GLOSSARY OF TERMS
Air Permeability
Commonly referred to as "porosity" it is the ease with which pressurized air can flow through a paper's
thickness. Typically measure by the Gurley or the Sheffield porosity tests, which measure the volumetric flow of
air through the paper thickness.
Standard Units: Gurley seconds (seconds / 100cc)
Burst Strength
The resistance of paper to rupture as measured by the hydrostatic pressure required to burst it when a
uniformly distributed and increasing pressure is applied to one of its side.
Standard Units: kPa
Burst Index (kPa m2/g) = Burst Strength (kPa) / Basis Weight (g/m2)
Coarseness
The weight of the fibre wall material per unit length of fibre.
Standard Units: mg/m or mg/100m
Contacts/fibre
Contacts/fiber means the average number of crossings between a fibre and others in the fibre network.
Fibre Length
The average contour length of all measured fibres in a given sample of pulp. This measurement can be
presented as the Length Weighted, Weight Weighted or Arithmetic Average fibre length.
Standard Units: mm
Fibre Shape
Fibre Curl Index is the ratio of actual fiber length to the distance between the 2 fiber ends minus 1. It gives in
indication of the continuous curvature of the fibers greater than 0.5 mm in length and within the selected range
limits.
Fibre Kink Index is the sum of the number of kinks (an abrupt change in fiber curvature) within a range of kink
angles divided by the total fiber length of all the fibers.
Mean Kink Angle is the average of all the kink angles greater than 20 degrees, divided by the total number of
detected kinks.
Fines
A measure of the portion of fibers which are shorter than a specified length, typically less than 0.2 mm.
Standard Units: %
Folding Endurance
The ability of paper to withstand repeated folding while held under tension before it severs at the crease.
Standard Units: number of double folds
Fracture Mechanics
Fracture toughness describes the ability of the material to resist the propagation of a pre-existing crack. It is
often determined as critical stress intensity factor, or sometimes referred to as tenacity. Fracture toughness
equals the geometric mean of fracture energy and elastic modulus.
Fracture energy means the critical energy release rate, where the pre-existing crack starts to propagate with an
infinitesimal increment of applied tension when the energy release rate reaches.
Freeness / Wetness
Terms used to define how quickly or slowly water is drained from the pulp. The opposite of freeness is
slowness. Freeness or slowness is a function of degree of beating or refining on pulp.
Standard Units:
Canadian Standard Freeness: ml CSF
Schopper Riegler: degree SR
Kappa Number
Kappa number is a measure of lignin content in the pulp. The kappa number is the volume (in milliliters) of 0.1N
potassium permanganate solution consumed by one gram of moisture-free pulp under the conditions specified
in this method. The results are corrected to 50% consumption of the permanganate added.
Premium Reinforcement Pulps (PRP)
It is increasingly common to hear papermakers referring to those NBSK pulps that deliver the highest
reinforcement as "PRPs" or "Premium Reinforcement Pulps". These are pulps which have intrinsic
morphological advantages that position their tensile and fracture properties at the extreme high end of the
range of NBSK pulps.
Reinforcement Potential
The main use of softwood kraft pulps is to strengthen weaker paper-making furnishes without significantly
impairing other end-use properties. This function is referred to as reinforcement.
Reinforcement potential is a complex pulp property and measurement usually involves consideration of the
grade of paper to be reinforced. Currently there is no generally accepted single method for measuring
reinforcement potential that applies to all paper grades.
For LWC grades, one commonly accepted definition is that reinforcement potential is proportional to the
average fiber length and tear strength at 70 Nm/g tensile index and inversely proportional to fiber coarseness.
For SC papers the reinforcement potential has been theorized to be described simply by the ratio of fibre length
to coarseness.
Specific Energy Input
Net energy applied in a refiner per unit weight of pulp on oven dry basis during refining.
Standard Units: kW h / t
Other Units: hpday / ton
Other Units: GWs / kg
1 kWh/ton = 17.9 hpday/ton = 3.6 GWs/kg
Stretch
A measure of the maximum tensile strain developed in the sample strip before rupture.
The stretch or percentage elongation is expressed as a percentage.
Standard Units: %
T.E.A.
The work done when a paper specimen is stressed to rupture in tension under prescribed conditions as
measured by the integral of tensile strength over the range of tensile strain from 0 to maximum. T.E.A is highly
dependant on maximum tensile strength and sheet stretch.
Standard Units: J/kg
Tear Resistance / Tear Strength
The mean force required to continue the tearing of paper from an initial cut under standardized conditions.
Because it takes more force to start a tear than to continue one already started, 1 or 2 small cuts are made in
the edge of the paper prior to testing. The most common type of testers utilize a pendulum device where the
difference between the height the pendulum swings upon tearing the paper, and that to which it would have
swung had there been no paper, is a measure of the force taken to tear the paper. Standard instrument used
for measuring tear resistance are the "Elmendorf tester" and the "Brecht-Imset tester."
Standard Units:
Tear Resistance: mN
Tear index (mN m2/g) = Tearing Resistance (mN) / Basis Weight (g/m2)
Tensile Stiffness
Tensile stiffness of paper is the slope of the tangent of the tensile strength-strain curve at the point of zero
strain. The tensile stiffness (in N/m of width) is equal to the elastic modulus multiplied by the paper thickness.
When the tensile stiffness is divided by the grammage, it is called the tensile stiffness index (Nm/kg), which
numerically equals the specific elastic modulus (in Nm/kg).
Standard Units:
Tensile Stiffness: N/m
Tensile Stiffness Index: (Nm/kg)
Tensile Strength
Tensile is measured by clamping a strip of paper, typically 15 mm wide, between the 2 jaws of a tensile tester,
which then slowly move in opposite directions until the strip breaks. The tensile strength is the tensile force
when the strip ruptures. It is a guide to the performance of paper when subjected to tensional pulling forces on
a papermachine, printing press or converting equipment.
Tensile Breaking Length measures the length of the sample strip that will break, under its own weight. It can be
calculated from Tensile Strength according to:
Breaking length (km) = Tensile Strength (N) / Sample width (m) × Grammage (g/m2) × 9.807
Standard Units:
Tensile Strength: N/m
Tensile Breaking Length: km
Tensile index (Nm/g) = tensile strength (N/m) / basis weight (g/m2)
Zero Span Tensile Strength (Wet and Dry)
The zero-span tensile test is similar to the normal tensile test, but the clamping jaws are situated with no gap
(Zero Span). Clamping in this manner virtually eliminates the opportunity for inter-fibre bonds to break, resulting
in the measurement of the tensile force required to break individual fibers.
Standard Units: km
0
