CHAPTER EXERCISES
Exercise 7.2 Rod Support*
Exercise 7.3 Tailstock*
Exercise 7.4 Bearing*
Exercise 7.5 Holder Clip*
Exercise 7.6 Cam*
Exercise 7.7 Index Arm*
*
309
Sketch or draw necessary views. These exercises are designed to fit on 8.5″ × 11″ A-size or A4 metric size paper. Use a title block or title strip as assigned by
your instructor. If dimensions are required, study Chapter 11 and use metric or decimal-inch dimensions as assigned by your instructor. Move dimensions to
better locations where possible.
310
CHAPTER 7
2D DRAWING REPRESENTATION
METRIC
METRIC
Exercise 7.8 Roller Lever*
Exercise 7.9 Support*
Exercise 7.10 Locating Finger*
Exercise 7.11 Toggle Lever*
METRIC
Exercise 7.12 Cut-off Holder*
*
Exercise 7.13 Index Slide*
Sketch or draw necessary views. These exercises are designed to fit on 8.5″ × 11″ A-size or A4 metric size paper. Use a title block or title strip as assigned by
your instructor. If dimensions are required, study Chapter 11 and use metric or decimal-inch dimensions as assigned by your instructor. Move dimensions to
better locations where possible.
CHAPTER EXERCISES
Exercise 7.14 Frame Guide*
Exercise 7.15 Chuck Jaw*
Exercise 7.17 Tool Holder.* Given: Front and left-side
views. Required: Front, top, and right-side views.
Exercise 7.16 Hinge Bracket.* Given: Front and bottom
views. Required: Front, top, and right-side views.
Exercise 7.19 Cross-feed Stop*
*
Exercise 7.18 Shifter Block.* Given: Front and left-side
views. Required: Front, top, and right-side views.
Sketch or draw necessary views. These exercises are designed to fit on
8.5″ × 11″ A-size or A4 metric size paper. Use a title block or title strip as
assigned by your instructor. If dimensions are required, study Chapter 11
and use metric or decimal-inch dimensions as assigned by your instructor.
Move dimensions to better locations where possible.
311
312
CHAPTER 7
2D DRAWING REPRESENTATION
Exercise 7.20 Cross Cam.* Given: Front and left-side views.
Required: Front, top, and right-side views.
Exercise 7.21 Roller Stud*
Exercise 7.23 Feed Rod Bearing*
Exercise 7.22 Hinge Block*
Exercise 7.24 Lever Hub.* Draw half size.
*
Exercise 7.25 Vibrator Arm*
Sketch or draw necessary views. These exercises are designed to fit on 8.5″ × 11″ A-size or A4 metric size paper. Use a title block or title strip as assigned by
your instructor. If dimensions are required, study Chapter 11 and use metric or decimal-inch dimensions as assigned by your instructor. Move dimensions to
better locations where possible.
CHAPTER EXERCISES
Exercise 7.26 Clutch Lever*
313
Exercise 7.27 Counter Bearing Bracket.* Draw half size.
Exercise 7.29 Control Block*
Exercise 7.28 Tool Holder*
Exercise 7.30 Socket Bearing*
*
Exercise 7.31 Tool Holder*
Sketch or draw necessary views. These exercises are designed to fit on 8.5″ × 11″ A-size or A4 metric size paper. Use a title block or title strip as assigned by your
instructor. If dimensions are required, study Chapter 11 and use metric or decimal-inch dimensions as assigned by your instructor. Move dimensions to better locations where possible.
314
CHAPTER 7
2D DRAWING REPRESENTATION
Exercise 7.32 Locating V-Block*
Exercise 7.33 Anchor Bracket*
Exercise 7.34 Lead Screw Bracket.** Draw half size.
Exercise 7.35 Lever Bracket.** Draw half size.
**
Sketch or draw necessary views. Larger and more detailed parts show the details more clearly when drawn on larger sheet sizes. Consider using B, C, or A3 or
A2 sheets. Use a title block or title strip as assigned by your instructor. If dimensions are required, study Chapter 11 and use metric or decimal-inch dimensions
as assigned by your instructor. Move dimensions to better locations where possible.
CHAPTER EXERCISES
315
SF
Exercise 7.36 Gripper Rod Center*
Exercise 7.37 Bearing Bracket*
*
Exercise 7.38 Link Arm Connector.* Draw one-quarter size.
Sketch or draw necessary views. Larger and more detailed parts show the details more clearly when drawn on larger sheet sizes. Consider using B, C, or A3 or
A2 sheets. Use a title block or title strip as assigned by your instructor. If dimensions are required, study Chapter 11 and use metric or decimal-inch dimensions
as assigned by your instructor. Move dimensions to better locations where possible.
316
CHAPTER 7
2D DRAWING REPRESENTATION
Exercise 7.39 Mounting Bracket*
Exercise 7.40 LH Shifter Fork*
Exercise 7.41 Gear Shift Bracket*
Exercise 7.42 Fixture Base*
*
Sketch or draw necessary views. Larger and more detailed parts show the details more clearly when drawn on larger sheet sizes. Consider using B, C, or A3 or
A2 sheets. Use a title block or title strip as assigned by your instructor. If dimensions are required, study Chapter 11 and use metric or decimal-inch dimensions
as assigned by your instructor. Move dimensions to better locations where possible.
CHAPTER EXERCISES
Exercise 7.43 Ejector Base.* Draw half size.
Exercise 7.44 Tension Bracket*
Exercise 7.45 Offset Bearing*
Exercise 7.46 Feed Guide*
*
317
Sketch or draw necessary views. Larger and more detailed parts show the details more clearly when drawn on larger sheet sizes. Consider using B, C, or A3 or
A2 sheets. Use a title block or title strip as assigned by your instructor. If dimensions are required, study Chapter 11 and use metric or decimal-inch dimensions
as assigned by your instructor. Move dimensions to better locations where possible.
0
