V D E SERIES POWER ENTRY MODULE EMI FILTERS INTRODUCTIONS SPECIFICATIONS 1. Power module incorporates an IEC connector, a fuse holder with optional power on/off switch and voltage selector switch, plus an EMI filter all-in-one single, easy-to-install unit. 2. Fuse holder designed for one IEC 5x20mm fuse. Safety interlock prevents fuse removal with line plug inserted (Use only with 250V fuse). 3. All part numbers are UL recognized, CSA certified and VDE approved. 4. Switch electrical lifetime: 10,000 cycles. Maximum inrush current: 70A. 1. Maximum leakage current each line-to-ground @ 115VAC 60Hz: 0.25mA @ 250VAC 50Hz: 0.45mA 2. Hipot rating (one minute) line-to-ground: 2250VDC line-to-line: 1450VDC 3. Operating frequency: 50/60Hz 4. Rated voltage: 115/250VAC MINIMUM INSERTION LOSS IN dB CURRENT RATING 3A 6A 3A 6A COMMON MODE (L-G) IN 50 OHM SYSTEM FREQUENCY-MHz .15 .50 1.0 5.0 10 30 35 40 35 35 16 25 30 42 45 DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM 10 40 45 45 45 6 25 30 42 45 30 35 40 35 40 DELTA PART NO. 115VAC RATED CURRENT 250VAC IEC CONNECTOR FUSE HOLDER POWER SWITCH VOLTAGE SELECTOR SW ELECTRICAL SCHEMATIC AK1 6A 6A FIG. A AK2 6A 6A AK2D 6A 4A AK3 6A 6A AK3D 6A 4A AK4 6A 6A AK5 6A 6A SP1 DP2 SP1 REAR3 FIG. A DP2 REAR3 FIG. B REAR3 FIG. A FRONT4 FIG. C FIG. A 1. Single-pole UL, CSA & VDE approved Current rating: UL & CSA-6A both at 125VAC & 250VAC; VDE-6A at 250VAC. 2. Double-pole UL CSA & VDE approved Current rating: UL & CSA-6A at 125VAC, 4A at 250VAC; VDE-4A at 250VAC. FIG. B 3. Voltage selector SW -UL, CSA & VDE approved Current rating: 10A at 125VAC; 5A at 250VAC. 4. Voltage selector SW -UL, CSA & VDE approved Current rating: UL & CSA-6A both at 125VAC & 250VAC; VDE-6A at 250VAC. ELECTRICAL SCHEMATIC AK3/4 ONLY AK1/4 WITHOUT POWER SW F SW L' Cy L I N E C1 R L Cy N G F L I N E L C2 O A D F L' Cy C1 R L Cy N G N' L 110V O A 220V D L C2 O A D N' G' FIG. B 4-1 1 110V 2 110V 3 220V 110V 4 FIG. C For transformers with two separate windings L L I N E C2 G' AK3D ONLY SW C1 Cy N G N' R Cy L G' FIG. A SW L' L L POWER ENTRY MODULE FILTERS TYPE & RATED CURRENT Suggested thickness of mounting panel is from 0.04 to 0.07 inch Suggested mounting cutout 27.0 1.063 0.003 R0.04Max. 1.0 2.6 0.003 66.0 MECHANICAL CONSTRUCTION L 1.059 26.9 220 1.15 29.2 G 110 N L 1 G 2 4 3 N 0.57 0.43 AK5 10.9 2.17 55.1 2.24 56.9 14.48 2.65 67.3 2.57 65.3 2.65 67.3 L N G 1.059 26.9 1.15 29.2 N I L 2.17 55.1 2.38 60.5 O G AK2,AK2D 2.57 65.3 O G I L 2.60 66.0 N G 0.65 16.5 115V AK3,AK3D AK4 (without power switch) 1.059 26.9 1.15 29.2 2.65 67.3 G N L 2.17 55.1 2.24 56.9 POWER ENTRY MODULE FILTERS 1.15 29.2 2.65 67.3 G AK1 2.57 65.3 4-2 1.059 26.9 UNIT: INCH mm