RED BLK RED ORG BLU YEL GRY 2 toothed lock screw (M1.7 u 2.5) 2 toothed lock screw (M1.7 u 2.5) SERVO board 6 SERVO board 1 Remove the eleven solders. 5 optical pick-up (16 core) (CN101) 4 claw 3 claw CD mechanism deck – CD mechanism deck bottom side view – 15 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 3-5. CHASSIS (T) SUB ASSY 2 two screws (M 1.7 u 2.5) 1 two screws (M 1.7 u 2.5) 4 chassis (T) sub assy 3 claw 3-6. ROLLER ARM ASSY 6 roller arm assy 5 1 spring (RAL) 4 gear (HRA) 3 washer 2 spring (RAR) 16 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 3-7. CHASSIS (OP) ASSY 8 chassis (OP) assy 1 tension spring (KF) 5 7 two coil springs (damper) (natural) 6 coil spring (damper) (blue) 4 slider (R) 3 lever (D) 2 gear (LE1) 3-8. CHUCKING ARM SUB ASSY 3 chucking arm sub assy 1 spring 2 Note: Have this portion receive the chassis. Note: Have this portion receive the chassis. Note: Be careful not to touch the turn table. 17 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 3-9. SLED MOTOR ASSY 2 three serration screws (M 2 u 3) 3 sled motor assy 1 spring turn table spring stand Note: Never remove these parts since they were adjusted. bearing (F) stand Note: Place the stand with care not to touch the turn table. bearing (R) Note for Assembly three serration screws (M 2 u 3) sled motor assy Note: Take care to prevent the chassis from being bent when tightening the three machine screws. 18 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 3-10. OPTICAL PICK-UP SECTION 2 optical pick-up section 1 Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section. 3-11. OPTICAL PICK-UP 1 tapping screw (P 1.4) 2 leaf spring (OPS) 3 rack 5 optical pick-up 4 lead screw assy Notes for Assembly Prevent the end of the leaf spring (OPS) from being in contact with the OP slide base. – bottom side view – Prevent the end of the leaf spring (OPS) from being in contact with the OP slide base. There is space at the end of the leaf spring (OPS) to avoid contact with the slide. 19 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE MEMO 20 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM – MAIN Section – ELECTRONIC VOLUME IC401 AU_OUT_SL 40 AU_OUT_SR 39 R-CH J901 AUX R-CH R-CH 8 AUX_LCH 10 AUX_RCH R-CH 3 RF_ANT_IN J1 (ANTENNA) 4 1 AUDIO_OUT_L AUDIO_OUT_R 5 6 12 6 4 3 1 LD LD DRIVE Q710 PD FOCUS TRACK SL SP DA03(F_L_CH) DA02(F_R_CH) DA04(R_L_CH) DA01(R_R_CH) DA05(SUB_CH) ADIN1(IN_L_CH) ADIN2(IN_R_CH) 24 31 32 34 35 CD MECHANISM DECK BLOCK (MG-101CA-188) MDI FO0 TRO FMO DMO 17 5 DRV_ON LOAD EJECT L_SW IN_SW D_SW SELF 35 36 37 39 40 41 25 TU_LCH TU_RCH AU_IN_FL AU_IN_FR AU_IN_RL AU_IN_RR AU_IN_SUB AU_OUT_LCH AU_OUT_RCH AU_OUT_FR 35 AU_OUT_RR 37 I2C_SCL 22 I2C_SDA 23 27 DRV_6V MUTE Q404 R-CH XI 66 94 80 79 81 85 82 93 92 91 90 89 88 87 37 15 22 23 24 28 29 16 17 18 19 20 21 27 38 DRV_ON MEC_LOAD MEC_EJECT MEC_LIMIT MEC_INSW MEC_DSW MEC_SELFSW DEC RSTN SCL SDA R-CH 22 24 40 42 38 39 MC_RX MC_TX WAKE_UP Z_MUTE CD_ON CDM_ON 12 20 51 32 31 33 9 34 RESET SYSRST VBUS_ON FW_RXD FW_TXD FW_CLK CNVSS FW_BUSY MECHA+6V 4 CN501 FLASH PROGRAMMING 1 2 7 3 6 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 6 BU+B 37 ATT 58 AUDIO OUT FU601 16 AMP-REM ANT-REM BATT B.U+5V AUDIO+8.5V 30 31 33 34 SERVO+3.3V MECHA+6V PANEL+B 7 ACC DETECT Q301 ACC BU_IN 19 1 VOUT RXD AUDIO+B SERVO+3.3V MECHA+6V PANEL+B 16 BEEP 22 STB 25 DIAG ACC_IN 57 BACKUP VOLTAGE CHECK Q803 RESET IC403 5 5 AMP-REM 29 VP 35 VP1 20 VP2 6 D403 I2C_SCL I2C_SDA BEEP 28 AMPSTB 60 DIAG 59 D731 VBUS_ON 74 4 I2C_SCL 2 I2C_SDA J401 REAR/SUB 4 FR+ 12 FR– 3 RR+ 11 RR– R-CH BATT I2C_SDA I2C_SCL 29 I2C_SDA 30 X701 16.934MHz MECON 52 RESET 3 CD SERVO, USB CONTROL IC601 (1/2) 2 RL+ 10 RL– BATT 49 HIT2_RESET 48 HIT2_SCL 47 HIT2_SDA 89 SA_DATA 90 SA_CLK 55 56 8 54 53 OUT-RL+ 9 OUT-RL– 7 ANT-REM R-CH XO 67 TXD RXD WAKEUP ZMUTE CDON CN301 1 FL+ 9 FL– D401 MUTE DRIVE Q407,409 BU_IN 12 DRV_6V MUTE Q402 OUT-FL+ 5 OUT-FL– 3 R-CH A_ATT 51 25 R-CH (FRONT) R-CH (REAR) I2C_SCL I2C_SDA SYSTEM CONTROL IC501 (1/2) SP_DATA 95 SP_CLK 96 CD 7 9 11 13 15 57 54 59 52 61 70 74 25 LDO SRAM STB 10 R-CH SSTBY E F R-CH SCL 12 IN-FL 11 IN-RL AU_OUT_FL 36 AU_OUT_RL 38 I2C_SCL FPI1 FNI2 FNI1 FPI2 TNI TPI DEC_XMUTE BSIF_LRCK BSIF_BCK BSIF_DATA BSIF_GATE BSIF_REQ DEC_REQ 20 22 18 15 16 17 21 20 XMUTE LRCK BCK DATA GATE REQ INT B C ZDET BUS3/SI BUS2/SO BUCK/SCL RST CCE A 28 26 RSTN R-CH ZDET SO SI SCLK XRST XCCE 24 5 7 33 34 31 32 30 28 27 R-CH SDA 7 DIGITAL SIGNAL PROCESSOR IC701 CN700 R-CH I2C BUS CONTROLLED POWER AMP/MULTIPLE VOLTAGE REGULATOR IC301 MUTE Q406 9 AUX_GND TU901 TUNER UNIT -1 L -2 R VDD 2 LOW VOLTAGE CHECK Q801 D805 BATT OVER VOLTAGE CHECK Q802 BU+3.3V D806 : CD : FM TXD RESET BU+3.3V CLK 4 BU+3.3V REG IC402 5 R-CH LV RPLWWHG GXH WR VDPH DV L-CH. SLJQDO PDWK B.U+5V AM RU MW : BUS AUDIO FLASH_W BUSY BU3.3V BU+3.3V Note: CN501 has been deleted in the midway of production. 21 21 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 4-2. BLOCK DIAGRAM – DISPLAY Section – SYSTEM CONTROL IC501 (2/2) LCD CONTROL IC901 SEG48 I SEG1 94 KEYIN1 KEY MATRIX LSW905–912, S901–907 95 KEYIN0 92 KEYACK1 LCD_SO 1 LCD_CLK 2 LCD_CE 100 5 | 50 55 60 64 DATA 63 CLK LCD 62 CE COM4 51 I | COM1 54 LCD901 LIQUID CRYSTAL DISPLAY PANEL PANEL+B LED932,934,936,938, 940,942,944,946, 950,952,954 LSW905 (1/2)–LSW912 (1/2) LED901 (LCD BACK LIGHT) (NHZ W\SH) DIMMER SWITCH Q905 DIMMER 1 RE901 PUSH ENTER/SELECT (VOLUME) ROTARY ENCODER Q901 LCD BACK LIGHT DRIVE BACK-LIGHT 2 RE0 RE1 Q903 LED DRIVE 82 RE-IN0 81 RE-IN1 COLOR 1 3 18 RC_IN1 97 RC_IN0 J801 (REMOTE IN) 91 KEYACK0 USB VBUS POWER SUPPLY IC1300 BATT X502 32.768kHz X501 7.92MHz REMOTE CONTROL SIGNAL RECEIVER IC902 3 3 VIN USB_OUT 5 10 XIN 11 XOUT 15 OSCIN SYNC_OUT 26 8 SYN/EN EN_SYS 53 4 EN_SYS EN_USB 50 12 EN_USB FLT_USB 52 9 FLT_USB 13 OSCOUT 4 SIRCS SLJQDO PDWK : USB CD SERVO,USB CONTROL IC601(2/2) VBUS 80 X1 3 NOSE_SW X601 12MHz USB+ 85 USB- 86 D+ D– 1 CN902 3 2 4 (USB) 82 X2 CN601 RESET 3 72 CPON +1.5V REG IC681 5 VDD BU+3.3V SWCLK 62 SWDIO 61 SYS_RST SWCLK SWDIO 2 3 4 73 CDON_15V 1 CE OUT 4 +1.5V +1.5V REG IC682 5 VDD OUT 4 +1.5V(VDDM) Note 1: Refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7 for how to distinguish New type. Note 2: CN601 has been deleted in the midway of production. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 22 22 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.2 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. Note: • X : Parts extracted from the component side. • Y : Parts extracted from the conductor side. • a : Through hole. • : Pattern from the side which enables seeing. (The other layers’ patterns are not indicated.) Note: • All capacitors are in μF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : Internal component. • C : Panel designation. Caution: Pattern face side: (SIDE B) Parts face side: (SIDE A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. • Indication of transistor. C Q These are omitted. B E • Abbreviation AR : Argentina model CND : Canadian model IND : Indian model KR : Korean model MX : Mexican model RU : Russian model Note: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Waveforms – MAIN Board – 1 IC501 qa (XOUT) 0.9 Vp-p 32.768 kHz Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 0.5 V/DIV, 20 ȝsec/DIV 2 IC501 qd (OSCOUT) 1.2 Vp-p • A : B+ Line. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ) : AM < > : CD PLAY * : Impossible to measure • Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. J : CD F : FM f : AM L : AUX c : USB g : BUS AUDIO 7.92 MHz 0.5 V/DIV, 50 nsec/DIV 3 IC601 i; (X1) 0.7 Vp-p 12 MHz 0.5 V/DIV, 50 nsec/DIV 4 IC701 yj (XO) • Abbreviation AR : Argentina model CND : Canadian model EA : Saudi Arabia model IND : Indian model KR : Korean model MX : Mexican model RU : Russian model 2.3 Vp-p 16.934 MHz 1 V/DIV, 50 msec/DIV Note: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 23 23 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 4-3. 14 PRINTED WIRING BOARD – MAIN Section (1/2) (Except Saudi Arabia Model) – • 13 12 11 10 : Uses unleaded solder. 9 8 7 6 5 4 3 2 1 A MAIN BOARD (SIDE A) R1313 C426 R403 R411 R405 R422 R409 R432 C414 FB750 FB751 1 40 C750 FB717 R102 C748 R727 R726 C747 FB720 C729 C727 R10 R697 C759 C764 C689 R402 R421 C323 R400 FB694 C756 R764 C728 C11 C751 R524 C513 C522 R518 C523 R517 R522 CL004 81 CL003 80 Q409 R576 R541 R544 30 31 50 51 R560 R510 R511 R577 R574 R573 R572 R571 R569 R570 IFM501 S8 Barcode R122 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Note 2: When IC501 is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5. 24 24 H R121 R864 R501 R565 R566 R567 R584 R563 R562 R561 C521 R557 G C504 C510 IC501 R116 R542 C508 R430 R525 C1311 1-884-818- Note 1: Refer to SUPPLEMENT-1 for printed wiring board of the MAIN board (Saudi Arabia model). F C203 C416 R521 R529 R523 R1310 R1315 C100 R1307 C1306 E C1312 C1310 R1308 9 R1312 R1300 8 20 21 R1311 C1304 R723 D530 C401 16 C1309 C1315 2 R546 IC1300 1 C1305 C1316 D Q407 C514 C502 C520 R556 R1305 L1301 C313 IC401 R543 C1308 R1302 C1317 D1300 1 D731 20 R539 R673 R674 R603 R601 R536 R600 C683 R675 C610 C613 FB611 16 R724 R553 TP682 C410 D403 R547 C518 R548 R549 IFM601 IFM680 C420 C419 R433 R725 C752 FB718 100 1 3 C685 R661 R688 R685 C609 R401 L1300 R865 R531 R535 IC403 4 X601 C753 R717 C726 R516 R527 R538 C TP333 C737 FB719 R718 C512 R514 X501 C614 C1307 R656 TP334 R667 R655 C1301 R653 R654 TP635 R644 R646 R648 R652 CN501 TP634 R645 R690 76 75 50 51 R642 R424 C457 B C422 R410 D401 C615 R695 R669 R637 R636 TP633 1 IC601 R647 R649 R513 8 R629 R639 C612 R638 C616 FB612 1 R672 R671 FB610 R668 1 100 C601 25 26 C617 R676 C608 IFM60 R602 C605 R615 R605 R689 C606 C688 FB696 R693 R429 R515 R533 R534 TP721 R613 R606 C725 IFM50 TP724 TP723 TP722 R623 TP720 FB721 R719 R720 R716 C722 C721 R714 R617 IFM701 C792 R614 R607 IC682 C754 C730 R721 C507 R712 R711 C724 TP719 3 FB724 51 50 25 Q710 R710 TP718 26 B E C718 C717 C719 C711 C607 C744 C733 C712 R616 X701 Q406 C415 5 4 C738 FB722 C787 C786 C425 C424 FB698 C687 1 C746 C732 IC701 IC681 C735 76 75 C761 3 1 4 5 FB762 C734 C777 C789 C782 FB695 C690 R692 R552 R555 R745 TP736 100 1 C783 C784 C788 C715 C714 C713 C776 C686 TP732 FB501 C778 C771 R749 IFM70 R750 C779 R751 FB782 R715 R744 R742 C403 FB398 C308 R731 R747 R748 C766 TP741 TP742 TP743 C772 R743 R746 C768 R309 R738 C411 R761 R736 C741 R729 R728 C745 C742 R722 C739 C743 TP739 R740 R739 TP740 R741 TP735 TP733 Q404 R423 C312 R763 R733 R732 R730 TP738 C767 TP737 C720 R737 5 R305 Q405 R406 R404 C413 C309 TP734 R814 C315 Q403 C15 R301 Q801 Q802 R818 CN601 R306 C409 C398 R311 D321 R378 R300 C330 D323 R621 R618 R619 R620 R304 C321 Q402 R302 C331 Q301 C303 R303 C317 R340 R312 D806 R314 D805 R819 R820 Q803 R313 R833 R307 C326 C319 Q401 R407 C314 R308 Note 3: IC501 has been changed in the midway of production. When IC501 is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. 11, 21, 22 Note 4: C741, C743, C745, CN501 and CN601 have been deleted in the midway of production. I J CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 4-4. PRINTED WIRING BOARDS – MAIN Section (2/2) (Except Saudi Arabia Model) – • 2 1 3 4 5 : Uses unleaded solder. 6 7 8 9 10 11 12 13 14 J401 AUDIO OUT REAR/SUB J1 (ANTENNA) A -1 L US, CND, E, MX, KR, IND MODEL J801 (REMOTE IN) MAIN BOARD (SIDE B) -2 R CN301 FB803 W002 C306 16 1 8 D320 C301 FB802 9 F4 JL011 19 C334 JL012 R396 A001 JL013 D318 R395 C J801 FB801 1 37 R19 18 C305 C399 J1 FU601 17 2 C327 C335 C302 B IC301 C311 36 C332 J401 JL009 D324 AEP, RU, UK, AR MODEL AB1 4 L301 IC402 C402 JL725 R13 R12 TP761 R11 E C780 JL730 JL712 JL722 JL709 JL721 JL728 JL708 JL707 JL706 JL717 S6 JL727 JL705 JL704 JL716 JL715 R766 JL719 JL703 JL714 C716 JL702 JL713 JL718 1 2 C437 R199 TP696 JL701 JL700 R625 C438 C436 R899 JL710 JL711 TP785 C10 11 JL720 JL729 JL726 F 27 JL723 TP781 C781 L1 9 12 CN700 28 JL724 CN01 C701 R434 TP695 FB760 C760 TU901 TUNER UNIT (TUX-DSP02) AEP,UK MODEL D306 R765 FB19 1 3 R699 D C407 5 FB890 FB891 R431 13 10 1 W001 JL010 R622 JL008 R419 SERVO BOARD TP644 X502 IFM500 R604 R578 R579 R564 IFM502 TP640 R417 C440 C442 C501 C503 D103 CL061 D102 D101 JL002 R502 JL005 JL004 JL006 CL077 CL079 CL075 CL071 CL073 CL066 CL069 JL003 CL081 JL731 JL007 R568 CL067 JL001 R1301 CL082 C103 CL074 CL076 CL072 CL070 CL063 CL068 CL064 CL065 C101 JL732 TP643 R545 R420 C439 R415 R416 CD MECHANISM DECK BLOCK (MG-101CA-188) JL733 R643 TP641 R586 D119 R418 I TP342 TP632 R575 H OPTICAL PICK-UP BLOCK (DAX-25A) TP642 R540 G SENSOR BOARD D110 CL078 1-884-818- 19 21 1 11, 21, 22 20 2 22 CN102 A KEY BOARD CN901 (Page 31) Note 1: Refer to SUPPLEMENT-1 for printed wiring board of the MAIN board (Saudi Arabia model). CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Note 2: When the SERVO board is defective, exchange the complete mounted board. (Refer to Note 4) Note 3: When the SENSOR board is defective, exchange the MECHANICAL BLOCK (Z) ASSY 08 (Former type) or MECHANICAL BLOCK (11CA) ASSY (New type). (Refer to Note 4) 25 25 Note 4: As for the mechanism deck (MG-101CA-188) carried in this unit, component parts have been changed from the midway of production. When you perform repair exchange of the mechanism deck (MG-101CA-188), refer to “ABOUT THE MG-101CA-188 OF FORMER AND NEW” on page 6. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 IC301 2 RST ANT-REM CRES BU+B DIAG CBU P-GND4 35 36 37 3.3 5.1 OUT-FR- VP STB 34 13.8 OUT-FR+ PANEL+B VP1 33 14.4 OUT-RR- MECHA-6V P-GND3 32 31 10.5 OUT-RR+ GND BEEP 30 6.2 IN-RR 29 13.5 IN-FR 1 S-GND 3.3 IN-FL 1 IN-RL 1 SVR 1 OUT-RL+ 4.3 P-GND1 4.3 OUT-RL- 4.6 VP2 7 OUT-FL+ 7 I2C_SCL 7 14.4 OUT-FL- 3.3 I2C_SDA 7 TAB 28 FB398 R396 0 C323 1000p 0 R340 R300 0 C308 C312 0.22 10 16V 1 R395 0 C309 220 6.3V C326 47p F4 2A 36V C311 0.22 C306 1 0.47 10k 10k C399 1 C302 C305 1 R308 0 2.2 R307 150 C314 C327 1 C321 R311 R378 C313 47 16V C301 0.22 6.3 BATT D805 RKZ7.5B2KGP1 C331 0.47 R819 1k D806 RKZ18B2KGP1 C330 0.47 R818 220k 2.7 R314 4.7k Q803 2SC4154TP-1EF F 0.6 Q407,409 MUTE DRIVE IC403 R400 0 RESET ACC IC402 BU +3.3V REG IC403 PST8228UL 3.3 Q803 BACKUP VOLTAGE CHECK R401 100k 3.3 1 VOUT 2 Vdd IC B/D VSS 4 C403 220 6.3V NC 3 C401 0.1 C402 1 4 5 3 2 1 5.1 FB801 D401 DA2J10100L GN1G 47k 1 2 3 4 5 R313 47k Q301 0 2SC4154TP-1EF ACC DETECT R814 220k D321 C335 0.1 R312 47k 0 R820 Q802 1k DRC5114E0L OVER VOLTAGE CHECK 0 C334 3300 16V JL010 R309 R429 22 0 Q407 DRA5114E0L R430 0 13.8 C407 0.1 C409 1000 6.3V C411 220 6.3V 13.5 C416 47 25V 6 0 7 8 R833 100k XM_RX RCIN0 RCIN1 R434 0 R433 0 9 BU_3.3V 0 FB890 FB891 R513 100k 21 20 BUS6 19 BUS5 18 17 R864 0 15 H 1 (Page 29) R899 16 MAIN BOARD (4/5) VDD_3.3V DR_6V DR_GND A_GND D_GND BU_GND AU_GND SYS_RST USB_GND 2 MAIN BOARD (2/5) I CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE (Page 27) 26 26 3 MAIN BOARD (3/5) (Page 28) Q409 DRC5114E0L 0 FB802 FB803 G 27 4 Q801 DRC5144E0L LOW VOLTAGE CHECK J801 (REMOTE IN) 26 DIAG 1 25 STB 4 24 5.1 3 23 3.3 6 22 NP VOUT GND CONT VIN 5 GND 21 IC402 MM1836A33NRE E 8 20 BEEP ANT REM 7 19 3.3 3 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 D ACC 18 220 BATT 17 C303 22 16V 16 16 100 8 15 R302 GND BATT 14 100 15 13 R301 7 12 JL012 15 16 ACC ATT 11 220 7 8 14 10 R303 14 6 9 0.47 6 ANT REM 11 8 C317 13 FR- 3 7 220 12 5 13 10 +B +B +B +B TEST ILL TEL-ATT FRRRRLFLGND ACC ANT-REM AMP-REM FR+ RR+ RL+ FL+ 6 0.47 4 12 5 RL- 2 FU601 10A 32V 5 C315 11 4 RR- 9 4 R304 GND 3 10 FL- 1 3 220 ACC 2 9 FRONT + L-CH REAR + L-CH REAR + R-CH FRONT + R-CH AMP REM 2 R305 ANT REM 1 CN301 16P RR- 1 L301 140uH NEW JL013 AMP REM 2 JL009 I2C_SCL C FR+ 1 US, CND, E, EA, MX, KR, IND MODEL +B I2C_SDA RL+ RR+ 4 FR- D318 GN1G FL+ 3 JS1 1 FL- 14 IC301 TDF8556AJ/N5 RESET B 6 D324 GN1G RR+ 5 AEP, UK MODEL D306 GN1G RL- D323 RKZ18B2KGP1 FR+ 8 C398 0.001 FL+ 7 D320 RKZ18B2KGP1 RL+ 13 12 IC B/D IC2 BUS CONTROLLED POWER AMP/MULTIPLE VOLTAGE REGULATOR AEP, RU, UK, AR MODEL 11 3.3 MAIN BOARD (1/5) A 10 AMP-REM 9 AUDIO+B (8.5V) SERVO-3.3V 8 8.6 7 14.4 6 4.5 5 4.3 4 3 R306 2 4.3 1 • See page 33, 34 for IC Block Diagrams. 0.47 SCHEMATIC DIAGRAM – MAIN Section (1/5) – C319 4-5. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 4-6. SCHEMATIC DIAGRAM – MAIN Section (2/5) – 1 2 3 • See page 23 for Waveforms. • See page 35 for IC Block Diagrams. • See page 37 for IC Pin Function Description of IC501. 4 5 6 7 8 9 10 13 14 21 20 BUS6 19 BUS5 18 17 16 2 15 12 (Page 26) MAIN BOARD (1/5) A 11 MAIN BOARD (2/5) D1300 DB2X41400L 1 C1304 47 8 SYNCFLT_USB 3.3 C1309 0.01 0.1 R1305 5.6k 0.5% 1.1 C1317 0.01 C1305 22 R1313 220k R1308 82k 0.5% C1306 680p C1312 0.01 D403 MC2838-T112-1 VBUS_ON EN_SYS FLT_USB ACC 100 100 R572 R571 3.1 3.3 100k 100 R573 3.3 3.3 100k 10k R578 R586 0 0 0 3.3 3.3 0.1 100k C504 R569 FLT_USB VBUS_ON IPOD EN_SYS EXTATT_XEN TELATT ATT ACC_IN DIAG AMPSTB CYRIL_SEL 100 2.6 R511 100 3.1 R584 100k EJECT_OK BEEP SYNC_OUT DOOR_ING DOOR_SW MC_TX 12 BUS3 R564 100 WAKE_UP 3.3 CDM_ON 3.3 CD_ON 0 XM_RX R563 100 0 R562 0 F_RXD 0 R561 0 F_TXD 0 13 BUS4 14 BUSY I2C_SDA F_CLK I2C_SDA I2C_SCL 100k 47p 47p C520 2.2k R557 C521 2.2k R552 R556 R553 0 100k R555 FB501 0.047 100k R546 C518 0 R549 11 Z_MUTE 3.3 0 (Page 28) 10 R565 100k 0 3.3 I2C_SCL 3.3 0 1.1 R566 100k R567 100k 470 3.3 MC_RX 3.3 SYSRST BUS_ON 3.3 BUIN NMI RC_IN1 2.8 0 VCC1 3.1 3.1 100 VSS OSCIN 3.3 1.7 OSCOUT RESET XOUT XIN R545 R547 R548 R531 100k 0 R560 VSS VCC2 F_AUX_ATT BT_MUTE COLSW SEL ILLUMI SEL AREASEL2 AREASEL3 B-OUT SEL AREASEL1 AREASEL0 MODELNAME_SEL0 MODELNAME_SEL1 100k R536 100k 1 D530 RB751V40,115 R510 C1310 0.1 R1307 82k 0.5% C1311 100 16V 1.7 470 3.3 R535 1.5 NOSE_SW R865 0 C508 18p CAM001 X502 32.768kHz C507 22p R1312 10k 0.5% MODELNAME_SEL2 BT_TX BT_RX 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 0 EN_USB 8 5.9 R1300 470 R1311 39k 0.5% 1k R1302 100k 3.1 9 7 EJECT_OK 11 10 1k R534 2.7 3.3 MAIN BOARD (3/5) BEEP 5.2 6 SYNC L1301 47uH 12 5 RXD 0 4 TXD 0 C1316 * 3 17 C1315 22 13 R533 LCD_CLK FW_RXD 32 FW_TXD 31 2 SIRCS 1.7 GNDA 14 4 EN_SYS SS_SYS 5 USB_OUT EN_USB 6 FB_US VIC_USB USB_IN 7 ISET_USB LCD_DATA 2 RCIN1 C1301 1 3 VIN C1308 2.2 6.2 1 1 100 LCD_CE C510 3.3 RT 15 2 LX 0.2 R529 470 FW_BUSY 34 FW_CLK 33 98 AVRH 99 AVDD RESET 14.2 VREF 16 96 AVSS 97 RC_IN0 3.3 CNVSS 4.6 1 BST 3.3 10k 9.2 0.01 3.3 FLT_USB IC1300 USB VBUS POWER SUPPLY R1301 IC1300 100 OZ539IGN-A1-0-TR 100 100k L1300 0 C1307 0.01 * C1316 0.1 (EXCEPT EA) 1 (EA) SYNC EN_SYS IC B/D C513 XM_RX 36 XM_TX 35 R540 E R525 R516 10k 0.5% LCD_CE 3.3 100 0.3 RCIN0 R524 CNVSS 1000p BYTE C502 0 KEY0 94 KEYIN1 95 KEYIN0 CD_ON 38 XM_POWER EN 37 UNISCK 3.3 EPM 41 WAKE_UP 40 CDM_ON 39 UNISI KEY1 R523 100 92 KEYACK1 93 BT_MIC_ON 3.3 JL001 R515 10k 0.5% IC501 R5F3650KBDZ78FA (Former type) R5F3650KBDZ75FA (New type) SYSTEM CONTROL 90 SA_CLK 91 KEYACK0 R538 8 R514 10k 0.5% 3.3 UNISO GND 3.3 CNVSS JL002 3.3 R/S SW_SEL 43 Z_MUTE 42 IC501 0 7 JL008 SA_CLK 88 BT_MIC_DET 89 SA_DATA 100k FLASH_W F_RXD 2.8 0 6 JL003 SA_DATA R527 5 F_TXD 100 3.3 5 EN_USB R570 INITCOL_SEL 45 EQ_TYPE_SEL 44 86 BT_RESET 87 BT_POWER R539 RXD BU3.3V BUSY JL004 HIT2_SDA 47 CE 46 SIRCS 4 JL005 EN_USB 50 HIT2_RESET 49 HIT2_SCL 48 NOSE_SW TXD F_CLK JL006 83 ILL_IN 84 BT_RTS 85 BT_CTS 3.1 3 1000p 2 1000p CLK BUSY RESET JL007 C514 1 C512 RESET D731 BAT54ALT1G CN501 8P 81 RE-IN1 82 RE-IN0 MODELNAME_SEL3 0 DEBUG_1 0 RE0 LCD_CLK USB_D+ DEBUG_2 RE1 R501 100k R574 100 LCD_SO USB_D- R517 1k R518 1k G A_ATT EXCEPT EA MODEL 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A_ATT A_ATT 0 Z_MUTE Z_MUTE 3.3 VBUS_ON R577 3.3 VBUS_ON USB_D+ F CL003 CL004 0.01 33k 0.01 33k CD_ON R522 CDM_ON CD_ON C523 TXD CDM_ON C522 TXD USB_D- FLASH D (PROGRAMMING ) R568 100k R502 100k 47p 10k R521 C R579 RXD RXD (Page 30) 100k EJECT_OK SA_DATA SA_DATA 4 100k R576 SA_CLK SA_CLK MAIN BOARD (5/5) R575 47p EJECT_OK BU_IN WAKE_UP C501 WAKE_UP C503 BU_IN B DIAG STB BUS2 R1315 1k R541 10M R543 0 R544 1M X501 7.92MHz R542 220k R1310 1k H Note 1: When IC501 is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 27 Note 2: IC501 has been changed in the midway of production. When IC501 is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. 27 Note 3: CN501 has been deleted in the midway of production. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 4-7. SCHEMATIC DIAGRAM – MAIN Section (3/5) – 1 2 • See page 36 for IC Block Diagrams. 3 4 5 6 7 8 10 9 12 11 MAIN BOARD (3/5) A 1 2 3 WHT 4 -1 J401 L 5 REAR/SUB RED R AUDIO OUT -2 G 6 B MAIN BOARD (1/5) R406 0 3 (Page 26) Q401 LTC014TUBFS8TL 0 7 8 JL011 0 0 R409 10k C Q402 LTC014TUBFS8TL 9 Q403 LTC014TUBFS8TL Q404 LTC014TUBFS8TL 0 0 0 0 R407 1k R421 1k R423 1k C413 10 16V C424 10 16V C425 10 16V Q401-406 MUTE 0 0 R411 10k C457 0.01 Q406 LTC014TUBFS8TL 0 0 R424 10k R422 10k Q405 LTC014TUBFS8TL 0 R405 10k R403 10k R410 1k R404 1k R402 1k C420 10 16V C422 10 16V C410 10 16V J1 (ANTENNA) IC401 D 4 R431 0 4 L1 4.7uH 38 AU_OUT_RL NCO 3 4 AU_OUT_RR 37 NCO 4 4 3.6 AU_FR_CH 3.6 AU_FL_CH 3.6 AU_RR_CH MAIN BOARD (4/5) 6 (Page 29) 3.6 AU_RL_CH 3.6 AU_SUB_CH 1 40 AU_OUT_SL BUS_LCH AU_OUT_SR 39 BUS_RCH 2 4 4 E F IC B/D IC401 BD3467FV-E2 ELECTRONIC VOLUME AU_IN_LCH 4 AU_IN_RCH 8.5 C414 R432 0.1 10k BUS2 G C415 220 16V C419 10 16V 3.7 R199 AU_OUT_FR 35 TU_GND 6 3.2 34 AU_IN_FR TU_RCH 7 3.2 33 AU_IN_FL AUX_LCH 8 3.2 C436 AU_IN_RR AUX_GND 9 3.2 C438 31 AU_IN_RL 10 AUX_RCH 3.2 30 AU_IN_SUB XM_LCH 11 NCO R13 C437 1 2.2 1 AU_OUT_LCH XM_RCH 13 27 AU_OUT_RCH FP1 14 26 VCC(8.5V) FN1 15 25 FIL FN2 16 24 GND FP2 17 3.3 23 I2C_SDA I2C_SCL 3.3 22 I2C_SCL 21 MUTE NCO NCO NCO 0 1k R10 0 R11 0 R12 0 R417 12k R418 12k R416 1k R420 0 C440 1000p C439 1000p RF_ANT_IN 3 4 AUDIO_OUT_L 5 6 RSTN 8 C10 1 9 C11 47 16V 13 1 2 7 C15 1 XM_GND 12 28 I2C_SDA 8.4 10 3.2 32 CAM002 0 R102 AU_OUT_FL TU_LCH 5 36 29 4 R19 FB19 RF_GND AUDIO_OUT_R TU901 TUNER UNIT (TUX-DSP02) SCL SDA +8.5V POWER_GND 11 12 R415 1k C442 0.1 D119 RKZ6.8B2KGP1 C101 1000p CL061 CL063 USB_D- R122 0 CL064 USB_D+ R121 0 CL065 18 CL066 C100 19 0.1 CL067 CL068 20 CL069 CL070 R419 2.2k (Page 27) 10 11 12 CL072 KEY1 CL073 KEY0 CL074 SIRCS CL075 LCD_DATA CL076 LCD_CE CL077 LCD_CLK CL078 CL079 NOSE_SW D101 RKZ6.8B2KGP1 R116 0 BUS3 C203 1000p I RE1 13 D110 RKZ6.8B2KGP1 5 CL071 D102 RKZ6.8B2KGP1 H MAIN BOARD (2/5) RE0 C103 0.1 BUS4 14 CAM003 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 28 28 CN102 20P 1 USB_GND 2 USB_VBUS 3 D- 4 D+ 5 GND 6 KEY_GND 7 AUX_L 8 AUX_R 9 AUX_GND 10 RE_0 11 RE_1 12 KEY_1 13 KEY_0 14 SIRCS 15 LCD_DATA 16 LCD_CE 17 LCD_CLK 18 ILL(FP+B) 19 PANNEL_SW 20 GND A KEY BOARD CN901 (Page 32) CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 SCHEMATIC DIAGRAM – MAIN Section (4/5) – 3 2 4 5 6 7 8 9 10 MAIN BOARD (4/5) DRV_ON JL703 SELF JL702 JL701 JL700 24 21 DRV_GND F 22 19 BU_GND E 20 17 D_SW OP_VCC 18 15 IN_SW 1/2VCC 16 13 L_SW OP_GND 14 11 EJECT PD 12 9 LOAD LD 10 7 DRV_ON DRV_VREF 8 5 SELF FOCUS 6 3 SL TRACK 4 1 SP OP_GND 2 470p C716 0.047 470p C715 C714 C713 0.047 A R715 0 JL720 C720 0.1 JL716 C721 0.1 JL714 0.01 0.1 C777 C778 100 0.01 2200p R745 C784 TP785 C779 0 C789 0 R746 0.015 0 R747 RFO 0 R748 TP781 RFAC 3.2 LPFO 1.6 0.9 VCOF PVREF 1.6 VCOI RVSS3 3.2 1.7 RVDD3 DCOFC RFO AGCI RVSS3 FNI2 FNI1 FPI2 FPI1 VDD1-1 TPI TNI 1.6 SLCO 1.6 1.6 1.4 0.6 1.6 1.6 1.6 1.6 1.5 1.6 1.6 1.6 1.6 RFI BSIF_GATE 89 BSIF_REQ 88 IC701 TC94A99FG-003 (SY) DIGITAL SIGNAL PROCESSOR 38 VDD1-2 39 VDD3-1 DEC_REQ 87 VDD1-4 86 40 CD-MON2/PIO10 TP720 JL715 IC701 37 /SRAMSTB 3.2 JL717 BSIF_BCK 91 BSIF_DATA 90 35 DMO 36 VDDM1 1.5 C722 0.1 JL718 VRO 34 FMO 3.3 JL719 DEC_XMUTE 93 BSIF_LRCK 92 33 VSS-1 1.5 C792 0.1 CD-MON0 / SP_DATA 95 ZDET 94 32 TRO 1.6 JL721 0 30 AVDD3 31 FOO 1.6 JL722 MDI 29 TEI /RST 85 TP721 41 CD-MON3/PIO11 TP722 42 PIO12 / DT/BT_DATAi VSS-3 84 VDD3-2 83 /CCE 82 JL713 TP723 43 PIO13 / DT/BT_BCKi PIO15 / SDo0 PIO16 / SDo1 JL712 TP724 44 PIO14 / DT/BT_LRCKi PIO17 / SDo2 45 PIO18 / LRCKo 46 PIO19 / BCKo 47 PIO20 / Cko BUCK/SCL 81 BUS3/Si 80 BUS2/So 79 BUS1 78 ADVCM ADVREFH ADVREFL ADIN1 (IN_L-CH) XVDD3 ADVDD3 XO XI 4 VSS-2 XVSS3 VDD1-3 DVSS5 DAO5 (SUB-CH) DVDD5 DVSS34 DAO4 (R_L-CH) DAO3 (F_L-CH) DVDD34 DVREF DAO2 (F_R-CH) DVDD12 E DVSS12 49 50 DAO1 (R_R-CH) 48 BUS0 77 MS 76 R743 15k 1.3 0 C771 47p R742 47k 1.6 BUS7 3.3 TP743 R741 100 2.7 TP742 R740 1k 0 TP741 R739 1k 3.3 TP740 23 24 0 25 0 26 0 TP739 0 TP738 R738 0 TP737 R737 1.5 3.3 TP736 TP735 TP734 0 TP733 R733 0 TP732 R732 0 330 C752 35V 4.7 FB719 0 R719 330 C753 35V 4.7 FB720 0 2.2 FB721 0 R720 R721 330 C754 C732 1000p C724 0.1 C725 22 6.3V R723 34 0 0 35 BUS8 BUS9 2.2 C743 150p C744 2.2 C745 150p C746 2.2 MAIN BOARD (5/5) (Page 30) 150p C742 7 37 27p 10k FB762 0 33 2.9 1.5 2.6 1.6 0.6 1.5 3.2 3.2 1.3 1.5 1.6 3.2 1.6 1.6 3.2 1.6 1.6 1.4 1M X701 16.934MHz C734 C748 R722 330 R716 0 R727 C747 C730 C741 FB722 0 31 32 100k C739 0.1 FB724 330 R718 30 0 C733 0.1 1.5k R717 0 C726 G 1.6 3.2 0 FB718 2200p FB717 4.7 2200p 4.7 35V 3300p 35V C751 10k C750 3300p AU_SUB_CH 2.2 R726 AU_FL_CH AU_RL_CH 2.2 C738 3300p AU_FR_CH C737 2.7k 3300p (Page 28) AU_RR_CH 2.7k R725 C729 6 R724 C728 MAIN BOARD (3/5) 0 0 3300p F FB750 29 C767 0.1 3.3 R736 28 C768 0.1 3.2 0 27 1k 1k 36 TP761 FB751 C727 AU_IN_LCH AU_IN_RCH 0 22 0 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 R764 SA_CLK SA_DATA 0.01 JL704 DRV_GND TMAX 99 PDO 98 TEST 97 CD-MON1 / SP_CLK 96 27 RFZI 1.6 R714 0 JL723 R744 330k LPFN 100 28 RFRP 1.6 JL724 1 100k LOAD 23 3.2 2 C766 D EJECT JL706 JL705 26 TE JL725 3 100k L_SW 28 C 1.6 4 R731 JL707 B DRV_6V 1.6 TP719 5 100k JL708 IN_SW DRV_6V 25 6 R730 D_SW 27 7 100k JL709 CN700 28P 8 26 FSMONIT 0.8 C717 0.1 9 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 TP718 FE/SBAD R729 JL710 1.6 C719 5600p R728 C701 0.1 C786 0.1 R710 1k ADIN2 (IN_R-CH) ADVSS3 C JL711 C772 0.015 C718 0.033 CD MECHANISM DECK BLOCK (MG-101CA-188) R765 0 C712 47 4V C711 0.1 SERVO BOARD C788 1000p C782 0.1 FB782 JL727 IOP+ JL726 IOP- 3.2 R712 3.3 AVSS3 OPTICAL PICK-UP BLOCK (DAX-25A) R711 10 22k 22k C780 5600p C781 0.1 C783 0.1 LDO Q710 2SA1365-T112-1EF LD DRIVE 0 3.2 R750 R751 C776 0.1 JL729 VC R749 A SENSOR BOARD 13 JL730 JL728 B 12 11 C787 0.1 RFRPI 1 • See page 23 for Waveforms. • See page 39 for IC Pin Function Description of IC701. RFEQO 4-8. C735 0.1 38 39 C759 0.01 H DR_GND BU_GND USB_GND R699 0 C685 1000p AU_GND MAIN BOARD (1/5) 1 (Page 26) I C756 1000p R763 0 C764 1000p C761 0.1 FB760 0 R761 0 C760 0.1 40 R766 0 41 DR_6V A_GND D_GND 42 SYS_RST VDD_3.3V BU_3.3V C686 1000p Note 1: When the SERVO board is defective, exchange the complete mounted board. (Refer to Note 3) CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 43 Note 2: When the SENSOR board is defective, exchange the MECHANICAL BLOCK (Z) ASSY 08 (Former type) or MECHANICAL BLOCK (11CA) ASSY (New type). (Refer to Note 3) 29 Note 3: As for the mechanism deck (MG-101CA-188) carried in this unit, component parts have been changed from the midway of production. When you perform repair exchange of the mechanism deck (MG-101CA-188), refer to “ABOUT THE MG-101CA-188 OF FORMER AND NEW” on page 6. 29 Note 4: C741, C743 and C745 have been deleted in the midway of production. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 4-9. SCHEMATIC DIAGRAM – MAIN Section (5/5) – 1 3 2 • See page 23 for Waveforms. • See page 36 for IC Block Diagrams. • See page 42 for IC Pin Function Description of IC601. 4 5 6 8 7 9 10 USB_D- USB_D+ A EJECT_OK WAKE_UP BU_IN MAIN BOARD (5/5) TP643 C616 0.1 R623 0 IC681 TP695 37 FB695 0 3.3 4 5 VOUT VDD NC 3 GND 2 CE 1 0 10k R667 3.2 TP635 49 MECON_CHECK 50 CDON_CHECK 2.8 TP634 48 NC 3.2 TP633 46 FE/SBAD_SEL 47 Z/Y_SEL A-ATT 100 VBUS_ON 3.3 0 0 0 0 0 100k 100k 100k 100k R655 R656 3.3 100k 3.1 R654 0 C609 0.1 RXD 100 TP641 3.3 R648 100 TP640 0 R647 100 Z_MUTE 3.3 R646 100 CD_ON R649 3.3 TXD 3.3 R645 100 CDM_ON 0 R644 100 A_ATT R643 100k R639 10k R638 33k R642 10k 3.3 R693 0 TP333 USB_D- FB694 0 A_ATT Z_MUTE VBUS_ON IC682 I 39 TP696 FB696 0 3.3 40 C688 2.2 CD_ON CDM_ON +1.5V REG IC682 NJM2878F3-15 (TE2) 1.5 4 VOUT NC 3 GND 2 5 VDD CE GND R692 0 C690 1 38 SWDIO 5 3.3 3.3 1.4 0 0 XT1 77 REGVCC3 76 XT2 78 CVCC3 79 X1 80 1.6 3.3 DVSS 84 CVSS 81 45 XINIT0 44 XLINE 43 NC 42 NC TP632 MECON R661 3.3 USB_D+ C689 2.2 SWCLK 4 IC B/D +1.5V REG IC681 NJM2878F3-15 (TE2) 1.5 SYS_RST 3 FB610 0 R653 4.7 41 MEC_DSW 39 MEC_LIMIT 40 MEC_INSW 3.2 33k D_SW R637 BUS9 (Page 29) H IN_SW SELF L_SW BUS8 7 VCC 2 R636 4.7k R625 100k DRV_ON 36 C608 TP342 35 MAIN BOARD (4/5) DVCC3 83 0 0 USB+ 85 3.2 NMI 87 USB- 86 TEST 88 0 TEST 89 0 3.3 0 0 0 0 0 0.1 34 G NC 90 NC 91 AVCC3 92 NC 93 NC 94 NC 95 NC 96 NC 97 NC 98 0 0 33 F 0 CD_SCLK MEC_SELFSW 38 DEC_SSTBY 32 CDON CD_SI R622 10k C607 0.01 31 ZMUTE CD_SO 3.3 3.3 TxD 3.2 3.3 RxD DEC_REQ 37 MEC_EJECT 1k DEC_GATE 0 R620 DEC_DATA NC NC DEC_BCK 3.3 0 DVCC3 DEC_LRCK EJECT 1k DVSS DEC_XMUTE 35 DRV_ON 36 MEC_LOAD R619 SWDIO 0 0 0 CD_ZDET LOAD 1k CP_SCL CP_SDA SWCLK 34 DVSS R618 CPON CP_RESET NC 0 0 CDON_15V TRACECLK 100 100 DVSS R629 R621 NC 99 NC 100 0 0 TRACEDATA0 BU_IN 32 Z/Y_CHECK 33 DVCC3 30 0 IC601 M321FEFG-7KN3 (SY CD SERVO, USB CONTROL NC 3.3 29 0 1k 1k IC601 TRACEDATA2 TRACEDATA1 31 NC 28 1k R616 R617 TRACEDATA3 NC 30 NC 27 0 NC VBUS_ON NC 29 CD_XCCE E R615 10k WAKEUP 3.3 26 R614 NC 27 DEC_INT 25 0 EJECT_OK 28 CD_XRST 24 2.7 OPEN_REQ 26 NC 23 R613 47k C605 0.01 MODE 3.3 22 R607 100k 1 BUS7 2 D C606 0.01 3 3.3 RESET 4 3 NC VREFH 5 0 3 AVSS 6 0 FB612 7 R606 100k R604 100 R669 0 8 3.2 TP642 1 C610 1000p 9 TP644 3.3 FB611 C612 0.1 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 C601 0.1 JL733 C613 0.1 R652 1 R605 100k C R672 X601 12MHz 100 R601 100 R602 R600 100 100 R603 R668 1M C615 10p C617 0.1 R675 100k R671 R676 100k 4.7 R695 0 2 B JL732 X2 82 C614 10p JL731 R673 15k 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 R674 15k CN601 5P 1 TXD 0 RXD R697 0 SA_DATA SA_CLK 3.3 FB698 0 TP682 R688 0 R689 0 R685 0 EJECT_OK WAKE_UP BU_IN C687 1 USB_D+ USB_DA_ATT Z_MUTE VBUS_ON CD_ON CDM_ON TXD RXD SA_DATA 4 MAIN BOARD (2/5) (Page 27) SA_CLK EJECT_OK WAKE_UP BU_IN 41 J C683 0.1 42 R691 33k 43 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 30 30 R690 30k Note: CN601 has been deleted in the midway of production. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 2 1 3 A R920 R921 8 9 10 11 12 13 LED901 (LCD BACK LIGHT) 14 LED946,S901 Z S901 R954 LED938 52 1 R903 S906 R970 LED901 LCD901 LIQUID CRYSTAL DISPLAY PANEL LED944 LED952 R952 LED942 S907 R990 LSW911 LSW912 LSW909 R984 LSW910 LSW907 LSW908 LSW906 LSW905 R980 S905 LED954 LED932 LED934 LED933,934,S905 m . SEEK - 7 KEY BOARD (SIDE A) LED932,S904 LED954,S906 6 LED950 LED940 S904 C 5 R982 B 4 S902 R946 S903 : Uses unleaded solder. LED950,S902 SOURCE / OFF LED936 LED936,S903 SEEK + > M • LED946 4-10. PRINTED WIRING BOARD – KEY Section – 11 1-884-821- D LED952,S907 MODE LSW912 LED938,940,942 (ILLUMINATION) AF/TA/ PTY (AEP, RU, UK) LSW911 LSW910 LSW909 LSW908 LSW907 LSW906 1 /ALBUM V 2 /ALBUM v 3 /REP 4 /SHUF 5 /ZAP 6 /PAUSE (11) LSW905 / DSPL SCRL PTY (EXCEPT AEP, RU, UK) E (Page 25) MAIN BOARD CN102 J901 A KEY BOARD (SIDE B) C901 C903 C902 C904 IFM1 R976 64 IC901 49 48 2 J901 IFM4 R902 R907 R998 16 17 CN902 33 32 R972 R927 IFM2 R922 CN902 R906 C912 R991 R910 R918 1 D902 D916 Q901 19 C916 1 CN901 20 R901 R908 R917 D901 R992 D912 R958 R993 IFM6 R956 R974 Q903 R909 Barcode RE901 R940 C909 C910 R986 R999 R925 R942 R944 R915 R904 R926 R924 R923 G IFM3 R994 R995 C915 R996 D911 R997 R988 R950 R966 C906 IC902 R968 IC902 C911 R916 F H AUX (USB) R919 FB901 I RE901 FB902 PUSH ENTER/SELECT 11 1-884-821- Note 1: Refer to the servicing notes “NOTE FOR REPLACEMENT OF THE USB CONNECTOR (CN902) AND THE AUX JACK (J901)” on page 4, if replacing CN902 and J901. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE FB903 R905 R948 31 31 (11) Note 2: IC901 has been changed in the midway of production. Moreover, the KEY board has been changed simultaneously with it. Before repairing, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 4-11. SCHEMATIC DIAGRAM – KEY Section – 12 S[9] S[10] S[11] S[12] S[13] S[14] S[15] S[16] S[17] S[18] S[19] S[20] 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 KEY BOARD A 5 3 1 6 4 2 R994 1.2k C915 1000p R952 *4 LSW909 R958 *5 *3 R995 1.5k R984 *7 *4 R940,944 220 (AEP,RU,UK) 820 (EXCEPT AEP,RU,UK) R946,950,954,956,970,972 270 (AEP,RU,UK) 1k (EXCEPT AEP,RU,UK) R948,952,968 330 (AEP,RU,UK) 1.2k (EXCEPT AEP,RU,UK) 4 3 R926 2.2k S907 MODE LED938,940,942,944 (ILLUMINATION) 5 LED950 *1 SOURCE / OFF F R968 *4 LED952 *1 MODE G *1 H R958,974 270 (AEP,RU,UK) 1.2k (EXCEPT AEP,RU,UK) *6 R966 330 (AEP,RU,UK) 1k (EXCEPT AEP,RU,UK) 2 R996 1.8k R986 *7 *7 *8 R972 *3 R927 0 R974 *5 LED932,934,936,938,940,942,944,946,950,952,954 SML-D12P8WT86TK (AEP,RU,UK) SML-D12V8WT86TN (EXCEPT AEP,RU,UK) 5 3 1 6 4 2 PTY R980,982,984,986 100 (AEP,RU,UK) 150 (EXCEPT AEP,RU,UK) R988 150 (AEP,RU,UK) 220 (EXCEPT AEP,RU,UK) R990 180 (AEP,RU,UK) 220 (EXCEPT AEP,RU,UK) R997 2.2k R988 *8 LSW912 AF/TA/ PTY (AEP,RU,UK) R918 0 *9 LSW911 1/ALBUM RE901 PUSH ENTER/ SELECT R919 0 5 3 1 6 4 2 (EXCEPT AEP,RU,UK) R990 *9 R999 0 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG12 SEG13 SEG11 SEG10 SEG9 SEG7 SEG8 SEG6 SEG5 61 INH 62 LCD_CE SEG33 20 SEG34 19 63 LCD_CLK 64 LCD_DATA SEG35 18 SEG36 17 8 9 10 11 12 13 14 15 16 S[28] 2.6 S[29] 2.6 S[30] 2.6 S[31] 2.6 S[32] 2.6 S[33] 2.6 S[34] 2.6 S[35] 2.6 S[36] 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 S[43] S[42] S[41] S[40] S[39] S[38] S[37] SEG37 7 SEG38 6 SEG39 5 SEG40 4 SEG41 3 SEG42 2 SEG43 SEG44 1 S[44] R917 470 SEG45 0.2 SEG46 DATA 2.6 470 3.3 2.6 0.1 S[45] R916 S[46] CLK 470 SEG47 R915 2.6 CE SEG48 S[1] S[27] 2.6 LCD901 LIQUID CRYSTAL DISPLAY PANEL COM[1] COM[2] COM[3] COM[4] S[48] S[47] S[46] S[45] S[44] S[43] S[42] S[41] S[40] S[39] S[38] S[37] S[36] S[35] S[34] S[33] S[32] S[31] S[30] S[29] S[28] S[27] S[26] S[25] S[24] S[23] S[22] S[21] S[20] S[19] S[18] S[17] S[16] S[15] S[14] S[13] S[12] S[11] S[10] S[9] S[8] S[7] S[6] S[5] S[4] S[3] S[2] S[1] 1 I 4 LED954 *1 6 *5 1 LSW910 2/ALBUM R970 *3 R966 *6 3 GND OUT VCC 5.1 5.2 5.1 *2 3/REP R948 *4 SEG31 22 SEG32 21 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 R956 *3 2.6 59 VSS 60 SEG52 S[26] 2.6 8 R925 1.8k 1.7 S[25] 2.6 7 2 0.1 SEG29 24 SEG30 23 S[24] 2.6 6 (USB) 2 1 C916 1000p GND-USB 4 C901 57 VDD1 58 VDD2 S[23] 2.6 5 6 3.4 S[22] 2.6 4 SEEK- 0.1 LSW908 Q903 RT6N140C-TP-1 LED DRIVE IC901 LC75839PW-US-H LCD CONTROL S[21] 2.6 3 R946 *3 LED944 *1 E D+ 1 4/SHUF S906 D- 3 SEG27 26 SEG28 25 2.6 2 LED942 *1 LED940 *1 27 R954 *3 R924 1.5k 5 R907 R906 27 S905 VBUS-USB R993 1k LED946 *1 LED938 *1 D R950 *3 C904 0.47 IC901 55 SEG2 56 VDD 0.1 4.8 2 R923 1.2k GND 20 2.6 S[47] S904 4 S[2] 2.6 6 2.6 SEG25 28 SEG26 27 C902 R904 1M 5.1 5/ZAP CE ILL(FP+B) 18 PANEL_SW 19 CN902 4P LSW907 COM[1] 53 COM2 54 COM1 S[48] CLK 1 2.6 SEG23 30 SEG24 29 COLOR2 LCD_CE 16 LCD_CLK 17 3 R910 120 Q901 RT1N140C-TP-1 LCD BACK LIGHT DRIVE 0.1 COM[2] 51 COM4 52 COM3 COLOR1 DATA 5 R992 1k 2.6 SEG21 32 SEG22 31 BACK-LIGHT SIRCS 14 LCD_DATA 15 R922 1k 2 2.6 COM[3] 49 SEG4 50 SEG3 NCO S903 SEEK+ 4 2.6 COM[4] 5.1 KEY_1 12 KEY_0 13 (Page 28) 6 R940 *2 RE_0 10 RE_1 11 A 6/PAUSE C903 0.1 2.6 S[3] 5.1 9 R909 120 LSW906 S[4] 5.2 18p AUX_GND 1 R976 0 REMOTE CONTROL SIGNAL RECEIVER 18p 8 3 R908 120 IC902 18p AUX_R R944 *2 R921 1k 5 C906 0.1 C909 7 S902 SOURCE / OFF 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 R903 100 C910 AUX_L R991 820 IC902 PNJ4813M01S0 C911 6 2 D901 DA2J10100L KEY_GND 4 D902 RKZ5.1B2KGP1 5 6 R902 150 LED901 NESW505DT-A0-UV (LCD BACK LIGHT) GND 1 R982 *7 LED932 *1 4 RKZ6.8B2KGP1 D+ RKZ6.8B2KGP1 3 D911 D- 0.1 2 R920 820 3 R980 *7 LED936 *1 SEEK+ C USB_VBUS S901 LSW905 DSPL / SCRL 5 R942 0 D912 MAIN BOARD (3/5) CN102 1 FB903 C912 B USB_GND R905 0 SEEK- CN901 20P LED934 *1 J901 AUX D916 RKZ6.8B2KGP1 FB901 R901 150 R998 1k FB902 13 2.6 11 S[8] 10 2.6 9 S[7] 8 2.6 7 S[6] 6 S[5] 5 2.6 4 2.6 3 2 2.6 1 Note 1: Refer to the servicing notes “NOTE FOR REPLACEMENT OF THE USB CONNECTOR (CN902) AND THE AUX JACK (J901)” on page 4, if replacing CN902 and J901. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 32 32 Note 2: IC901 has been changed in the midway of production. Moreover, the KEY board has been changed simultaneously with it. Before repairing, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 • IC Block Diagrams IC301 TDF8556AJ/N5 (MAIN board (1/5)) TAB 1 2 I2C_SDA OUT-FL– 3 I2C BUS 4 I2C_SCL FL OUT-FL+ 5 6 VP2 OUT-RL– 7 RL 8 P-GND1 OUT-RL+ 9 PROTECTION/ DIAGNOSTIC IN-RR 15 12 IN-FL 14 IN-FR MUTE S-GND 13 10 SVR MUTE IN-RL 11 16 BEEP VP OUT-RR+ 17 RR 18 P-GND3 OUT-RR– 19 20 VP1 OUT-FR+ 21 FR OUT-FR– 23 CHIP DETECT/ DIAGNOSTIC DIAG 25 STANDBY/ MUTE 22 STB TEMPERATURE PROTECTION 24 P-GND4 ENABLE LOGIC 26 RST ANT-REM 27 SWITCH AMP-REM 29 SWITCH 28 CRES 30 REGULATOR SERVO+3.3V 31 MECHA+6V 33 AUDIO+B (8.5V) 32 GND 34 PANEL+B VP 35 REFERENCE VOLTAGE BU+B 37 REGULATOR 36 CBU LOAD DUMP PROTECTION BACK-UP SWITCH 33 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE IC402 MM1836A333NRE (MAIN board (1/5)) 5 VIN 4 VOUT CONT 1 BIAS CURRENT LIMIT VREF GND 2 NC 3 34 THERMAL SHUTDOWN CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 IC1300 OZ539IGN-A1-0-TR (MAIN board (2/5)) 16 VREF BST 1 LX 2 VIN 3 EN_SYS 4 15 RT REFERENCE GENERATOR OCP 14 GNDA S OSCILLATOR S USB_OUT 5 FB_US 6 Q HDR VOUT_SYS(USBIN) FAULT PROTECTION VS SEL 2V UVLS 13 SS_SYS 12 EN_USB ADJ GENERATOR CHARGE PUMP OVER-CURRENT OVER-CURRENT LIMIT LIMIT 10 ISET_USB USB FAULT OVER-CURRENT PROTECTION LIMIT 9 FLT_USB 8 VOUT IC681 NJM2878F3-15 (TE2) (MAIN board (5/5)) VDD 5 4 THERMAL PROTECTION 1 2 3 NC BANDGAP REFERENCE GND SYNC 7 CE USB_IN 11 VIC_USB 35 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE IC401 BD3467FV-E2 (MAIN board (3/5)) FADER BOOST FADER ATT FADER BOOST NCO 3 NCO 4 FADER BOOST ISO GND AMP TU_RCH 7 AUX_LCH 8 ISO GND AMP ISO GND AMP AUX_GND 9 AUX_RCH 10 XM_LCH 11 ISO GND AMP ISO GND AMP XM_GND 12 XM_RCH 13 INPUT SELECTOR (2 SINGLE-END AND 4 STEREO ISO) TU_GND 6 INPUT GAIN TU_LCH 5 FADER BOOST FADER BOOST 39 AU_OUT_SR FADER ATT 38 AU_OUT_RL FADER ATT + FADER ATT + 37 AU_OUT_RR 36 AU_OUT_FL FADER ATT 35 AU_OUT_FR 34 AU_IN_FR 33 AU_IN_FL MAIN GAIN ADJUST BUS_RCH 2 40 AU_OUT_SL MUTE FADER ATT 2ND ORDER LOW-PASS FILTER BUS_LCH 1 FADER BOOST 32 AU_IN_RR ISO GND AMP 31 AU_IN_RL FP1 14 FN1 15 FN2 16 30 AU_IN_SUB SUB GAIN ADJUST ISO GND AMP 29 NCO ISO GND AMP FP2 17 28 AU_OUT_LCH 27 AU_OUT_RCH NCO 18 VCC NCO 19 26 VCC (8.5V) 25 FIL 24 GND NCO 20 I2C BUS LOGIC 36 23 I2C_SDA 22 I2C_SCL 21 MUTE CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 • IC Pin Function Description MAIN BOARD (2/5) IC501 R5F3650KBDZ78FA (SYSTEM CONTROL) (Former type) MAIN BOARD (2/5) IC501 R5F3650KBDZ75FA (SYSTEM CONTROL) (New type) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 Pin Name LCD_SO LCD_CLK NOSE_SW SIRCS UNISO UNISI UNISCK BYTE CNVSS XIN XOUT RESET OSCOUT VSS OSCIN VCC1 NMI RC_IN1 BUIN SYSRST BUS_ON MC_RX DOOR_SW MC_TX DOOR_ING SYNC_OUT EJECT_OK BEEP I2C_SCL I2C_SDA FW_TXD FW_RXD FW_CLK FW_BUSY XM_TX XM_RX XM_POWER EN CD_ON CDM_ON WAKE_UP EPM Z_MUTE R/S SW_SEL EQ_TYPE__SEL INITCOL_SEL CE HIT2_SDA HIT2_SCL HIT2_RESET EN_USB VBUS_ON FLT_USB EN_SYS IPOD I/O O O I I O I O I I I O I O ― I ― I I I O O I O O O O O O O I/O O I I O O O O I I O O I O O O O I/O O O O I I O O Description Serial data output for LCD driver Serial clock signal output for LCD driver Front panel detach/attach detect input “L”: With panel, “H”: Without panel Remote control signal (infrared) input SONY BUS serial data output SONY BUS serial data input SONY BUS serial clock signal output External data bus width select signal input (Connect to VSS in this set) Flash writer IF (CNVSS) signal input (L: normally operation, H: flash write) Low speed operation clock signal input (32.768 kHz) Low speed operation clock signal output (32.768 kHz) System reset signal input High speed operation clock signal output (7.92 MHz) Ground terminal High speed operation clock signal input (7.92 MHz) Power supply terminal (+3.3 V) Non-maskable interrupt signal input (Fixed at H in this set) Rotary commander shift key signal input Backup power supply detect signal input System reset signal output VBUS power control signal output MC-BUS communication MECHA (MG-101CA) TX signal input Not used. (Open) MC-BUS communication MECHA (MG-101CA) RX signal output Not used. (Open) DD converter frequency control signal output Not used. (Open) Beep signal output for the power amplifier IC IIC communication serial clock signal output IIC communication serial data input/output Flash writer IF (serial data) output Flash writer IF (serial data) input Flash writer IF (serial clock) signal input Flash writer IF (busy) signal output Not used. (Open) Not used. Not used. CD mechanism servo power supply control request signal input CD mechanism deck power supply control request signal input CD mechanism deck micon wake up signal output EPM signal output (Fixed at L in this set) Z mute signal input Not used. (Open) Not used. (Open) Not used. (Open) CE signal output (Fixed at H in this set) Tuner serial data input/output Tuner serial clock output Tuner reset signal output USB over current detect IC control signal output VBUS power supply control signal input (L: VBUS OFF, H: VBUS ON) USB over current detect signal input Power control DC/DC signal output iPod connection mode signal output Note: Refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7 for New/Former types of IC501. 37 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Pin No. Pin Name I/O 55 EXTATT_XEN O 56 57 58 59 60 TELATT ACC_IN ATT DIAG AMPSTB I I O I O 61 CYRIL_SEL I 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79, 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 VCC2 F_AUX_ATT VSS ILLUMI SEL COLSW SEL BT_MUTE B-OUT SEL AREASEL3 AREASEL2 AREASEL1 AREASEL0 MODELNAME_SEL0 MODELNAME_SEL1 MODELNAME_SEL2 MODELNAME_SEL3 BT_TX BT_RX DEBUG_1, DEBUG_2 RE-IN1 RE-IN0 ILL_IN BT_RTS BT_CTS BT_RESET BT_POWER BT_MIC_DET SA_DATA SA_CLK KEYACK0 KEYACK1 BT_MIC_ON KEYIN1 KEYIN0 AVSS RC_IN0 AVRH AVDD LCD_CE ― O ― I I O I I I I I O O O O O O O I I O O O O O O I O I I O I I ― I ― ― O 38 Description External mute control signal output “L”: CD or USB source is selected, “H”: Other source is selected Telephone attenuator detect signal input (Fixed at L in this set) Accessory power supply detect signal input Audio mute control signal output Condition signal input from power amp IC Standby signal output for power regulator IC Cyril correspondance discrimination signal input (L: No correspondance) (Fixed at L in this set) Power supply terminal (+3.3 V) Not used. (Open) Ground terminal Key illumination voltage setting signal input Not used. (Open) Key illumination color change function signal input Not used. (Open) Not used. (Open) Black out function setting signal input (L: without black out function) Not used. (Open) Destination setting pin 3 Not used. (Open) Destination setting pin 2 Not used. (Open) Destination setting pin 1 Not used. (Open) Destination setting pin 0 Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Rotary encoder signal input 1 Rotary encoder signal input 0 Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Mechnism serial data input Mechnism serial clock output Key acknowledge detect signal input (Rotary commander) Key acknowledge detect signal input (Front panel) Not used. (Open) Key signal input 1 Key signal input 0 Ground terminal for A/D converter Rotary commander key signal input A/D converter external reference power supply terminal (+3.3 V) A/D converter power supply terminal (+3.3 V) Chip enable signal output for LCD driver CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE MAIN BOARD (4/5) IC701 TC94A99FG-003 (SY) (DIGITAL SIGNAL PROCESSOR) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 to 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Pin Name LPFO PVREF VCOF RVSS3 VCOI RVDD3 SLCO RFI RFRPI RFEQO DCOFC AGCI RFO RVSS3 FNI2 FNI1 FPI2 FPI1 VDD1-1 TPI TNI VRO AVSS3 MDI LDO FSMONIT RFZI RFRP TEI AVDD3 FOO TRO VSS-1 FMO DMO VDDM1 /SRAMSTB VDD1-2 VDD3-1 CD-MON2/PIO10 CD-MON3/PIO11 PIO12/DT/BT_DATAi PIO13/DT/BT_BCKi PIO14/DT/BT_LRCKi PIO15/SDo0 to PIO17/SDo2 PIO18/LRCKo PIO19/BCKo PIO20/CKo DVDD12 DAO1 (R_R-CH) DVSS12 DAO2 (F_R-CH) DVREF DVDD34 DAO3 (F_L-CH) DVSS34 DAO4 (R_L-CH) DVDD5 I/O O I O ― I ― O I I O O I O ― I I I I ― I I O ― I O ― I O I ― O O ― O O ― I ― ― ― ― ― ― ― Description Signal output from the operation amplifier for PLL loop filter Reference voltage (+1.65V) input terminal Terminal for VCO filter Ground terminal DSP VCO control voltage input terminal Power supply terminal (+3.3V) EFM slice level output terminal RF signal input terminal RF ripple signal input terminal EFM slice level output terminal DCOFC signal output RF signal amplitude adjustment amplification input terminal RF signal generation amplification output terminal Ground terminal Main beam input terminal (Connect with pin diode C) Main beam input terminal (Connect with pin diode A) Main beam input terminal (Connect with pin diode D) Main beam input terminal (Connect with pin diode B) Power supply terminal (+1.5V) Sub beam amplification input terminal (Connect with pin diode F) Sub beam amplification input terminal (Connect with pin diode E) Reference voltage (+1.65V) output terminal Ground terminal Monitor photo diode amplification input terminal Laser diode amplification output terminal Not used. (Open) RF ripple zero crossing signal input terminal RF ripple signal output terminal Tracking error signal input terminal Power supply terminal (+3.3V) Focus servo equalizer signal output terminal Tracking servo equalizer signal output terminal Ground terminal Feeding servo equalizer signal output terminal Disc servo equalizer signal output terminal Power supply terminal (+1.5V) Strobe signal input from the USB controller “L”: standby mode Power supply terminal (+1.5V) Power supply terminal (+3.3V) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) ― Not used. (Open) ― ― ― ― O ― O ― ― O ― O ― Not used. (Open) Not used. (Open) Not used. (Open) Power supply terminal (+3.3V) R_R channel data output terminal Ground terminal F_R channel data output terminal Reference voltage input terminal Power supply terminal (+3.3V) F_L channel data output terminal Ground terminal R_L channel data output terminal Power supply terminal (+3.3V) 39 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Pin No. 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 40 Pin Name DAO5 (SUB-CH) DVSS5 VDD1-3 VSS-2 XVSS3 XI XO XVDD3 ADVDD3 ADIN1 (IN_L-CH) ADVREFL ADVCM ADVREFH ADIN2 (IN_R-CH) ADVSS3 MS BUS0 BUS1 BUS2/So BUS3/Si BUCK/SCL /CCE VDD3-2 VSS-3 /RST VDD1-4 DEC_REQ BSIF-REQ BSIF-GATE BSIF_DATA BSIF_BCK BSIF_LRCK DEC_XMUTE ZDET CD MON0/SP_DATA CD MON1/SP_CLK TEST PDO TMAX LPFN I/O O ― ― ― ― I O ― ― I O O O I ― I I/O I/O O I I I ― ― I ― O O I I I I I O O I I O O I Description SUB channel data output terminal Ground terminal Power supply terminal (+1.5V) Ground terminal Ground terminal System clock input terminal (16.9344 MHz) System clock output terminal (16.9344 MHz) Power supply terminal (+3.3V) Power supply terminal (+3.3V) Audio signal input terminal (L channel) Reference voltage output terminal Reference voltage output terminal Reference voltage output terminal Audio signal input terminal (R channel) Ground terminal I/F mode selection signal input terminal Fixed at “L” in this set Bus data input/output with the USB controller Bus data input/output with the USB controller Serial data output to the USB controller Serial data input from the USB controller Bus clock signal input from the USB controller Chip enable signal input from the USB controller Power supply terminal (+3.3V) Ground terminal Reset signal input from the system controller Power supply terminal (+1.5V) Request signal output to the USB controller Request signal output to the USB controller Gate signal input from the USB controller Audio data input from the USB controller Bit clock signal input from the USB controller L/R sampling clock signal (44.1 kHz) input terminal for audio data input Muting on/off control signal input from the USB controller Zero detection signal output terminal Spectrum analyzer data output to the USB controller Spectrum analyzer data transfer clock signal input from the USB controller Setting terminal for test mode Normally fixed at “L” Phase error margin signal between EFM signal and PLCK signal output terminal TMAX detection result output terminal Inverted signal input from the operation amplifier for PLL loop filter CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 MAIN BOARD (5/5) IC601 M321FEFG-7KN3 (SY (USB CONTROL) Pin No. 1 2 3 4 5 6 7 8 9 to 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30,31 32 33 34 35 36 37 38 39 40 41 42,43 44 45 46 47 48 49 50 51 52 53 54 55 56 57,58 59 60 61 62 63 64 Pin Name AVSS VREFH RESET MODE OPEN REQ EJECT OK NC WAKE UP NC BU_IN DVSS NC CD_ZDET DEC_XMUTE DEC_LRCK DEC_BCK DEC_DATA DEC_GATE DEC_REQ CD_SO CD_SI CD_SCLK MEC_SELFSW NC DEC_INT CD_XRST CD_XCCE NC Z/Y_CHECK DVCC3 DVSS DRV_ON MEC_LOAD MEC_EJECT MEC_SSTBY MEC_LIMIT MEC_INSW MEC_DSW NC XLINE XINTIO FE/SBAD_SEL Z/Y_SEL NC MECON_CHECK CDON_CHECK A_ATT MECON CDON ZMUTE TXD RXD NC DVCC3 DVSS SWDIO SWCLK TRACECLK TRACEDATA0 I/O ― ― I I O I ― I ― I ― ― I O O O O O I O I O I ― I O O ― ― ― ― O O O O I I I ― ― ― ― ― ― I I O O O O O I ― ― ― I/O I/O ― ― Description Ground terminal for A/D converter Reference power supply terminal for A/D converter Reset signal input Mode signal input Not used. (Open) Front panel open eject signal input Not used. (Open) Wake up request signal input Not used. (Open) Back up signal input Ground terminal Not used. (Open) Zero detection signal input Muting on/off control signal output L/R sampling clock signal(44.1kHz) output Bit clock signal output Audio data signal output Gate signal output Request signal input Serial data output Serial data input Serial clock output Mechanism self switch signal input Not used. (Open) Request signal input CD reset signal output Chip enable signal output Not used. (Open) Not used. (Open) Power supply terminal Ground terminal Motor drive on/off control signal output Mechanism loading signal output(Load) Mechanism eject signal output(Eject) Strobe standby signal output Mechanism deck sled limit in detection signal input Mechanism deck pack in detection signal input Mechanism deck chacking end detection signal input Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Not used. (Open) Mechanism on/off check signal input CD on/off check signal input Audio attenuation signal output Mechanism power supply (+6V) control signal output CD power supply (+3.3V) control signal output Zero mute signal output Mechanism TX signal output Mechanism RX signal input Not used. (Open) Power supply terminal Ground terminal Flash write SWDIO signal input/output Flash write SWCLK signal input/output Not used. (Open) Not used. (Open) 41 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Pin No. 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88,89 90,91 92 93 to 100 42 Pin Name TRACEDATA1 TRACEDATA2 TRACEDATA3 CP_SDA CP_SCL NC CP_RESET CPON CDON_15V VBUS_ON NC REGVCC3 XT1 XT2 CVCC3 X1 CVSS X2 DVCC3 DVSS USB+ USBNMI TEST NC AVCC3 NC I/O ― ― ― I/O O ― O O O O ― ― ― ― ― I ― O ― ― I/O I/O I ― ― ― ― Description Not used. (Open) Not used. (Open) Not used. (Open) CP serial data input/output CP serial clock output Not used. (Open) CP reset signal output CP power supply control signal output Servo power supply (+1.5V) control signal output USB VBUS control signal output Not used. (Open) Power supply terminal Not used. (Fixed at L.) Not used. (Open) Power supply terminal System clock input terminal(12MHz) Ground terminal System clock input terminal(12MHz) Power supply terminal Ground terminal USB serial data input/output + USB serial data input/output Non-maskable interrupt signal input(Fixed at H). Not used. (Open) Not used. (Open) Power supply terminal Not used. (Open) CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 SECTION 5 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. 5-1. MAIN SECTION KR MX RU • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet’s Color • Accessories are given in the last of the electrical parts list. • Abbreviation AR : Argentina model CND : Canadian model EA : Saudi Arabia model IND : Indian model : Korean model : Mexican model : Russian model The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 6 #3 #1 not supplied #5 5 FU601 #4 #5 #4 A 4 #3 not supplied #2 not supplied CD mechanism section (MG-101CA-188) #2 TU901 MAIN board B A #1 3 not supplied B #1 2 #1 not supplied front panel section not supplied #1 1 Note 1: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5. Ref. No. 1 2 3 4 5 Part No. Description X-2581-176-3 3-042-244-11 X-2547-583-3 4-410-504-01 A-1831-756-A PANEL ASSY, SUB SCREW (T) LOCK ASSY (T) SCREW (+PTT 2.6X6), GROUND POINT MAIN BOARD, COMPLETE (EXCEPT AEP, RU, UK, EA) (Former type) Remark 5 A-1831-756-B 5 5 5 5 A-1831-772-A A-1831-772-B A-1832-546-A A-1832-546-B MAIN BOARD, COMPLETE (EXCEPT AEP, RU, UK, EA) (New type) MAIN BOARD, COMPLETE (AEP, UK) (Former type) MAIN BOARD, COMPLETE (AEP, UK) (New type) MAIN BOARD, COMPLETE (RU) (Former type) MAIN BOARD, COMPLETE (RU) (New type) 5 A-1851-887-A MAIN BOARD, COMPLETE (EA) (Former type) Note 2: COMPLETE MAIN BOARD (Ref. No. 5) has been changed in the midway of production. When COMPLETE MAIN BOARD (Ref. No. 5) is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. Ref. No. Part No. Description 5 6 A-1851-887-B 1-839-372-11 6 1-839-387-11 FU601 1-532-877-11 MAIN BOARD, COMPLETE (EA) (New type) CONNECTION CORD FOR AUTOMOBILE (POWER) (US, CND, E, EA, MX, KR, IND) CONNECTION CODE (ISO) (POWER) (AEP, RU, UK, AR) FUSE (BLADE TYPE) (AUTO FUSE) (10 A/32 V) Remark TU901 #1 #2 #3 #4 A-1878-198-A 7-685-792-09 7-685-790-01 7-685-793-01 7-685-794-01 TUX-DSP02 (TUNER UNIT) SCREW +PTT 2.6X6 (S) SCREW +PTT 2.6X4 (S) SCREW +PTT 2.6X8 (S) SCREW +PTT 2.6X10 (S) #5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 43 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 5-2. FRONT PANEL SECTION 66 64 63 not supplied (KEY board) RE901 not supplied 64 IC902 61 62 65 LCD901 not supplied CN902 55 54 J901 53 52 60 59 51 58 57 56 Note 1: FRONT PANEL OVERALL ASSY (Ref. No. 66) has been changed in the midway of production. When FRONT PANEL OVERALL ASSY (Ref. No. 66) is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. Ref. No. Part No. Description Part No. Description 51 52 52 53 54 4-183-276-01 4-183-275-03 4-183-275-13 4-183-273-11 4-183-274-01 BUTTON (EJECT) BUTTON (PRESET) (AEP, RU, UK) BUTTON (PRESET) (EXCEPT AEP, RU, UK) BUTTON (EQ3) BUTTON (RELEASE) 66 A-1831-789-A 66 A-1831-789-B 66 A-1831-795-A 55 56 56 57 58 2-639-881-01 X-2581-888-1 X-2581-889-1 X-2581-858-1 4-183-271-02 SPRING (RELEASE) PANEL (SV) ASSY, FRONT (GT40U: US, CND) PANEL (SV) ASSY, FRONT (GT40UW) KNOB (VOL) (SV) ASSY BUTTON (MODE) 66 A-1831-795-B 66 A-1831-800-A PANEL OVERALL ASSY, FRONT (GT44U: IND) (Former type) PANEL OVERALL ASSY, FRONT (GT44U: IND) (New type) PANEL OVERALL ASSY, FRONT (GT44U: AEP, UK) (Former type) PANEL OVERALL ASSY, FRONT (GT44U: AEP, UK) (New type) PANEL OVERALL ASSY, FRONT (GT47UE) (Former type) 66 A-1831-800-B 59 60 61 62 63 4-183-272-31 4-183-270-02 1-780-968-11 4-278-080-01 4-279-394-01 BUTTON (BACK) BUTTON (SOURCE) CONDUCTIVE BOARD, CONNECTION ILLUMINATOR (LCD) PANEL, BACK 66 A-1835-141-A 66 A-1835-141-B 66 A-1837-401-A 64 65 3-250-543-21 X-2187-544-5 66 A-1837-401-B 66 A-1831-758-A 66 A-1847-849-A 66 A-1831-758-B 66 A-1847-849-B 66 A-1831-765-A SCREW (+B P-TITE M2) CASE ASSY (for FRONT PANEL) (GT42UE/GT44U: IND/GT45U) PANEL OVERALL ASSY, FRONT (GT40U: US, CND) (Former type) PANEL OVERALL ASSY, FRONT (GT40U: US, CND) (New type) PANEL OVERALL ASSY, FRONT (GT40UW) (Former type) 66 A-1850-669-A 66 A-1850-669-B CN902 1-822-798-11 PANEL OVERALL ASSY, FRONT (GT45U: MX) (Former type) PANEL OVERALL ASSY, FRONT (GT45U: MX) (New type) PANEL OVERALL ASSY, FRONT (GT45U: KR) (Former type) PANEL OVERALL ASSY, FRONT (GT45U: KR) (New type) USB CONNECTOR (USB) IC902 J901 LCD901 RE901 6-600-806-01 1-822-148-11 1-811-224-11 1-487-023-22 IC PNJ4813M01S0 SMALL TYPE JACK (VERTICAL) (AUX) DISPLAY PANEL, LIQUID CRYSTAL ROTARY ENCODER (PUSH SELECT (VOLUME)) 66 A-1831-765-B 66 A-1831-774-A 66 A-1831-774-B 66 A-1831-783-A 66 A-1831-783-B 44 Remark PANEL OVERALL ASSY, FRONT (GT40UW) (New type) PANEL OVERALL ASSY, FRONT (GT40U: RU) (Former type) PANEL OVERALL ASSY, FRONT (GT40U: RU) (New type) PANEL OVERALL ASSY, FRONT (GT45U: E, EA, AR) (Former type) PANEL OVERALL ASSY, FRONT (GT45U: E, EA, AR) (New type) Ref. No. Note 2: Refer to the servicing notes “NOTE FOR REPLACEMENT OF THE USB CONNECTOR (CN902) AND THE AUX JACK (J901)” on page 4, if replacing CN902 and J901. Remark PANEL OVERALL ASSY, FRONT (GT47UE) (New type) PANEL OVERALL ASSY, FRONT (GT40U: AEP, UK) (Former type) PANEL OVERALL ASSY, FRONT (GT40U: AEP, UK) (New type) PANEL OVERALL ASSY, FRONT (GT42UE) (Former type) PANEL OVERALL ASSY, FRONT (GT42UE) (New type) CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 5-3. CD MECHANISM SECTION (MG-101CA-188) 101 102 not supplied not supplied 108 103 108 105 not supplied not supplied not supplied not supplied not supplied SENSOR board 104 not supplied not supplied not supplied not supplied not supplied 107 106 106 Note: As for the mechanism deck (MG-101CA-188) carried in this unit, component parts have been changed from the midway of production. When you perform repair exchange of the mechanism deck (MG-101CA-188), refer to “ABOUT THE MG-101CA-188 OF FORMER AND NEW” on page 6. Ref. No. 101 101 0 102 0 103 104 Part No. Description Remark A-1313-179-A A-1866-801-A A-1284-705-A X-2149-672-1 2-626-869-31 MECHANICAL BLOCK (Z) ASSY 08 (Former type) MECHANICAL BLOCK (11CA) ASSY (New type) DAXEV08//Q SERVICE ASSY, OP (DAX-25A) SCREW (M2X3), SERRATION Ref. No. 105 106 107 107 108 Part No. Description Remark 3-686-458-21 3-352-758-31 A-1823-723-A A-1866-089-A 2-134-636-71 SCREW (P1.4), TAPPING SCREW (M1.7X2.5), TOOTHED LOCK SERVO BOARD, COMPLETE (Former type) SERVO BOARD, COMPLETE (New type) SCREW (M1.7X2.5) 45 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 SECTION 6 KEY ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable Ref. No. Part No. RU • CAPACITORS uF: μF • COILS uH: μH • SEMICONDUCTORS In each case, u: μ, for example: uA. . : μA. . , uPA. . , μPA. . , uPB. . : μPB. . , uPC. . , μPC. . , uPD. . : μPD. . • Abbreviation AR : Argentina model CND : Canadian model EA : SaudI Arabia model IND : Indian model KR : Korean model MX : Mexican model Description Remark KEY BOARD ********** Ref. No. : Russian model When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Part No. Description LED936 6-502-325-11 LED938 6-502-193-11 LED938 6-502-325-11 LED940 6-502-193-11 LED SML-D12P8WT86TK (SEEK+ > M) (AEP, RU, UK) LED SML-D12V8WT86TN (ILLUMINATION) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (ILLUMINATION) (AEP, RU, UK) LED SML-D12V8WT86TN (ILLUMINATION) (EXCEPT AEP, RU, UK) LED940 6-502-325-11 < CAPACITOR > C901 C902 C903 C904 C906 1-100-597-91 1-100-597-91 1-100-597-91 1-125-891-11 1-100-597-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.47uF 0.1uF 10% 10% 10% 10% 10% 25V 25V 25V 10V 25V C909 C910 C911 C912 C915 1-162-918-11 1-162-918-11 1-162-918-11 1-100-597-91 1-162-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 18PF 18PF 18PF 0.1uF 0.001uF 5% 5% 5% 10% 10% 50V 50V 50V 25V 50V LED942 6-502-193-11 LED942 6-502-325-11 LED944 6-502-193-11 C916 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V LED944 6-502-325-11 LED946 6-502-193-11 LED946 LED950 6-502-325-11 6-502-193-11 LED950 6-502-325-11 LED952 6-502-193-11 LED952 LED954 6-502-325-11 6-502-193-11 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD LED954 6-502-325-11 < IC > LSW905 1-798-283-11 IC LC75839PW-US-H LSW905 1-798-287-11 < LED > LSW906 1-798-283-11 LED NESW505DT-A0-UV (LCD BACK LIGHT) LED SML-D12V8WT86TN ( ) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK ( ) (AEP, RU, UK) LED SML-D12V8WT86TN (m . SEEK –) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (m . SEEK –) (AEP, RU, UK) LSW906 1-798-287-11 LED SML-D12V8WT86TN (SEEK+ > M) (EXCEPT AEP, RU, UK) LSW908 1-798-287-11 Remark LED SML-D12P8WT86TK (ILLUMINATION) (AEP, RU, UK) LED SML-D12V8WT86TN (ILLUMINATION) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (ILLUMINATION) (AEP, RU, UK) LED SML-D12V8WT86TN (ILLUMINATION) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (ILLUMINATION) (AEP, RU, UK) < CONNECTOR > CN901 1-842-265-22 PLUG, CONNECTOR 20P < DIODE > D901 D902 D911 D912 D916 6-502-961-01 6-503-202-01 6-503-205-01 6-503-205-01 6-503-205-01 DIODE DIODE DIODE DIODE DIODE DA2J10100L RKZ5.1B2KGP1 RKZ6.8B2KGP1 RKZ6.8B2KGP1 RKZ6.8B2KGP1 < FERRITE BEAD > FB901 FB902 FB903 IC901 1-414-385-21 1-414-385-21 1-414-385-21 6-717-496-01 LED901 LED932 6-503-227-01 6-502-193-11 LED932 LED934 6-502-325-11 6-502-193-11 LED934 6-502-325-11 LED936 6-502-193-11 LED SML-D12P8WT86TK (MODE) (AEP, RU, UK) LED SML-D12V8WT86TN ( ) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK ( ) (AEP, RU, UK) < SWITCH > LSW907 1-798-283-11 LSW907 1-798-287-11 LSW908 1-798-283-11 Note: IC901 has been changed in the midway of production. Moreover, the KEY board has been changed simultaneously with it. Before repairing, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. 46 LED SML-D12V8WT86TN (Z) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (Z) (AEP, RU, UK) LED SML-D12V8WT86TN (SOURCE/OFF) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (SOURCE/OFF) (AEP, RU, UK) LED SML-D12V8WT86TN (MODE) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (DSPL/SCRL) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (DSPL/SCRL) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (6/PAUSE) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (6/PAUSE) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (5/ZAP) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (5/ZAP) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (4/SHUF) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (4/SHUF) (EXCEPT AEP, RU, UK) CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.2 KEY Ref. No. Part No. LSW909 1-798-283-11 LSW909 1-798-287-11 LSW910 1-798-283-11 LSW910 1-798-287-11 LSW911 1-798-283-11 LSW911 1-798-287-11 LSW912 1-798-283-11 LSW912 1-798-287-11 Description Remark TACTILE SWITCH (WITH LED) (3/REP) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (3/REP) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (2/ALBUM v) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (2/ALBUM v) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (1/ALBUM V) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (1/ALBUM V) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (AF/TA/PTY) (AEP, RU, UK) Ref. No. Part No. Description R950 1-216-814-11 METAL CHIP 270 Remark R950 1-216-821-11 METAL CHIP 1K R952 1-216-815-11 METAL CHIP 330 R952 1-216-822-11 METAL CHIP 1.2K R954 1-216-814-11 METAL CHIP 270 R954 1-216-821-11 METAL CHIP 1K R956 1-216-814-11 METAL CHIP 270 R956 1-216-821-11 METAL CHIP 1K R958 1-216-814-11 METAL CHIP 270 R958 1-216-822-11 METAL CHIP 1.2K R966 1-216-815-11 METAL CHIP 330 R966 1-216-821-11 METAL CHIP 1K R968 1-216-815-11 METAL CHIP 330 R968 1-216-822-11 METAL CHIP 1.2K R970 1-216-814-11 METAL CHIP 270 R970 1-216-821-11 METAL CHIP 1K R972 1-216-814-11 METAL CHIP 270 R972 1-216-821-11 METAL CHIP 1K R974 1-216-814-11 METAL CHIP 270 R974 1-216-822-11 METAL CHIP 1.2K TACTILE SWITCH (WITH LED) (PTY) (EXCEPT AEP, RU, UK) < TRANSISTOR > Q901 Q903 8-729-038-22 6-551-392-01 TRANSISTOR TRANSISTOR RT1N140C-TP-1 RT6N140C-TP-1 < RESISTOR > R901 R902 R903 R904 R905 1-216-811-11 1-216-811-11 1-216-809-11 1-216-857-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 150 150 100 1M 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R906 R907 R908 R909 R910 1-216-802-11 1-216-802-11 1-216-810-11 1-216-810-11 1-216-810-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 27 27 120 120 120 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R915 R916 R917 R918 R919 1-216-817-11 1-216-817-11 1-216-817-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP 470 470 470 0 0 5% 5% 5% 1/10W 1/10W 1/10W R920 R921 R922 R923 R924 1-216-820-11 1-216-821-11 1-216-821-11 1-216-822-11 1-216-823-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 820 1K 1K 1.2K 1.5K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R976 R980 1-216-864-11 1-216-809-11 SHORT CHIP METAL CHIP 0 100 R980 1-216-811-11 METAL CHIP 150 R925 R926 R927 R940 1-216-824-11 1-216-825-11 1-216-295-91 1-216-813-11 METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 1.8K 2.2K 0 220 5% 5% 1/10W 1/10W R982 1-216-809-11 METAL CHIP 100 R982 1-216-811-11 METAL CHIP 150 R984 1-216-809-11 METAL CHIP 100 R940 1-216-820-11 METAL CHIP 820 R984 1-216-811-11 METAL CHIP 150 R986 1-216-809-11 METAL CHIP 100 R986 1-216-811-11 METAL CHIP 150 R988 1-216-811-11 METAL CHIP 150 R988 1-216-813-11 METAL CHIP 220 R990 1-216-812-11 METAL CHIP 180 R990 1-216-813-11 METAL CHIP 220 R942 R944 1-216-864-11 1-216-813-11 SHORT CHIP METAL CHIP 0 220 R944 1-216-820-11 METAL CHIP 820 R946 1-216-814-11 METAL CHIP 270 R946 1-216-821-11 METAL CHIP 1K R948 1-216-815-11 METAL CHIP 330 R948 1-216-822-11 METAL CHIP 1.2K 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 47 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 KEY MAIN Ref. No. Part No. Description R991 R992 R993 R994 R995 1-216-820-11 1-216-821-11 1-216-821-11 1-216-822-11 1-216-823-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 820 1K 1K 1.2K 1.5K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W Remark R996 R997 R998 R999 1-216-824-11 1-216-825-11 1-216-821-11 1-216-295-91 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 1.8K 2.2K 1K 0 5% 5% 5% 1/10W 1/10W 1/10W < SWITCH > S901 S902 S903 S904 S905 1-798-284-11 1-798-284-11 1-798-284-11 1-798-284-11 1-798-284-11 TACTILE SWITCH (Z) TACTILE SWITCH (SOURCE/OFF) TACTILE SWITCH (SEEK+ > M) TACTILE SWITCH ( ) TACTILE SWITCH (m . SEEK –) S906 1-798-284-11 TACTILE SWITCH ( ) S907 1-798-284-11 TACTILE SWITCH (MODE) ************************************************************* A-1831-756-A A-1831-756-B A-1831-772-A A-1831-772-B A-1832-546-A MAIN BOARD, COMPLETE (EXCEPT AEP, RU, UK, EA) (Former type) MAIN BOARD, COMPLETE (EXCEPT AEP, RU, UK, EA) (New type) MAIN BOARD, COMPLETE (AEP, UK) (Former type) MAIN BOARD, COMPLETE (AEP, UK) (New type) MAIN BOARD, COMPLETE (RU) (Former type) Part No. Description C331 C334 C335 C398 1-116-739-11 1-118-067-11 1-114-868-11 1-100-905-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 0.47uF 3300uF 0.1uF 0.001uF 10% 20% 10% 10% 50V 16V 50V 50V Remark C399 C401 C402 C403 C407 1-100-591-91 1-114-582-91 1-165-908-11 1-100-354-21 1-100-597-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 1uF 0.1uF 1uF 220uF 0.1uF 10% 10% 10% 20% 10% 25V 16V 10V 6.3V 25V C409 C410 C411 C413 C414 1-100-588-21 1-124-779-00 1-100-354-21 1-124-779-00 1-100-597-91 ELECT CHIP ELECT CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP 1000uF 10uF 220uF 10uF 0.1uF 20% 20% 20% 20% 10% 6.3V 16V 6.3V 16V 25V C415 C416 C419 C420 C422 1-128-398-11 1-128-992-21 1-124-779-00 1-124-779-00 1-124-779-00 ELECT CHIP ELECT CHIP ELECT CHIP ELECT CHIP ELECT CHIP 220uF 47uF 10uF 10uF 10uF 20% 20% 20% 20% 20% 16V 25V 16V 16V 16V C424 C425 C436 C437 C438 1-124-779-00 1-124-779-00 1-165-908-11 1-165-908-11 1-112-064-11 ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 10uF 1uF 1uF 2.2uF 20% 20% 10% 10% 10% 16V 16V 10V 10V 10V C439 C440 C442 C457 C501 1-162-964-11 1-162-964-11 1-100-597-91 1-162-970-11 1-162-923-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.1uF 0.01uF 47PF 10% 10% 10% 10% 5% 10% 5% 50V 50V 25V 25V 50V (EXCEPT EA) A-1832-546-B A-1851-887-A A-1851-887-B MAIN BOARD, COMPLETE (RU) (New type) MAIN BOARD, COMPLETE (EA) (Former type) MAIN BOARD, COMPLETE (EA) (New type) ********************* 7-685-134-19 7-685-794-01 SCREW +P 2.6X8 TYPE2 NON-SLIT SCREW +PTT 2.6X10 (S) C502 C503 1-164-937-11 1-162-923-11 CERAMIC CHIP 0.001uF CERAMIC CHIP 47PF < CAPACITOR > C504 C507 C508 1-100-597-91 1-164-858-11 1-164-856-81 CERAMIC CHIP 0.1uF CERAMIC CHIP 22PF CERAMIC CHIP 18PF 50V 50V (EXCEPT EA) 10% 25V 5% 50V 5% 50V C510 C512 C513 C514 C518 1-165-908-11 1-164-937-11 1-162-970-11 1-164-937-11 1-119-923-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 0.001uF 0.01uF 0.001uF 0.047uF 10% 10% 10% 10% 10% 10V 50V 25V 50V 10V C520 C521 C522 C523 C601 1-164-866-11 1-164-866-11 1-100-567-81 1-100-567-81 1-100-597-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47PF 47PF 0.01uF 0.01uF 0.1uF 5% 5% 10% 10% 10% 50V 50V 25V 25V 25V C605 C606 C607 C608 C609 1-100-567-81 1-100-567-81 1-100-567-81 1-114-582-91 1-100-597-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 0.01uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 25V 25V 25V 16V 25V C610 C612 C613 C614 C615 1-162-964-11 1-100-597-91 1-125-777-11 1-164-850-11 1-164-850-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.1uF 0.1uF 10PF 10PF 10% 10% 10% 0.5PF 0.5PF 50V 25V 10V 50V 50V C616 C617 C683 1-125-777-11 1-100-597-91 1-100-597-91 CERAMIC CHIP 0.1uF CERAMIC CHIP 0.1uF CERAMIC CHIP 0.1uF 10% 10% 10% 10V 25V 25V C10 C11 C15 C100 C101 1-100-591-91 1-137-765-21 1-165-908-11 1-114-582-91 1-162-964-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 47uF 1uF 0.1uF 0.001uF 10% 20% 10% 10% 10% 25V 16V 10V 16V 50V C103 C203 C301 C302 C303 1-114-868-11 1-164-937-11 1-127-715-11 1-116-733-11 1-137-893-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.1uF 0.001uF 0.22uF 1uF 22uF 10% 10% 10% 10% 20% 50V 50V 16V 25V 16V C305 C306 C308 C309 C311 1-116-733-11 1-165-908-11 1-127-715-11 1-100-354-21 1-127-715-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 1uF 1uF 0.22uF 220uF 0.22uF 10% 10% 10% 20% 10% 25V 10V 16V 6.3V 16V C312 C313 C314 C315 C317 1-124-779-00 1-137-765-21 1-112-064-11 1-112-780-11 1-112-780-11 ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 47uF 2.2uF 0.47uF 0.47uF 20% 20% 10% 10% 10% 16V 16V 10V 16V 16V C319 C321 C323 C326 C327 1-112-780-11 1-112-780-11 1-164-937-11 1-164-866-11 1-116-733-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.47uF 0.47uF 0.001uF 47PF 1uF 10% 10% 10% 5% 10% 16V 16V 50V 50V 25V C330 1-116-739-11 CERAMIC CHIP 0.47uF 10% 50V Note 1: When the complete MAIN board is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5. 48 Ref. No. Note 2: The complete MAIN board has been changed in the midway of production. When the complete MAIN board is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 MAIN Ref. No. Part No. Description Part No. Description C685 C686 1-164-937-11 1-164-937-11 CERAMIC CHIP 0.001uF CERAMIC CHIP 0.001uF 10% 10% 50V 50V Remark Ref. No. C780 C781 1-164-172-11 1-100-597-91 CERAMIC CHIP 0.0056uF CERAMIC CHIP 0.1uF 10% 10% 25V 25V Remark C687 C688 C689 C690 C701 1-165-908-11 1-165-884-11 1-165-884-11 1-165-908-11 1-100-597-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 2.2uF 2.2uF 1uF 0.1uF 10% 10% 10% 10% 10% 10V 6.3V 6.3V 10V 25V C782 C783 C784 C786 C787 1-114-582-91 1-125-777-11 1-127-988-81 1-114-582-91 1-114-582-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.015uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 10V 16V 16V 16V C711 C712 C713 C714 C715 1-100-597-91 1-126-208-21 1-119-923-11 1-119-923-11 1-164-935-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 47uF 0.047uF 0.047uF 470PF 10% 20% 10% 10% 10% 25V 4V 10V 10V 50V C788 C789 C792 C1301 C1304 1-164-937-11 1-164-939-11 1-125-777-11 1-100-591-91 1-116-705-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.0022uF 0.1uF 1uF 47uF 10% 10% 10% 10% 20% 50V 50V 10V 25V 16V C716 C717 C718 C719 C720 1-162-962-11 1-114-582-91 1-127-772-81 1-100-579-81 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 470PF 0.1uF 0.033uF 0.0056uF 0.1uF 10% 10% 10% 10% 10% 50V 16V 10V 25V 10V C1305 C1306 C1307 C1308 C1309 1-100-055-21 1-164-936-11 1-164-943-81 1-112-064-11 1-114-323-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 22uF 680PF 0.01uF 2.2uF 0.01uF 20% 10% 10% 10% 10% 16V 50V 16V 10V 50V C721 C722 C724 C725 C726 1-114-582-91 1-114-582-91 1-114-582-91 1-124-778-00 1-164-940-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 22uF 0.0033uF 10% 10% 10% 20% 10% 16V 16V 16V 6.3V 16V C1310 C1311 C1312 C1315 C1316 1-114-582-91 1-117-681-11 1-100-567-81 1-100-055-21 1-100-597-91 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 100uF 0.01uF 22uF 0.1uF 10% 20% 10% 20% 10% C727 C728 C729 C730 C732 1-164-940-11 1-164-940-11 1-164-940-11 1-164-940-11 1-164-937-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0033uF 0.0033uF 0.0033uF 0.0033uF 0.001uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 50V C1316 C1317 1-114-246-11 1-162-970-11 CERAMIC CHIP 1uF CERAMIC CHIP 0.01uF 20% 10% C733 C734 C735 C737 C738 1-100-597-91 1-164-860-11 1-114-582-91 1-100-742-91 1-100-742-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 27PF 0.1uF 2.2uF 2.2uF 10% 5% 10% 20% 20% 25V 50V 16V 10V 10V C739 C741 * C742 C743 * C744 1-114-582-91 1-164-878-11 1-116-727-11 1-164-878-11 1-116-727-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 150PF 2.2uF 150PF 2.2uF 10% 5% 10% 5% 10% 16V 50V 16V 50V 16V C745 * C746 C747 C748 C750 1-164-878-11 1-116-727-11 1-164-939-11 1-164-939-11 1-126-603-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 150PF 2.2uF 0.0022uF 0.0022uF 4.7uF 5% 10% 10% 10% 20% 50V 16V 50V 50V 35V C751 C752 C753 C754 C756 1-126-603-11 1-126-603-11 1-126-603-11 1-100-742-91 1-164-937-11 ELECT CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 4.7uF 4.7uF 2.2uF 0.001uF 20% 20% 20% 20% 10% 35V 35V 35V 10V 50V C759 C760 C761 C764 C766 1-100-567-81 1-100-597-91 1-100-597-91 1-164-937-11 1-100-567-81 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.1uF 0.1uF 0.001uF 0.01uF 10% 10% 10% 10% 10% 25V 25V 25V 50V 25V C767 C768 C771 C772 C776 1-125-777-11 1-125-777-11 1-164-866-11 1-127-988-81 1-100-597-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 47PF 0.015uF 0.1uF 10% 10% 5% 10% 10% 10V 10V 50V 16V 25V C777 C778 C779 1-100-567-81 1-125-777-11 1-100-567-81 CERAMIC CHIP 0.01uF CERAMIC CHIP 0.1uF CERAMIC CHIP 0.01uF 10% 10% 10% 25V 10V 25V 16V 16V 25V 16V 25V (EXCEPT EA) 25V (EA) 25V < CONNECTOR > CN102 CN301 CN501 CN601 CN700 1-842-266-22 1-843-352-11 1-779-806-21 1-785-900-21 1-842-487-12 SOCKET, CONNECTOR 20P PIN, CONNECTOR 16P CONNECTOR 8P CONNECTOR 5P CONNECTOR, BOARD TO BOARD 28P < DIODE > D101 D102 D110 D119 D306 6-503-205-01 6-503-205-01 6-503-205-01 6-503-205-01 6-503-238-01 DIODE DIODE DIODE DIODE DIODE RKZ6.8B2KGP1 RKZ6.8B2KGP1 RKZ6.8B2KGP1 RKZ6.8B2KGP1 GN1G (AEP, UK) D318 D320 D321 D323 D324 6-503-238-01 6-503-213-01 6-503-238-01 6-503-213-01 6-503-238-01 DIODE DIODE DIODE DIODE DIODE GN1G RKZ18B2KGP1 GN1G RKZ18B2KGP1 GN1G D401 D403 D530 D731 D805 6-502-961-01 6-500-335-01 6-503-759-01 6-501-013-01 6-503-206-01 DIODE DIODE DIODE DIODE DIODE DA2J10100L MC2838-T112-1 RB751V40, 115 BAT54ALT1G RKZ7.5B2KGP1 D806 D1300 6-503-213-01 6-503-319-01 DIODE RKZ18B2KGP1 DIODE DB2X41400L < FUSE > F4 1-576-415-11 FUSE (2 A/32 V) < FERRITE BEAD/JUMPER RESISTOR > FB19 FB398 FB501 FB610 1-400-334-21 1-469-084-21 1-414-595-11 1-216-864-11 FERRITE, EMI (SMD) (1608) FERRITE INDUCTOR, FERRITE BEAD SHORT CHIP 0 Note: C741, C743, C745, CN501 and CN601 have been deleted in the midway of production. 49 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 MAIN Ref. No. Part No. Description FB611 1-500-113-22 BEAD, FERRITE (CHIP) (1608) Remark FB612 FB694 FB695 FB696 FB698 1-500-113-22 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 BEAD, FERRITE (CHIP) (1608) SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 FB717 FB718 FB719 FB720 FB721 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 FB722 FB724 FB750 FB751 FB760 1-216-864-11 1-469-084-21 1-216-864-11 1-216-864-11 1-216-864-11 SHORT CHIP FERRITE SHORT CHIP SHORT CHIP SHORT CHIP 0 FB762 FB782 FB801 FB802 FB803 1-216-864-11 1-469-084-21 1-500-113-22 1-500-113-22 1-500-113-22 SHORT CHIP 0 FERRITE BEAD, FERRITE (CHIP) (1608) BEAD, FERRITE (CHIP) (1608) BEAD, FERRITE (CHIP) (1608) FB890 FB891 1-500-113-22 1-500-113-22 BEAD, FERRITE (CHIP) (1608) BEAD, FERRITE (CHIP) (1608) 0 0 0 Ref. No. Q801 Q802 Q803 Part No. Description 6-552-444-01 6-552-430-01 8-729-620-13 TRANSISTOR TRANSISTOR TRANSISTOR Remark DRC5144E0L DRC5114E0L 2SC4154TP-1EF < RESISTOR > R10 R11 R12 R13 R19 1-218-990-81 1-216-864-11 1-216-864-11 1-216-821-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP SHORT CHIP 0 0 0 1K 0 R102 R116 R121 R122 R199 1-216-864-11 1-216-295-91 1-216-864-11 1-216-864-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 R300 R301 R302 R303 R304 1-216-296-11 1-218-941-81 1-218-941-81 1-216-182-00 1-216-182-00 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 100 100 220 220 R305 R306 R307 R308 R309 1-216-182-00 1-216-182-00 1-218-943-11 1-216-295-91 1-218-973-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP R311 R312 R313 R314 R340 1-216-073-91 1-218-973-11 1-218-973-11 1-218-961-11 1-216-864-11 R378 R395 R396 R400 R401 5% 1/10W 5% 5% 5% 5% 1/16W 1/16W 1/8W 1/8W 220 220 150 0 47K 5% 5% 5% 1/8W 1/8W 1/16W 5% 1/16W METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 10K 47K 47K 4.7K 0 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1-216-073-91 1-216-296-11 1-216-296-11 1-216-295-91 1-218-977-11 METAL CHIP SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP 10K 0 0 0 100K 5% 1/10W 5% 1/16W R402 R403 R404 R405 R406 1-218-953-11 1-216-833-11 1-218-953-11 1-216-833-11 1-218-990-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 1K 10K 1K 10K 0 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/10W R407 R409 R410 R411 R415 1-218-953-11 1-216-833-11 1-218-953-11 1-216-833-11 1-216-049-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 1K 10K 1K 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/10W 1/10W R416 R417 R418 R419 R420 1-216-049-11 1-216-834-11 1-216-834-11 1-216-825-11 1-216-295-91 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 1K 12K 12K 2.2K 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W < IC > IC301 IC401 IC402 IC403 IC501 6-715-848-21 6-714-623-01 6-716-993-01 6-712-776-01 6-717-897-02 IC IC IC IC IC TDF8556AJ/N5 BD3467FV-E2 MM1836A33NRE PST8228UL R5F3650KBDZ78FA (Former type) IC501 IC601 IC681 IC682 IC701 6-718-646-01 6-718-962-01 6-711-238-01 6-711-238-01 6-715-712-01 IC IC IC IC IC R5F3650KBDZ75FA (New type) M321FEFG-7KN3 (SY NJM2878F3-15 (TE2) NJM2878F3-15 (TE2) TC94A99FG-003 (SY) IC1300 6-718-913-01 IC OZ5329IGN-A1-0-TR < JACK > J1 J401 J801 1-815-185-13 1-822-713-11 1-566-822-81 JACK (ANT) (ANTENNA) JACK, PIN 2P (AUDIO OUT, REAR/SUB) JACK (REMOTE IN) < COIL > L1 L301 L1300 L1301 1-400-073-21 1-460-443-11 1-216-296-11 1-481-904-11 INDUCTOR CHOKE COIL SHORT CHIP CHOKE COIL 4.7uH 140uH 0 47uH < TRANSISTOR > Q301 Q401 Q402 Q403 Q404 8-729-620-13 6-552-937-01 6-552-937-01 6-552-937-01 6-552-937-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC4154TP-1EF LTC014TUBFS8TL LTC014TUBFS8TL LTC014TUBFS8TL LTC014TUBFS8TL R421 R422 R423 R424 R429 1-218-953-11 1-216-833-11 1-218-953-11 1-216-833-11 1-216-801-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 1K 10K 22 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/10W 1/10W Q405 Q406 Q407 Q409 Q710 6-552-937-01 6-552-937-01 6-552-410-01 6-552-430-01 8-729-024-43 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR LTC014TUBFS8TL LTC014TUBFS8TL DRA5114E0L DRC5114E0L 2SA1365-T112-1EF R430 R431 R432 R433 R434 1-216-864-11 1-216-864-11 1-216-833-11 1-216-296-11 1-216-296-11 SHORT CHIP SHORT CHIP METAL CHIP SHORT CHIP SHORT CHIP 0 0 10K 0 0 5% 1/10W Note 1: When IC501 is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5. 50 Note 2: IC501 has been changed in the midway of production. When IC501 is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE MAIN Ref. No. Part No. Description Part No. Description R501 R502 R510 R511 R513 1-218-977-11 1-216-845-11 1-218-941-81 1-218-941-81 1-218-977-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100 100 100K 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/16W 1/16W Remark Ref. No. R586 R600 R601 R602 R603 1-216-845-11 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W Remark R514 R515 R516 R517 R518 1-208-911-11 1-208-911-11 1-208-911-11 1-218-953-11 1-218-953-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 1K 1K 0.5% 0.5% 0.5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R604 R605 R606 R607 R613 1-216-809-11 1-218-977-11 1-218-977-11 1-218-977-11 1-218-973-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100K 100K 100K 47K 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W R521 R522 R523 R524 R525 1-218-971-11 1-218-971-11 1-218-941-81 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 33K 33K 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R614 R615 R616 R617 R618 1-218-965-11 1-218-953-11 1-218-953-11 1-218-953-11 1-218-953-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R527 R529 R531 R533 R534 1-218-977-11 1-218-949-11 1-218-977-11 1-218-953-11 1-218-953-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 470 100K 1K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R619 R620 R621 R622 R623 1-218-953-11 1-218-953-11 1-218-941-81 1-216-833-11 1-218-990-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 1K 1K 100 10K 0 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W R535 R536 R538 R539 R540 1-218-949-11 1-218-977-11 1-218-965-11 1-218-990-81 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 470 100K 10K 0 100K 5% 5% 5% 1/16W 1/16W 1/16W 5% 1/10W R625 R629 R636 R637 R638 1-216-845-11 1-218-941-81 1-218-961-11 1-218-971-11 1-218-971-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100 4.7K 33K 33K 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W R541 R542 R543 R544 R545 1-245-604-11 1-218-981-91 1-218-990-81 1-216-857-11 1-216-845-11 METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP 10M 220K 0 1M 100K 5% 5% 1/16W 1/16W 5% 5% 1/10W 1/10W R639 R642 R643 R644 R645 1-218-965-11 1-218-965-11 1-216-845-11 1-218-941-81 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 100K 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/16W 1/16W R546 R547 R548 R549 R552 1-218-977-11 1-218-941-81 1-218-990-81 1-218-990-81 1-218-977-11 METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP 100K 100 0 0 100K 5% 5% 1/16W 1/16W 5% 1/16W R646 R647 R648 R649 R652 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-218-977-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R553 R555 R556 R557 R560 1-218-949-11 1-218-990-81 1-218-957-11 1-218-957-11 1-218-977-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 470 0 2.2K 2.2K 100K 5% 1/16W 5% 5% 5% 1/16W 1/16W 1/16W R653 R654 R655 R656 R661 1-218-977-11 1-218-977-11 1-216-097-11 1-218-977-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 100K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/16W 1/16W R561 R562 R563 R564 R565 1-218-990-81 1-218-990-81 1-218-941-81 1-216-809-11 1-218-977-11 SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 0 0 100 100 100K METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP 10K 1M 0 4.7 4.7 1/16W 1/16W 1/16W 1/10W 1/16W 1-218-965-11 1-218-989-11 1-218-990-81 1-216-793-11 1-216-793-11 5% 5% 5% 5% 5% R667 R668 R669 R671 R672 5% 5% 1/10W 1/10W R566 R567 R568 R569 R570 1-218-977-11 1-218-977-11 1-216-845-11 1-218-977-11 1-218-941-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 100K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/16W 1/16W R673 R674 R675 R676 R685 1-216-835-11 1-216-835-11 1-218-977-11 1-218-977-11 1-218-990-81 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 15K 15K 100K 100K 0 5% 5% 5% 5% 1/10W 1/10W 1/16W 1/16W R571 R572 R573 R574 R575 1-218-941-81 1-218-941-81 1-218-941-81 1-218-941-81 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/10W R688 R689 R690 R691 R692 1-216-864-11 1-216-864-11 1-220-200-81 1-218-971-11 1-218-990-81 SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP 0 0 30K 33K 0 5% 5% 1/16W 1/16W R576 R577 R578 R579 R584 1-218-977-11 1-218-977-11 1-216-833-11 1-216-833-11 1-218-977-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 10K 10K 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/10W 1/10W 1/16W R693 R695 R697 R699 R710 1-218-990-81 1-216-864-11 1-218-990-81 1-216-864-11 1-218-953-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP 0 0 0 0 1K 5% 1/16W 51 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 MAIN SENSOR Ref. No. SERVO Part No. Description R711 R712 R714 R715 R716 1-218-929-11 1-220-802-11 1-218-990-81 1-218-990-81 1-218-990-81 METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP SHORT CHIP 10 3.3 0 0 0 5% 5% Remark R717 R718 R719 R720 R721 1-218-947-11 1-218-947-11 1-218-947-11 1-218-947-11 1-218-947-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 330 330 330 330 330 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R722 R723 R724 R725 R726 1-218-989-11 1-218-955-11 1-218-958-11 1-218-958-11 1-218-965-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1M 1.5K 2.7K 2.7K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R727 R728 R729 R730 R731 1-218-965-11 1-218-977-11 1-218-977-11 1-218-977-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/10W R732 R733 R736 R737 R738 1-218-990-81 1-218-990-81 1-218-977-11 1-218-953-11 1-218-953-11 SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 0 0 100K 1K 1K 5% 5% 5% 1/16W 1/16W 1/16W R739 R740 R741 R742 R743 1-218-953-11 1-218-953-11 1-218-941-81 1-216-841-11 1-218-967-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 100 47K 15K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/16W R744 R745 R746 R747 R748 1-218-983-11 1-218-941-81 1-218-990-81 1-218-990-81 1-218-990-81 METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP SHORT CHIP 330K 100 0 0 0 5% 5% 1/16W 1/16W R749 R750 R751 R761 R763 1-218-990-81 1-218-969-11 1-218-969-11 1-216-864-11 1-216-864-11 SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP 0 22K 22K 0 0 R764 R765 R766 R814 R818 1-216-864-11 1-216-864-11 1-216-864-11 1-218-981-91 1-218-981-91 SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP 0 0 0 220K 220K R819 R820 R833 R864 R865 1-218-953-11 1-218-953-11 1-218-977-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP 1K 1K 100K 0 0 R899 R1300 R1301 R1302 R1305 1-216-296-11 1-216-817-11 1-216-809-11 1-218-977-11 1-208-905-11 SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 470 100 100K 5.6K 5% 5% 5% 0.5% 1/10W 1/10W 1/16W 1/16W R1307 R1308 R1310 R1311 R1312 1-208-933-11 1-208-933-11 1-218-953-11 1-218-885-11 1-218-871-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 82K 82K 1K 39K 10K 0.5% 0.5% 5% 0.5% 0.5% 1/16W 1/16W 1/16W 1/10W 1/10W 1/16W 1/16W Ref. No. R1313 R1315 Description 1-216-849-11 1-218-953-11 METAL CHIP METAL CHIP Remark 220K 1K 5% 5% 1/10W 1/16W < TUNER UNIT > TU901 A-1878-198-A 5% 5% 1/16W 1/16W TUX-DSP02 (TUNER UNIT) < VIBRATOR > X501 1-814-544-21 VIBRATOR, CERAMIC (7.92 MHz) (EXCEPT EA) X501 1-814-548-11 VIBRATOR, CERAMIC (7.92 MHz) (EA) X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768 kHz) X601 1-814-304-11 VIBRATOR, CRYSTAL (12 MHz) X701 1-795-561-21 VIBRATOR, CERAMIC (16.934 MHz) ************************************************************* SENSOR BOARD ************* When the SENSOR board is defective, exchange the MECHANICAL BLOCK (Z) ASSY 08 (Former type) or MECHANICAL BLOCK (11CA) ASSY (New type). ************************************************************* A-1823-723-A A-1866-089-A SERVO BOARD, COMPLETE (Former type) SERVO BOARD, COMPLETE (New type) ********************** When the SERVO board is defective, exchange the complete mounted board. ************************************************************* MISCELLANEOUS ************** 6 1-839-372-11 6 1-839-387-11 61 66 1-780-968-11 A-1831-758-A 66 A-1831-758-B 66 A-1831-765-A 66 A-1831-765-B 66 A-1831-774-A 66 A-1831-774-B 5% 5% 1/16W 1/16W 66 A-1831-783-A 5% 5% 5% 1/16W 1/16W 1/16W 66 A-1831-783-B 66 A-1831-789-A 66 A-1831-789-B 66 A-1831-795-A 66 A-1831-795-B 66 A-1831-800-A 66 A-1831-800-B Note 1: In this unit, the complete SERVO board has been changed in the midway of production. When replacing the complete SERVO board, refer to “ABOUT THE MG-101CA-188 OF FORMER AND NEW” on page 6. 52 Part No. CONNECTION CORD FOR AUTOMOBILE (POWER) (US, CND, E, EA, MX, KR, IND) CONNECTION CORD (ISO) (POWER) (AEP, RU, UK, AR) CONDUCTIVE BOARD, CONNECTION PANEL OVERALL ASSY, FRONT (GT40U: US, CND) (Former type) PANEL OVERALL ASSY, FRONT (GT40U: US, CND) (New type) PANEL OVERALL ASSY, FRONT (GT40UW) (Former type) PANEL OVERALL ASSY, FRONT (GT40UW) (New type) PANEL OVERALL ASSY, FRONT (GT40U: RU) (Former type) PANEL OVERALL ASSY, FRONT (GT40U: RU) (New type) PANEL OVERALL ASSY, FRONT (GT45U: E, EA, AR) (Former type) PANEL OVERALL ASSY, FRONT (GT45U: E, EA, AR) (New type) PANEL OVERALL ASSY, FRONT (GT44U: IND) (Former type) PANEL OVERALL ASSY, FRONT (GT44U: IND) (New type) PANEL OVERALL ASSY, FRONT (GT44U: AEP, UK) (Former type) PANEL OVERALL ASSY, FRONT (GT44U: AEP, UK) (New type) PANEL OVERALL ASSY, FRONT (GT47UE) (Former type) PANEL OVERALL ASSY, FRONT (GT47UE) (New type) Note 2: FRONT PANEL OVERALL ASSY (Ref. No. 66) has been changed in the midway of production. When FRONT PANEL OVERALL ASSY (Ref. No. 66) is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 Ref. No. Part No. Description 66 A-1835-141-A 66 A-1835-141-B 66 A-1837-401-A PANEL OVERALL ASSY, FRONT (GT40U: AEP, UK) (Former type) PANEL OVERALL ASSY, FRONT (GT40U: AEP, UK) (New type) PANEL OVERALL ASSY, FRONT (GT42UE) (Former type) 66 A-1837-401-B 66 A-1847-849-A 66 A-1847-849-B 66 A-1850-669-A 66 A-1850-669-B 101 101 0 102 0 103 CN902 A-1313-179-A A-1866-801-A A-1284-705-A X-2149-672-1 1-822-798-11 Remark PANEL OVERALL ASSY, FRONT (GT42UE) (New type) PANEL OVERALL ASSY, FRONT (GT45U: MX) (Former type) PANEL OVERALL ASSY, FRONT (GT45U: MX) (New type) PANEL OVERALL ASSY, FRONT (GT45U: KR) (Former type) PANEL OVERALL ASSY, FRONT (GT45U: KR) (New type) MECHANICAL BLOCK (Z) ASSY 08 (Former type) MECHANICAL BLOCK (11CA) ASSY (New type) DAXEV08//Q SERVICE ASSY, OP (DAX-25A) USB CONNECTOR (USB) FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10 A/32 V) IC902 6-600-806-01 IC PNJ4813M01S0 J901 1-822-148-11 SMALL TYPE JACK (VERTICAL) (AUX) LCD901 1-811-224-11 DISPLAY PANEL, LIQUID CRYSTAL RE901 1-487-023-22 ROTARY ENCODER (PUSH SELECT (VOLUME)) ************************************************************* Ref. No. Part No. Description 4-410-179-21 MANUAL, INSTRUCTION INSTALL (ENGLISH, KOREAN) (KR) MANUAL, INSTRUCTION (ENGLISH, ARABIC, PERSIAN) (EA) 4-410-607-11 Remark 4-410-607-22 MANUAL, INSTRUCTION (ENGLISH, KOREAN) (KR) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS ************************************** 151 152 153 X-2548-178-1 1-465-459-51 1-839-387-11 154 1-839-372-11 155 4-276-003-01 156 156 157 4-183-280-02 4-278-065-01 X-3381-154-1 158 159 160 X-3382-926-1 3-349-410-11 3-934-325-01 FRAME ASSY, FITTING ADAPTOR, ANTENNA (AEP, RU, UK, AR) CONNECTION CORD (ISO) (POWER) (AEP, RU, UK, AR) CONNECTION CORD FOR AUTOMOBILE (POWER) (US, CND, E, EA, MX, KR, IND) KEY (FRAME) (1 piece) COLLAR (EXCEPT AEP, UK, MX, AR) COLLAR (AEP, UK, MX, AR) SCREW ASSY (BS4), FITTING (GT44U: IND/GT45U) SCREW ASSY (BS), FITTING (AEP, RU, UK) BUSHING (EXCEPT US, CND) SCREW, +K (5X8) TAPPING (1 piece) (EXCEPT AEP, RU, UK) 151 152 153 154 155 156 ACCESSORIES ************ 1-489-810-21 4-284-500-11 4-284-500-21 4-284-500-31 4-284-500-42 4-284-500-51 4-284-501-12 4-284-501-22 4-284-501-31 4-284-501-41 4-284-501-51 4-284-501-61 4-410-179-11 REMOTE COMMANDER (RM-X211) (EXCEPT AEP, RU, UK) MANUAL, INSTRUCTION (ENGLISH, FRENCH) (GT40U: US, CND) MANUAL, INSTRUCTION (ENGLISH, SPANISH) (GT40UW) MANUAL, INSTRUCTION (ENGLISH, FRENCH, GERMAN, ITALIAN, DUTCH) (AEP, UK) MANUAL, INSTRUCTION (RUSSIAN, UKRAINIAN) (RU) MANUAL, INSTRUCTION (ENGLISH, SPANISH) (E, MX, AR, IND) MANUAL, INSTRUCTION INSTALL (ENGLISH, FRENCH) (GT40U: US, CND) MANUAL, INSTRUCTION INSTALL (ENGLISH, SPANISH) (GT40UW) MANUAL, INSTRUCTION INSTALL (ENGLISH, FRENCH, GERMAN, ITALIAN, DUTCH) (AEP, UK) MANUAL, INSTRUCTION INSTALL (RUSSIAN, UKRAINIAN) (RU) u2 157 158 159 160 u4 MANUAL, INSTRUCTION INSTALL (ENGLISH, SPANISH) (E, MX, IND) MANUAL, INSTRUCTION INSTALL (ENGLISH, SPANISH) (AR) MANUAL, INSTRUCTION INSTALL (ENGLISH, ARABIC, PERSIAN) (EA) Note 1: FRONT PANEL OVERALL ASSY (Ref. No. 66) has been changed in the midway of production. When FRONT PANEL OVERALL ASSY (Ref. No. 66) is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7. Note 2: MECHANICAL BLOCK ASSY (Ref. No. 101) has been changed in the midway of production. When MECHANICAL BLOCK ASSY (Ref. No. 101) is replaced, be sure to refer to “ABOUT THE MG-101CA-188 OF FORMER AND NEW” on page 6. Note 3: Refer to the servicing notes “NOTE FOR REPLACEMENT OF THE USB CONNECTOR (CN902) AND THE AUX JACK (J901)” on page 4, if replacing CN902 and J901. 53 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE MEMO 54 CDX-GT40U/GT40UW/GT42UE/ GT44U/GT45U/GT47UE US Model CDX-GT40U/GT40UW SERVICE MANUAL Canadian Model CDX-GT40U AEP Model UK Model Ver. 1.2 2011.11 CDX-GT40U/GT44U E Model CDX-GT45U SUPPLEMENT-1 File this supplement with the service manual. Indian Model CDX-GT44U Russian Model CDX-GT40U/GT42UE/GT47UE Subject: PRINTED WIRING BOARD – MAIN board for Saudi Arabia model – In this unit, MAIN board is different only Saudi Arabia model. Printed wiring board of Saudi Arabia model is described in this supplement-1. Refer to original service manual and supplement-2 for other information 9-893-214-81 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 1. DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. Note: • X : Parts extracted from the component side. • Y : Parts extracted from the conductor side. • a : Through hole. • : Pattern from the side which enables seeing. (The other layers’ patterns are not indicated.) Caution: Pattern face side: (SIDE B) Parts face side: (SIDE A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. • Indication of transistor. C Q These are omitted. B E Note: When COMPLETE MAIN BOARD is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5 on original service manual. 2 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.4 1-1. 14 PRINTED WIRING BOARD – MAIN Section (1/2) – • 13 12 11 : Uses unleaded solder. 10 9 8 7 6 5 4 3 2 1 A MAIN BOARD (SIDE A) C426 R403 R411 R402 R432 C414 FB750 FB751 C748 R727 C747 R726 R10 R697 FB720 C729 C727 C728 C732 R405 R424 R409 R421 C323 R400 FB694 C759 R764 R723 C735 C734 E C11 R102 C751 FB717 1 40 C750 C203 F C416 R524 C513 C522 R518 C523 R517 R522 CL004 81 CL003 80 Q409 R576 R541 C508 R430 R525 R521 R529 R523 C504 C510 50 51 R560 R510 R511 R577 R574 R573 R572 R571 R569 R570 IFM501 S8 Barcode R122 C1311 R1310 R1315 C100 1-885-266- Note 1: When IC501 is replaced, the destination setting is necessary. Refer to “NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC501) REPLACING” on page 5 on original service manual. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 3 H R121 R864 R501 R565 R566 R567 R584 R563 C521 R561 30 31 R562 R552 R555 R557 G R116 R544 IC501 R1311 R1312 R1307 C1306 20 21 C1312 C1310 R1308 9 R1313 C756 C689 C744 D530 C401 C520 R556 C1305 16 8 R1300 R546 FB501 C610 C1304 2 C514 C502 R547 C518 R548 R549 IC1300 1 D IC401 R543 3 C1308 R1302 C1317 C1316 C1309 C1315 C507 R601 R603 R673 R674 R675 FB610 R668 R695 R669 C616 FB612 L1301 R724 R553 D731 20 C313 Q407 100 1 IFM601 R685 C609 D1300 1 TP682 16 C410 C419 R433 R725 C752 FB718 R717 C726 R516 C685 L1300 R865 R531 R535 R401 C753 FB719 R718 C512 R514 R527 R538 IC403 4 IFM680 C420 C D403 R515 R533 R534 X501 X601 R661 R688 C422 R410 TP333 C737 R429 C615 C614 C1307 R656 TP334 R667 R655 C1301 R653 R654 TP635 R644 R646 R648 R652 CN501 TP634 R645 R690 76 75 50 51 R642 R672 R671 C612 R637 R636 TP633 1 IC601 R647 R649 R513 8 R629 R639 C613 FB611 R638 R600 C683 C601 1 100 C617 R676 C608 25 26 1 R602 C605 R615 R605 R689 C606 C425 D401 TP721 R613 R606 C725 R539 R614 R607 R720 IFM50 TP724 TP723 FB721 R719 R542 R623 TP720 C688 FB696 R693 C754 C730 R721 R716 C792 TP722 IC682 FB724 C722 C721 TP719 IC681 3 C738 IFM701 Q406 C415 5 4 C764 FB398 C308 R712 R711 C724 R714 R617 X701 Q404 R406 R404 C424 FB698 C687 1 C746 51 50 25 3 1 4 5 FB762 C733 Q710 R710 TP718 26 B E C718 C717 C719 C711 C607 FB695 C690 R692 FB722 C787 C786 C686 C761 76 75 IC701 C712 R616 R736 C741 R729 R728 C745 C742 R722 C739 C743 C766 C777 C789 C782 C403 TP732 TP736 100 1 C783 C784 C788 C715 C714 C713 C776 R745 C778 C771 R749 IFM70 R750 C779 R751 FB782 R715 R744 R742 Q405 R423 C411 R761 R536 R747 R748 C768 R309 TP741 TP742 TP743 C772 R743 R746 TP735 TP733 C767 TP739 R740 R739 TP740 R741 R738 IFM60 R305 C312 R763 R733 R732 R730 R731 TP738 R1305 TP737 C720 R737 5 C315 Q403 C413 C309 TP734 R814 R306 Q402 R422 C457 B C15 R301 Q801 Q802 R818 CN601 R304 C409 C398 R311 D321 R378 R300 C330 D323 R621 R618 R619 R620 C317 C321 Q401 R302 C331 Q301 C303 R303 R340 R312 D806 R314 D805 R819 R820 Q803 R313 R833 R307 C326 C319 R407 C314 R308 Note 2: IC501 has been changed in the midway of production. When IC501 is replaced, be sure to refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7 on original service manual. 3 11 Note 3: C741, C743, C745, CN501 and CN601 have been deleted in the midway of production. I J CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Ver. 1.3 1-2. PRINTED WIRING BOARD – MAIN Section (2/2) – • 2 1 3 : Uses unleaded solder. 4 5 6 7 8 9 10 11 12 13 14 J401 AUDIO OUT REAR/SUB J1 (ANTENNA) A -1 L J801 (REMOTE IN) MAIN BOARD (SIDE B) -2 R CN301 FB803 W002 C306 16 1 8 D320 C301 FB802 9 F4 JL011 19 C334 JL012 R396 A001 JL013 D318 R395 C J801 FB801 1 37 R19 18 C305 C399 J1 FU601 17 2 C327 C335 C302 B IC301 C311 36 C332 J401 JL009 D324 AB1 4 L1300 IC402 C760 JL725 TU901 TUNER UNIT (TUX-DSP02) R13 R12 TP761 R11 E C780 JL730 JL710 JL712 JL711 JL722 JL709 JL721 JL728 JL708 JL707 JL706 TP785 C10 11 JL720 JL729 JL717 JL727 JL719 JL705 JL704 JL716 JL715 R766 JL726 JL703 JL714 C716 JL702 JL713 JL718 1 2 R199 F 27 JL723 TP781 C781 L1 9 12 CN700 28 JL724 CN01 C437 TP696 JL701 JL700 R625 C438 C436 R899 R434 TP695 FB760 C701 C402 R765 FB19 1 3 W001 R699 D C407 5 FB890 FB891 R431 13 10 1 JL010 R622 JL008 TO SERVO BOARD R419 TP642 R604 TP632 R578 R579 IFM502 TP640 R575 R417 C440 C442 R545 JL002 D103 CL061 R502 D101 R568 JL005 CL077 CL079 CL075 CL071 CL073 CL066 CL069 JL003 JL001 R1301 CL082 C103 2 CL074 CL076 CL072 CL070 CL063 CL068 CL064 CL065 C101 JL004 JL006 CL081 JL731 JL007 D102 CL067 I JL732 TP643 R420 C439 R415 R416 JL733 R643 TP641 R586 D119 R418 H TP342 R564 R540 G (Refer to page 25 on original service manual) TP644 X502 IFM500 D110 CL078 1-885-266- 19 21 1 11 20 22 CN102 Note: Refer to “ABOUT CHANGE OF THE LCD DRIVER IC (IC901) ON THE KEY BOARD” on page 7 on original service manual for how to distinguish New/Former types. (Refer to page 31 on original A CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE KEY BOARD service manual (Former type) or page 3 on supplement-2 (New type)) CN901 4 4 CDX-GT40U/GT40UW/GT42UE/ GT44U/GT45U/GT47UE US Model CDX-GT40U/GT40UW SERVICE MANUAL Canadian Model CDX-GT40U AEP Model UK Model Ver. 1.3 2012.06 CDX-GT40U/GT44U E Model CDX-GT45U SUPPLEMENT-2 Russian Model CDX-GT40U/GT42UE/GT47UE File this supplement with the service manual. Subject: Change of KEY board (Suffix-21/-22) In this set, the LCD driver IC (IC901) on the KEY board has been changed in the midway of production. The following changes are performed by this change. • Change of the KEY board (suffix-21/-22) (Refer to this supplement-2) • Change of part No. of the FRONT PANEL OVERALL ASSY (Refer to page 44, 52 and 53 on original service manual) • Change of part No. of the complete MAIN board (Refer to page 43 and 48 on original service manual) • Change of part for Ref No. IC501 on the MAIN board (Refer to page 50 on original service manual) In this unit, KEY board has been changed in the midway of production. Discrimination, printed wiring board, schematic diagram and electrical parts list of changed KEY board are described in this supplement-2. Refer to original service manual and supplement-1 for other information. Note: When the parts of new front panel and the parts of old main unit are combined, this unit does not operate normally. 9-893-214-82 Indian Model CDX-GT44U CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 1. NEW/FORMER DISCRIMINATION Three kinds of following distinguish methods exist. • Distinguish method by serial number printed on the model number label (Refer to right side for the serial number). Serial number Model Destination Former type New type US and Canadian models* 1864691 or smaller 1864692 or lager Canadian model (for CXS-GT4016F) 1554521 or smaller 1554522 or lager AEP and UK models 1885791 or smaller 1885792 or lager Russian model 1822499 or smaller 1822500 or lager CDXGT40UW US model 1864116 or smaller 1864117 or lager CDXGT42UE Russian model 1850792 or smaller 1850793 or lager AEP and UK models 1939738 or smaller 1939739 or lager Indian model 1865831 or smaller 1865832 or lager E model 1811434 or smaller 1811435 or lager Saudi Arabia model 1878981 or smaller 1878982 or lager Mexican model 1838226 or smaller 1838227 or lager Argentina model 1798061 or smaller 1798062 or lager Korean model 1826514 or smaller 1826515 or lager Russian model 1858886 or smaller 1858887 or lager – Main unit (Bottom side) – Model number label Displayed characters/values are example. • Distinguish method by part No. printed on the KEY board – KEY Board (Side A) – CDXGT40U CDXGT44U Former type : 1-884-821-11 New type : 1-884-821-21 or 1-884-821-22 • Distinguish method by LCD driver IC (IC901) on the KEY board – KEY Board (Side B) – CDXGT45U IC901 CDXGT47UE *CXS-GT4016F (US model) is Former type only. Former type : LC75839 New type : PT6587-LQ 2. DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. Note: • X : Parts extracted from the component side. • Y : Parts extracted from the conductor side. • : Pattern from the side which enables seeing. (The other layers’ patterns are not indicated.) Note: • All capacitors are in μF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • C : Panel designation. Caution: Pattern face side: (SIDE B) Parts face side: (SIDE A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. • Indication of transistor. C Q These are omitted. B E • Abbreviation RU : Russian model 2 • A : B+ Line. • Voltages are dc with respect to ground under no-signal (detuned) conditions. no mark : FM • Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. • Signal path. L : AUX c : USB • Abbreviation RU : Russian model CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE PRINTED WIRING BOARD – KEY Board – • 3 A LED933,934,S905 m . SEEK - R920 R921 11 12 13 14 LED946,S901 Z S901 R954 52 1 R903 S906 R970 LED901 LED932 S905 LCD901 LIQUID CRYSTAL DISPLAY PANEL LED944 LED952 R952 LED942 LED934 C 10 LED901 (LCD BACK LIGHT) LED954 LED954,S906 9 LED938 LED932,S904 S904 8 KEY BOARD (SIDE A) LED950 LED940 7 S907 R990 LSW911 LSW912 LSW909 R984 LSW910 LSW907 LSW908 LSW906 LSW905 R980 B 6 S902 R946 S903 5 LED950,S902 SOURCE / OFF LED936 LED936,S903 SEEK + > M 4 LED946 2 1 : Uses unleaded solder. R982 2-1. 21, 22 1-884-821- D LED952,S907 MODE LSW912 LED938,940,942 (ILLUMINATION) AF/TA/ PTY (AEP, RU, UK) LSW911 LSW910 LSW909 LSW908 LSW907 LSW906 1 /ALBUM V 2 /ALBUM v 3 /REP 4 /SHUF 5 /ZAP 6 /PAUSE (21, 22) LSW905 / DSPL SCRL PTY (EXCEPT AEP, RU, UK) E (Refer to page 25 on original service manual (except Saudi Arabia model) or page 4 on supplement-1 (Saudi Arabia model)) MAIN BOARD CN102 J901 A KEY BOARD (SIDE B) R927 49 48 2 20 R901 D902 J901 IFM4 R902 R907 R998 IC901 1 C916 C909 C911 R916 IFM2 R918 R922 64 16 17 R909 R961 R958 R972 1 CN901 19 CN902 R906 CN902 33 32 C912 R991 Q901 C901 C903 C902 C904 IFM1 R976 IFM6 Q905 R992 D912 R940 RE901 R910 R908 R993 D916 R956 R974 Q903 D901 R917 Barcode R999 R925 R942 R944 R915 R904 R926 R924 G R923 R986 IFM3 R994 R995 C915 R996 D911 R997 R988 R950 R966 C906 IC902 R968 IC902 C910 F H AUX (USB) R919 FB901 I RE901 FB902 PUSH ENTER/SELECT FB903 R905 R948 21, 22 1-884-821- (21, 22) Note: Refer to the servicing notes “NOTE FOR REPLACEMENT OF THE USB CONNECTOR (CN902) AND THE AUX JACK (J901)” on page 4 on original service manual, if replacing CN902 and J901. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE 3 3 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE SCHEMATIC DIAGRAM – KEY Board – 12 S[9] S[11] S[12] S[13] S[14] S[15] S[16] S[17] S[18] S[19] S[20] 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 KEY BOARD A R956 *3 5 3 1 6 4 2 LSW909 3/REP R948 *4 C915 1000p R952 *4 R958 *5 R995 1.5k R984 *7 *4 R940,944 220 (AEP,RU,UK) 820 (EXCEPT AEP,RU,UK) R946,950,954,956,970,972 270 (AEP,RU,UK) 1k (EXCEPT AEP,RU,UK) R948,952,968 330 (AEP,RU,UK) 1.2k (EXCEPT AEP,RU,UK) 4 3 R926 2.2k S907 MODE LED938,940,942,944 (ILLUMINATION) *3 5 LED950 *1 SOURCE / OFF F R970 *3 R968 *4 LED952 *1 MODE G *1 H R958,974 270 (AEP,RU,UK) 1.2k (EXCEPT AEP,RU,UK) *6 R966 330 (AEP,RU,UK) 1k (EXCEPT AEP,RU,UK) 2 R996 1.8k R986 *7 *7 *8 R972 *3 R927 0 R974 *5 LED932,934,936,938,940,942,944,946,950,952,954 SML-D12P8WT86TK (AEP,RU,UK) SML-D12V8WT86TN (EXCEPT AEP,RU,UK) 5 3 1 6 4 2 R997 2.2k R988 *8 LSW912 AF/TA/ PTY (AEP,RU,UK) PTY R918 0 *9 LSW911 1/ALBUM RE901 PUSH ENTER/ SELECT R919 0 5 3 1 6 4 2 (EXCEPT AEP,RU,UK) R990 *9 R999 0 R980,982,984,986 100 (AEP,RU,UK) 150 (EXCEPT AEP,RU,UK) R988 150 (AEP,RU,UK) 220 (EXCEPT AEP,RU,UK) R990 180 (AEP,RU,UK) 220 (EXCEPT AEP,RU,UK) SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG12 SEG13 SEG11 SEG10 SEG9 SEG7 SEG8 SEG6 SEG5 SEG35 18 SEG36 17 8 9 10 11 12 13 14 15 16 S[28] 2.6 S[29] 2.6 S[30] 2.6 S[31] 2.6 S[32] 2.6 S[33] 2.6 S[34] 2.6 S[35] 2.6 S[36] 2.6 2.6 2.6 2.6 2.6 2.6 2.6 S[43] S[42] S[41] S[40] S[39] S[38] S[37] SEG37 7 SEG38 6 SEG39 5 SEG40 4 SEG41 3 SEG42 2 SEG43 SEG44 1 2.6 DIMMER S[44] R917 470 SEG45 0.2 SEG46 470 3.3 2.6 0.1 2.6 R916 S[45] CLK 470 SEG47 OUT VCC GND 63 LCD_CLK 64 LCD_DATA R915 S[27] 2.6 LCD901 LIQUID CRYSTAL DISPLAY PANEL COM[1] COM[2] COM[3] COM[4] S[48] S[47] S[46] S[45] S[44] S[43] S[42] S[41] S[40] S[39] S[38] S[37] S[36] S[35] S[34] S[33] S[32] S[31] S[30] S[29] S[28] S[27] S[26] S[25] S[24] S[23] S[22] S[21] S[20] S[19] S[18] S[17] S[16] S[15] S[14] S[13] S[12] S[11] S[10] S[9] S[8] S[7] S[6] S[5] S[4] S[3] S[2] S[1] 1 I *5 1 4 LED954 *1 6 R966 *6 3 LSW910 2/ALBUM 5.1 5.2 Q903 RT6N140C-TP-1 LED DRIVE 5.1 *2 SEG33 20 SEG34 19 4.8 CE 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 R925 1.8k 61 INH 62 LCD_CE S[1] S[26] 2.6 8 2 SEG31 22 SEG32 21 S[25] 2.6 7 4 2.6 59 VSS 60 SEG52 S[24] 2.6 6 6 R994 1.2k 1.7 S[23] 2.6 5 4/SHUF SEEK- 0.1 LSW908 0.1 SEG29 24 SEG30 23 S[22] 2.6 4 1 C901 57 VDD1 58 VDD2 S[21] 2.6 3 C916 1000p LED944 *1 R946 *3 2 1 3 3.4 2.6 2 LED942 *1 LED940 *1 27 27 E (USB) 5 R907 R906 R954 *3 R924 1.5k 5.1 IC901 PT6587-LQ LCD CONTROL 0.1 R904 1M C904 0.47 SEG27 26 SEG28 25 C902 DATA Q901 RT1N140C-TP-1 LCD BACK LIGHT DRIVE R993 1k LED946 *1 LED938 *1 R950 *3 5.2 IC901 55 SEG2 56 VDD S[46] R923 1.2k 2.6 2.6 S904 S906 GND-USB 0.1 2 0.1 S905 D+ 4 S[2] S[47] 6 D D- 1 5/ZAP GND 20 VBUS-USB 3 LSW907 CE ILL(FP+B) 18 PANEL_SW 19 CN902 4P 5 2.6 SEG25 28 SEG26 27 SEG48 R922 1k COM[1] 53 COM2 54 COM1 2.6 S903 SEEK+ Q905 RT1N140C-TP-1 DIMMER 0.1 SWITCH 5.1 2.6 SEG23 30 SEG24 29 S[48] R961 1.5k COM[2] 51 COM4 52 COM3 COLOR2 CLK R910 120 R992 1k 2.6 SEG21 32 SEG22 31 COLOR1 LCD_CE 16 LCD_CLK 17 2 2.6 COM[3] 49 SEG4 50 SEG3 BACK-LIGHT DATA 4 C903 0.1 2.6 COM[4] 5.1 SIRCS 14 LCD_DATA 15 R909 120 6/PAUSE 6 LED936 *1 SEEK+ KEY_1 12 KEY_0 13 1 2.6 S[3] 5.1 9 3 LSW906 R940 *2 RE_0 10 RE_1 11 A C R944 *2 R921 1k 5 R976 0 REMOTE CONTROL SIGNAL RECEIVER S[4] 5.1 AUX_GND S902 SOURCE / OFF R908 120 18p 8 R982 *7 IC902 18p AUX_R R991 820 C906 0.1 18p 7 R980 *7 C909 AUX_L 2 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 R903 100 C910 6 4 IC902 PNJ4813M01S0 C911 KEY_GND 6 R902 150 D901 DA2J10100L 5 1 D902 RKZ5.1B2KGP1 GND 3 LED901 NESW505DT-A0-UV (LCD BACK LIGHT) 4 R920 820 LED932 *1 D+ RKZ6.8B2KGP1 3 RKZ6.8B2KGP1 D- D911 2 0.1 USB_VBUS S901 LSW905 DSPL / SCRL 5 R942 0 D912 MAIN BOARD (3/5) CN102 (Refer to page 28 on original service manual) 1 FB903 C912 B USB_GND R905 0 SEEK- CN901 20P LED934 *1 J901 AUX D916 RKZ6.8B2KGP1 FB901 R901 150 R998 1k FB902 13 S[10] 11 2.6 10 S[8] 9 2.6 8 S[7] 7 2.6 6 S[6] 5 S[5] 4 2.6 3 2 2.6 1 2.6 2-2. CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE Note: Refer to the servicing notes “NOTE FOR REPLACEMENT OF THE USB CONNECTOR (CN902) AND THE AUX JACK (J901)” on page 4 on original service manual, if replacing CN902 and J901. 4 4 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE KEY 3. ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Ref. No. Part No. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • CAPACITORS uF: μF • COILS uH: μH Description Remark KEY BOARD ********** Ref. No. Description LED938 6-502-325-11 LED940 6-502-193-11 LED SML-D12P8WT86TK (ILLUMINATION) (AEP, RU, UK) LED SML-D12V8WT86TN (ILLUMINATION) (EXCEPT AEP, RU, UK) C901 C902 C903 C904 C906 1-100-597-91 1-100-597-91 1-100-597-91 1-125-891-11 1-100-597-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.47uF 0.1uF 10% 10% 10% 10% 10% 25V 25V 25V 10V 25V LED940 6-502-325-11 LED942 6-502-193-11 LED942 6-502-325-11 C909 C910 C911 C912 C915 1-162-918-11 1-162-918-11 1-162-918-11 1-100-597-91 1-162-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 18PF 18PF 18PF 0.1uF 0.001uF 5% 5% 5% 10% 10% 50V 50V 50V 25V 50V LED944 6-502-193-11 LED944 6-502-325-11 LED946 6-502-193-11 C916 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CONNECTOR > LED946 LED950 6-502-325-11 6-502-193-11 PLUG, CONNECTOR 20P LED950 6-502-325-11 < DIODE > LED952 6-502-193-11 LED952 LED954 6-502-325-11 6-502-193-11 LED954 6-502-325-11 D901 D902 D911 D912 D916 1-842-265-22 6-502-961-01 6-503-202-01 6-503-205-01 6-503-205-01 6-503-205-01 DIODE DIODE DIODE DIODE DIODE DA2J10100L RKZ5.1B2KGP1 RKZ6.8B2KGP1 RKZ6.8B2KGP1 RKZ6.8B2KGP1 < FERRITE BEAD > FB901 FB902 FB903 IC901 1-414-385-21 1-414-385-21 1-414-385-21 6-718-506-01 LED901 LED932 6-503-227-01 6-502-193-11 LED932 LED934 6-502-325-11 6-502-193-11 LED934 6-502-325-11 LED936 6-502-193-11 LED936 6-502-325-11 LED938 6-502-193-11 LSW905 1-798-283-11 < IC > LSW906 1-798-283-11 IC PT6587-LQ LSW906 1-798-287-11 < LED > LSW907 1-798-283-11 LED SML-D12V8WT86TN (SEEK+ > M) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (SEEK+ > M) (AEP, RU, UK) LED SML-D12V8WT86TN (ILLUMINATION) (EXCEPT AEP, RU, UK) Remark LED SML-D12P8WT86TK (ILLUMINATION) (AEP, RU, UK) LED SML-D12V8WT86TN (ILLUMINATION) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (ILLUMINATION) (AEP, RU, UK) LED SML-D12V8WT86TN (ILLUMINATION) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (ILLUMINATION) (AEP, RU, UK) LED SML-D12V8WT86TN (Z) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (Z) (AEP, RU, UK) LED SML-D12V8WT86TN (SOURCE/OFF) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (SOURCE/OFF) (AEP, RU, UK) LED SML-D12V8WT86TN (MODE) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (MODE) (AEP, RU, UK) LED SML-D12V8WT86TN ( ) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK ( ) (AEP, RU, UK) < SWITCH > INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD LED NESW505DT-A0-UV (LCD BACK LIGHT) LED SML-D12V8WT86TN ( ) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK ( ) (AEP, RU, UK) LED SML-D12V8WT86TN (m . SEEK –) (EXCEPT AEP, RU, UK) LED SML-D12P8WT86TK (m . SEEK –) (AEP, RU, UK) When indicating parts by reference number, please include the board name. Part No. < CAPACITOR > CN901 • SEMICONDUCTORS In each case, u: μ, for example: uA. . : μA. . , uPA. . , μPA. . , uPB. . : μPB. . , uPC. . , μPC. . , uPD. . : μPD. . • Abbreviation RU : Russian model LSW905 1-798-287-11 LSW907 1-798-287-11 LSW908 1-798-283-11 LSW908 1-798-287-11 LSW909 1-798-283-11 LSW909 1-798-287-11 LSW910 1-798-283-11 LSW910 1-798-287-11 TACTILE SWITCH (WITH LED) (DSPL/SCRL) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (DSPL/SCRL) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (6/PAUSE) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (6/PAUSE) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (5/ZAP) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (5/ZAP) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (4/SHUF) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (4/SHUF) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (3/REP) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (3/REP) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (2/ALBUM v) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (2/ALBUM v) (EXCEPT AEP, RU, UK) 5 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE KEY Ref. No. Part No. LSW911 1-798-283-11 LSW911 1-798-287-11 LSW912 1-798-283-11 LSW912 1-798-287-11 Description Remark TACTILE SWITCH (WITH LED) (1/ALBUM V) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (1/ALBUM V) (EXCEPT AEP, RU, UK) TACTILE SWITCH (WITH LED) (AF/TA/PTY) (AEP, RU, UK) TACTILE SWITCH (WITH LED) (PTY) (EXCEPT AEP, RU, UK) Ref. No. Part No. Description R952 1-216-822-11 METAL CHIP 1.2K Remark R954 1-216-814-11 METAL CHIP 270 R954 1-216-821-11 METAL CHIP 1K R956 1-216-814-11 METAL CHIP 270 R956 1-216-821-11 METAL CHIP 1K R958 1-216-814-11 METAL CHIP 270 R958 1-216-822-11 METAL CHIP 1.2K R961 R966 1-216-823-11 1-216-815-11 METAL CHIP METAL CHIP 1.5K 330 R966 1-216-821-11 METAL CHIP 1K R968 1-216-815-11 METAL CHIP 330 R968 1-216-822-11 METAL CHIP 1.2K R970 1-216-814-11 METAL CHIP 270 R970 1-216-821-11 METAL CHIP 1K R972 1-216-814-11 METAL CHIP 270 R972 1-216-821-11 METAL CHIP 1K R974 1-216-814-11 METAL CHIP 270 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) < TRANSISTOR > Q901 Q903 Q905 8-729-038-22 6-551-392-01 8-729-038-22 TRANSISTOR TRANSISTOR TRANSISTOR RT1N140C-TP-1 RT6N140C-TP-1 RT1N140C-TP-1 < RESISTOR > 6 R901 R902 R903 R904 R905 1-216-811-11 1-216-811-11 1-216-809-11 1-216-857-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP 150 150 100 1M 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R906 R907 R908 R909 R910 1-216-802-11 1-216-802-11 1-216-810-11 1-216-810-11 1-216-810-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 27 27 120 120 120 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R915 R916 R917 R918 R919 1-216-817-11 1-216-817-11 1-216-817-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP 470 470 470 0 0 5% 5% 5% 1/10W 1/10W 1/10W R920 R921 R922 R923 R924 1-216-820-11 1-216-821-11 1-216-821-11 1-216-822-11 1-216-823-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 820 1K 1K 1.2K 1.5K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R974 1-216-822-11 METAL CHIP 1.2K R976 R980 1-216-864-11 1-216-809-11 SHORT CHIP METAL CHIP 0 100 R925 R926 R927 R940 1-216-824-11 1-216-825-11 1-216-295-91 1-216-813-11 METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 1.8K 2.2K 0 220 5% 5% 1/10W 1/10W R980 1-216-811-11 METAL CHIP 150 R982 1-216-809-11 METAL CHIP 100 R982 1-216-811-11 METAL CHIP 150 R940 1-216-820-11 METAL CHIP 820 R984 1-216-809-11 METAL CHIP 100 R984 1-216-811-11 METAL CHIP 150 R986 1-216-809-11 METAL CHIP 100 R986 1-216-811-11 METAL CHIP 150 R988 1-216-811-11 METAL CHIP 150 R988 1-216-813-11 METAL CHIP 220 R990 1-216-812-11 METAL CHIP 180 R990 1-216-813-11 METAL CHIP 220 R991 R992 R993 R994 1-216-820-11 1-216-821-11 1-216-821-11 1-216-822-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 820 1K 1K 1.2K R995 1-216-823-11 METAL CHIP 1.5K R942 R944 1-216-864-11 1-216-813-11 SHORT CHIP METAL CHIP 0 220 R944 1-216-820-11 METAL CHIP 820 R946 1-216-814-11 METAL CHIP 270 R946 1-216-821-11 METAL CHIP 1K R948 1-216-815-11 METAL CHIP 330 R948 1-216-822-11 METAL CHIP 1.2K R950 1-216-814-11 METAL CHIP 270 R950 1-216-821-11 METAL CHIP 1K R952 1-216-815-11 METAL CHIP 330 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W (AEP, RU, UK) 5% 1/10W (EXCEPT AEP, RU, UK) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE KEY Ref. No. R996 R997 R998 R999 Part No. Description 1-216-824-11 1-216-825-11 1-216-821-11 1-216-295-91 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP Remark 1.8K 2.2K 1K 0 5% 5% 5% 1/10W 1/10W 1/10W < SWITCH > S901 S902 S903 S904 S905 1-798-284-11 1-798-284-11 1-798-284-11 1-798-284-11 1-798-284-11 TACTILE SWITCH (Z) TACTILE SWITCH (SOURCE/OFF) TACTILE SWITCH (SEEK+ > M) TACTILE SWITCH ( ) TACTILE SWITCH (m . SEEK –) S906 S907 1-798-284-11 1-798-284-11 TACTILE SWITCH ( ) TACTILE SWITCH (MODE) 7 CDX-GT40U/GT40UW/GT42UE/GT44U/GT45U/GT47UE REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1.0 2011.07 New 1.1 2011.08 Addition of CDX-GT42UE Addition of Korean model (CDX-GT45U) 1.2 2011.11 Addition of AEP and UK models (CDX-GT44U) Addition of Saudi Arabia model (CDX-GT45U) Addition of PRINTED WIRING BOARD – MAIN board for Saudi Arabia model – (SUPPLEMENT-1) 1.3 2012.06 Specification change of MG-101CA-188 Change of LCD driver IC (Ref. No. IC901), and change of other parts accompanying the change Change of KEY board (Suffix-21/-22) (SUPPLEMENT-2) 1.4 2012.07 (SMR-11052/11053) Changing parts supply classification of Ref. No. IC601 on the MAIN board Change of Part for Ref. No. D530, IC301, IC1300, L1300, Q401 to Q406, R402, R404, R407, R410, R421 and R423 on the MAIN board Change of Part No. for Ref. No. C1304, CN301, J1 and TU901 on the MAIN board Change of Part No. for Ref. No. X501 on the MAIN board (Except Saudi Arabia model) Deletion of Part for Ref. No. C741, C743, C745, CN501 and CN601 on the MAIN board Change of MAIN board (Suffix-22) (Except Saudi Arabia model) (SMR-12025)