Introduction Welcome to Fivalco, the industry’s most trusted brand for Our products are design tested and certified by the leading professionals. With history over 30 years, Fivalco has been an testing agencies, including Underwriters Laboratories and inventor and leading manufacturer of superior flow control Factory Mutual, based on a wide range of global standards. products. Today, with manufacturing and distribution facilities Fivalco also has been approved by many local jurisdictions in Asia, America, and Europe our products and services reach including California Fire Marshal. over 80 countries and millions of people worldwide. The success of our company is based on listening to our Fivalco’s legacy starts with innovative engineering and superior customers, understanding their needs and developing construction, built upon proven science and cutting-edge products and services that meet or exceed their requirements. technology. Commitment to quality and performance are at We work in a collaborative manner with our customers to the top of our agenda. From start to finish, and design to develop innovative and effective solutions. construction, every piece is built to perfection. Our customer service and technical support are recognized as Each valve is pressure tested at 4 times the working pressure second to none. Our extensive inventory and swift shipments and must pass a cycling test of 1000 open/shut operations enhance customers’ competitive edge. We aim for excellence without failure of any part or component. As an ISO registered in everything we do. manufacturer, we utilize Quality Production System to drive our commitment to continuous improvement. Manufacturing Facility (Yeoju, S. Korea) U.S.A. Office (Anaheim, CA) U.S.A. Warehouse (Anaheim, CA) 1 www.fivalcoinc.com Contents BT Bronze Butterfly Valve 175 PSI Threaded Ends 4 BG Bronze Butterfly Valve 175 PSI Grooved Ends 5 HPG Butterfly Valve 300 PSI Grooved Ends 6 HPW Butterfly Valve 300 PSI Wafer Ends 7 HPGT Butterfly Valve 300 PSI Tapped Body 8 DG Butterfly Valve 175 PSI Grooved Ends 9 DW Butterfly Valve 175 PSI Wafer Ends 10 8100 Lever Handle Butterfly Valve 11 8200 Lever Lock Butterfly Valve 12 DGC Swing Check Valve Grooved Ends 14-15 5201-300-FLA Swing Check Valve Flanged Ends 16 3299-300-FLA OS&Y Gate Valve 300 PSI Flanged Ends 17 3299-300-FG OS&Y Gate Valve 300 PSI Flanged x Grooved Ends 18 3299-300-GG OS&Y Gate Valve 300 PSI Grooved x Grooved Ends 19 3288-300-FLA NRS Gate Valve 300 PSI Flanged Ends 20 3288-300-FG NRS Gate Valve 300 PSI Flanged x Grooved Ends 21 3288-300-GG NRS Gate Valve 300 PSI Grooved / Grooved Ends 22 IP0888 WP0999 FXB / FXU Firelet 23-24 Indicator Post: Adjustable Type Indicator Post: Wall Type 25 Flexible Sprinkler Connector Braided / Unbraided 26 Welded Pipe Outlets 27 2 www.fivalcoinc.com Illustrated Product Index Bronze Butterfly Valve Threaded UL, ULC, FM, CA Fire Marshal 175 PSI Bronze Butterfly Valve Grooved UL, ULC, FM, CA Fire Marshal 175 PSI Butterfly Valve Grooved UL,, ULC, FM, CA Fire Marshal M 300 PSI Butterfly Valve Wafer UL, L, ULC, FM, CA Fire Marshal Mar 300 PSI Butterfly Valve Tapped UL, L, ULC, FM, CA Fire Marshal Ma 300 PSI BT Sizes 1” thru 2-1/2” Page 4 BG Sizes 2” thru 2-1/2” Page 5 HPG Sizes 2-1/2” thru 8” Page 6 HPW Sizes 2-1/2” thru 8” Page 7 HPGT Sizes 2-1/2” thru 8” Page 8 Butterfly Valve Grooved UL, ULC, FM, CA Fire Marshal Mar 175 PSI Butterfly Valve Wafer UL, ULC, FM, CA Fire Marshal Mars 175 PSI Lever Handle Butterfly Valve Grooved 200 PSI Lever Lock Butterfly Valve Grooved & Wafer 300 PSI Check Valve Grooved UL, ULC, FM 300 PSI DG Sizes 2-1/2” thru 8 Page 9 DW Sizes 2-1/2” /2” 2 thru 2” th 8”” Page 10 8100 Sizes 2” thru 8” Page 11 8200 Sizes 2” thru 8” Page 12 DGC Sizes 2” thru 8” Page 14 - 15 Check Valve Flanged UL, ULC, FM 300 PSI OS&Y Gate Valve Flanged UL, ULC, FM 300 PSI OS&Y Gate Valve Flanged x Grooved UL, ULC, FM 300 PSI OS&Y Gate Valve Grooved x Grooved UL, ULC, FM 300 PSI NRS Gate Valve Flanged UL, ULC, FM 300 PSI 5201-300-FLA Sizes 2-1/2” thru 12” Page 16 3299-300-FLA Sizes 2-1/2” thru 12” Page 17 3299-300-FG Sizes 2-1/2” thru 12” Page 18 3299-300-GG Sizes 2-1/2” thru 12” Page 19 3288-300-FLA Sizes 2-1/2” thru 12” Page 20 NRS Gate Valve Flanged x Grooved UL, ULC, FM 300 PSI NRS Gate Valve Grooved x Grooved UL, ULC, FM 300 PSI Indicator Post Adjustable Type UL, ULC,FM Indicator Post Wall Type UL, ULC,FM Flexible Sprinkler Connector Braided & Unbraided UL, ULC, FM 175 PSI 3288-300-FG Sizes 2-1/2” thru 12” Page 21 3288-300-GG Sizes 2-1/2” thru 12” Page 22 IP0888 WP0999 Page 23 - 24 Page 25 FXB / FXU Sizes 24” thru 72” Page 26 Welded Pipe Outlets Threaded UL, ULC, FM 300 PSI Firelet Sizes 1/2” thru 2-1/2” Page 27 3 www.fivalcoinc.com Model: BT Bronze Butterfly Valve | Threaded Technical Features t Connections: Threaded ends (ANSI / ASME B1.20.1 NPT) t Sizes: 1”, 1-1/4”, 1-1/2”, 2”, 2-1/2” tApprovals: UL, ULC, FM, and California State Fire Marshal 50 PSI) t Maximum Working Pressure: 175 PSI (Max. Test Pressure: 350 t Maximum Working Temperature: 250˚F (120˚C) tApplication: Indoor and Outdoor Use t'BDUPSZ*OTUBMMFE4VQFSWJTPSZ5BNQFS4XJUDI"TTFNCMZ Component Material Specification #PEZ Bronze ASTM B505 Disc Aluminum Bronze ASTM B548 %JTD&ODBQTVMBUJPO &1%.3VCCFS ASTM D2000 Indicator Brass ASTM B16 Housing Steel ASTM A619 Handwheel Steel ASTM A619 Stem Stainless Steel "45."5ZQF9. 4UBJOMFTT4UFFMCPEZBWBJMBCMFVQPOSFRVFTU Firefly® Model: BT Dimensions: Inches (Millimeters) Size in/mm A B C D E 1” 1.7 (43.7) 1.6 (39.7) 2.1 (54) 2.0 (52) 1.5 (37) 1-1/4” 2.1 (54) 1.9 (49) 2.6 (67) 2.2 (56) 1.6 (41) 1-1/2” 2.4 (60) 2.2 (56) 2.9 (73) 2.3 (59) 1.7 (43) 2” 3.0 (76) 2.8 (70) 3.2 (82.4) 2.5 (64) 1.9 (49) 2-1/2” 3.5 (90) 3.3 (84) 4.1 (104) 2.9 (74) 2.3 (59) 4 www.fivalcoinc.com Model: BG Bronze Butterfly Valve | Grooved Technical Features t Connections: Grooved Ends (AWWA C606) t Sizes: 2”, 2-1/2” tApprovals: UL, ULC, FM, and California State Fire Marshal t Maximum Working Pressure: 175 PSI (Max. Test Pressure: 350 PSI) t Maximum Working Temperature: 250˚F (120˚C) tApplication: Indoor and Outdoor Use t'BDUPSZ*OTUBMMFE4VQFSWJTPSZ5BNQFS4XJUDI"TTFNCMZ Component Material Specification #PEZ Bronze ASTM B505 Disc Aluminum Bronze ASTM B548 %JTD&ODBQTVMBUJPO &1%.3VCCFS ASTM D2000 Indicator Brass ASTM B16 Housing Steel ASTM A619 Handwheel Steel ASTM A619 Stem Stainless Steel "45."5ZQF9. 4UBJOMFTT4UFFMCPEZBWBJMBCMFVQPOSFRVFTU FireFly® Model: BG Dimensions: Inches (Millimeters) Size in/mm A B C D E F G 2” 4.5 (114) 2.4 (60.3) 2.3 (57.15) 0.6 (16) 0.3 (8) 1.9 (49) 2.5 (64) 2-1/2” 4.5 (114) 3.0 (75) 2.7 (69.1) 0.6 (16) 0.3 (8) 2.3 (59) 2.9 (74) 5 www.fivalcoinc.com Model: HPG 300 PSI Butterfly Valve | Grooved Technical Features t Connections: Grooved ends, AWWA C606 t Sizes: 2-1/2”, 3”, 4”, 6”, 8” tApprovals: UL, ULC, FM, and California State Fire Marshal t Maximum Working Pressure: 300 PSI (Max. Test Pressure: 600 PSI) t Maximum Working Temperature: 250˚F (120˚C) tApplication: Indoor and Outdoor Use tDouble-Seal Disc; Resilient EPDM Coating t'BDUPSZ*OTUBMMFE4VQFSWJTPSZ5BNQFS4XJUDI"TTFNCMZ Component Material Specification Body Ductile Iron ASTM A536 Nylon-11 Coated Disc Ductile Iron ASTM A536 EPDM Encapsulated Indicator Ductile Iron ASTM A536 Housing Ductile Iron ASTM A536 Handwheel Ductile Iron ASTM A536 Stem Stainless Steel AISI 420 Worm Shaft Stainless Steel AISI 410 Shear Pin Steel ASTM A510 Gear Segment Brass ASTM B584 Housing Gasket EPDM EPDM Grade E O-Ring (AII) EPDM EPDM Grade E Fireriser® Model: HPG Dimensions: Inches (Millimeters) Size in/mm A B C D E F G 2-1/2” 4.1 (105) 3.7 (95) 3.8 (96.4) 2.9 (73) 5.3 (135) 5.3 (135) 5.0 (128) 3” 4.4 (112) 3.6 (92) 3.8 (96.4) 3.5 (88.9) 5.6 (142) 5.3 (135) 5.0 (128) 4” 5.7 (145) 4.3 (108) 4.5 (115.4) 4.5 (114.3) 6.9 (175) 5.3 (135) 5.0 (128) 6” 7.0 (179) 5.7 (146) 5.2 (132.4) 6.6 (168) 8.2 (209) 7.6 (193) 8.7 (220) 0.3 (6.8) 8” 8.0 (204) 6.7 (170) 5.8 (147.4) 8.6 (219.1) 9.2 (234) 7.6 (193) 8.7 (220) 1.0 (24.2) H H: Disc clearance of body surface through end of disc in open position. 6 www.fivalcoinc.com Model: HPW 300 PSI Butterfly Valve | Wafer Technical Features t Connections: Wafer ends, ANSI Class 125 t Sizes: 2-1/2”, 3”, 4”, 6”, 8” tApprovals: UL, ULC, FM, and California State Fire Marshal t Maximum Working Pressure: 300 PSI (Max. Test Pressure: 600 PSI) t Maximum Working Temperature: 250˚F (120˚C) tApplication: Indoor and Outdoor Use tDouble-Seal Disc; Resilient EPDM Coating t'BDUPSZ*OTUBMMFE4VQFSWJTPSZ5BNQFS4XJUDI"TTFNCMZ Material Specification #PEZ Ductile Iron "45."/ZMPO$PBUFE Disc Ductile Iron "45."&1%.&ODBQTVMBUFE Indicator Ductile Iron ASTM A536 Housing Ductile Iron ASTM A536 Handwheel Ductile Iron ASTM A536 Stem Stainless Steel AISI 420 Worm Shaft Stainless Steel AISI 410 Shear Pin Steel ASTM A510 Gear Segment Brass ASTM B584 Housing Gasket EPDM EPDM Grade E O-Ring (AII) EPDM EPDM Grade E Component Fireriser® Model: HPW Dimensions: Inches (Millimeters) Size in/mm A B C D E F G H 2-1/2” 5.4 (136) 3.4 (87) 1.8 (46) 5.9 (149.4) 6.5 (166) 5.3 (135) 5.0 (128) 0.3 (8.2) 3” 5.6 (143) 3.7 (93) 1.8 (46) 6.6 (168.2) 6.8 (173) 5.3 (135) 5.0 (128) 0.6 (14.5) 4” 6.1 (156) 4.3 (109) 2.0 (52) 7.9 (200.2) 7.3 (186) 5.3 (135) 5.0 (128) 0.9 (22.7) 6” 7.4 (188) 5.7 (144) 2.2 (56) 10.6 (269.8) 8.6 (218) 7.6 (193) 8.7 (220) 1.8 (45.4) 8” 8.7 (222) 6.5 (166) 2.3 (58) 13.0 (330.2) 9.9 (252) 7.6 (193) 8.7 (220) 2.7 (69.1) )%JTDDMFBSBODFPGCPEZTVSGBDFUISPVHIFOEPGEJTDJOPQFOQPTJUJPO 7 www.fivalcoinc.com Model: HPGT 300 PSI Butterfly Valve | Tapped Body Technical Features t Connections: Groove Tap Body, AWWA C606 t Sizes: 2-1/2”, 3”, 4”, 6”, 8” tApprovals: UL, ULC, FM, and California State Fire Marshal t Maximum Working Pressure: 300 PSI (Max. Test Pressure: 600 PSI) t Maximum Working Temperature: 250˚F (120˚C) tApplication: Indoor and Outdoor Use tDouble-Seal Disc; Resilient EPDM Coating t'BDUPSZ*OTUBMMFE4VQFSWJTPSZ5BNQFS4XJUDI"TTFNCMZ Component Material Specification Body Ductile Iron ASTM A536 Nylon-11 Coated Disc Ductile Iron ASTM A536 EPDM Encapsulated Indicator Ductile Iron ASTM A536 Housing Ductile Iron ASTM A536 Handwheel Ductile Iron ASTM A536 Stem Stainless Steel AISI 420 Worm Shaft Stainless Steel AISI 410 Shear Pin Steel ASTM A510 Gear Segment Brass ASTM B584 Housing Gasket EPDM EPDM Grade E O-Ring (AII) EPDM EPDM Grade E Fireriser® Model: HPGT Dimensions: Inches (Millimeters) Size in/mm A B C D E F 2-1/2” 4.1 (105) 5.0 (127) 5.3 (135) 2.9 (73) 5.3 (135) 5.0 (128) 3” 4.4 (112) 5.0 (127) 5.3 (135) 3.5 (88.9) 5.6 (142) 4” 5.7 (145) 5.0 (127) 5.3 (135) 4.5 (114.3) 6.9 (175) 6” 7.0 (179) 5.6 (143.5) 7.6 (193) 6.6 (168.3) 8.2 (209) 8.7 (220) 8” 8.0 (204) 6.0 (152.4) 7.6 (193) 8.6 (219.1) 9.2 (234) 8.7 (220) H N M 1.2 (30) 0.5 (13) 4-1/2-14NPT 5.0 (128) 1.2 (30) 0.5 (13) 4-1/2-14NPT 5.0 (128) 1.6 (40.4) 0.6 (15) 4-3/4-14NPT 0.3 (6.8) 1.6 (40.4) 0.6 (15) 4-3/4-14NPT 1.0 (24.2) 1.6 (40.4) 0.6 (15) 4-3/4-14NPT G (%JTDDMFBSBODFPGCPEZTVSGBDFUISPVHIFOEPGEJTDJOPQFOQPTJUJPO 8 www.fivalcoinc.com Model: DG 175 PSI Butterfly Valve | Grooved Technical Features t Connections: Grooved Ends, AWWA C606 t Sizes: 2-1/2”, 3”, 4”, 6”, 8” tApprovals: UL, ULC, FM, and California State Fire Marshal t Maximum Working Pressure: 175 PSI (Max. Test Pressure: 350 PSI) t Maximum Working Temperature: 250˚F (120˚C) tApplication: Indoor and Outdoor Use t'BDUPSZ*OTUBMMFE4VQFSWJTPSZ5BNQFS4XJUDI"TTFNCMZ Component Material Specification #PEZ Ductile Iron "45."/ZMPO$PBUFE Disc Ductile Iron "45."&1%.&ODBQTVMBUFE Indicator Ductile Iron ASTM A536 Housing Ductile Iron ASTM A536 Handwheel Ductile Iron ASTM A536 Stem Stainless Steel AISI 420 Worm Shaft Stainless Steel AISI 410 Shear Pin Steel ASTM A510 Gear Segment Brass ASTM B584 Housing Gasket EPDM EPDM Grade E O-Ring (All) EPDM EPDM Grade E Fireriser® Model: DG Dimensions: Inches (Millimeters) Size: in / mm A B C D E F G 2 1/2” 4.1 (105) 3.7 (9) 3.8(96.4) 2.9 (73) 5.3 (135) 5.3 (135) 5.0 (128) 3” 4.4 (112) 3.6 (92) 3.8(96.4) 3.5 (88.9) 5.6 (142) 5.3 (135) 5.0 (128) 4” 5.7 (145) 4.3 (108) 4.5 (115.4) 4.5 (114.3) 6.9 (175) 5.3 (135) 5.0 (128) 6” 7.0 (179) 5.7 (146) 5.2 (132.4) 6.6 (168) 8.2 (209) 7.6 (193) 8.7 (220) 0.3 (6.8) 8” 8.0 (204) 6.7 (170) 5.8 (147.4) 8.6 (219.1) 9.2 (234) 7.6 (193) 8.7 (220) 1.0 (24.2) H )%JTDDMFBSBODFPGCPEZTVSGBDFUISPVHIFOEPGEJTDJOPQFOQPTJUJPO 9 www.fivalcoinc.com Model: DW 175 PSI Butterfly Valve | Wafer Technical Features t Connections: Wafer Ends, ANSI Class 125 t Sizes: 2-1/2”, 3”, 4”, 6”, 8” tApprovals: UL, ULC, FM, and California State Fire Marshal t Maximum Working Pressure: 175 PSI (Max. Test Pressure: 350 PSI) t Maximum Working Temperature: 250˚F (120˚C) tApplication: Indoor and Outdoor Use t'BDUPSZ*OTUBMMFE4VQFSWJTPSZ5BNQFS4XJUDI"TTFNCMZ Component Material Specification #PEZ Ductile Iron "45."/ZMPO$PBUFE Disc Ductile Iron "45."&1%.&ODBQTVMBUFE Indicator Ductile Iron ASTM A536 )PVTJOH Ductile Iron ASTM A536 Handwheel Ductile Iron ASTM A536 Stem Stainless Steel AISI 420 Worm Shaft Stainless Steel AISI 410 Shear Pin Steel ASTM A510 (FBS4FHNFOU Brass ASTM B584 )PVTJOH(BTLFU EPDM EPDM Grade E 03JOH "** EPDM EPDM Grade E Fireriser® Model: DW Dimensions: Inches (Millimeters) Size in/mm A B C D E F G H 2 1/2” 5.4 (136) 3.4 (87) 1.8 (46) 5.9 (149.4) 6.5 (166) 5.3 (135) 5.0 (128) 0.3 (8.2) 3” 5.6 (143) 3.7 (93) 1.8 (46) 6.6 (168.2) 6.8 (173) 5.3 (135) 5.0 (128) 0.6 (14.5) 4” 6.1 (156) 4.3 (109) 2.0 (52) 7.9 (200.2) 7.3 (186) 5.3 (135) 5.0 (128) 0.9 (22.7) 6” 7.4 (188) 5.7 (144) 2.2 (56) 10.6 (269.8) 8.6 (218) 7.6 (193) 8.7 (220) 1.8 (45.4) 8” 8.7 (222) 6.5 (166) 2.3 (58) 13.0 (330.2) 9.9 (252) 7.6 (193) 8.7 (220) 2.7 (69.1) )%JTDDMFBSBODFPGCPEZTVSGBDFUISPVHIFOEPGEJTDJOPQFOQPTJUJPO 10 www.fivalcoinc.com Model: 8100 Lever Handle Butterfly Valve | Grooved Technical Features t Connections: Grooved Ends (AWWA C606) t Sizes: 2”, 2-1/2”, 3”, 4”, 6”, 8” t Maximum Working Pressure: 200 PSI (Max. Test Pressure: 350 PSI) t Maximum Working Temperature: 250˚F (120˚C) tApplication: Indoor and Outdoor Use Component Material Body Ductile Iron, Epoxy Coated Disc Ductile Iron, EPDM or NBR Encapsulated Stem Stainless Steel Latch Plate Steel, Zinc Plated Handle Carbon Steel, Epoxy Coating or Casting Model: 8100 Dimensions: Inches (Millimeters) Size A B C D E F G 2” 2.4 (60.3) 2.3 (57.2) 3.4 (87.4) 0.6 (15.9) 0.3 (8.7) 6 (152.4) 1 (25.4) 2-1/2” 2.9 (74.2) 2.8 (70.2) 3.8 (96.8) 0.6 (15.9) 0.4 (8.9) 6 (152.4) 3” 3.6 (90.3) 3.4 (86.4) 3.8 (96.8) 0.6 (15.9) 0.4 (8.9) 4” 4.6 (116.1) 4.4 (111.8) 4.6 (117.3) 0.6 (15.9) 6” 6.7 (171) 6.6 (166.6) 5.3 (133.4) 8” 8.6 (219.2) 8.4 (214.4) 5.8 (147) K L 1.8 (46.0) 2 (50.8) 3.2 (81) 1 (25.4) 2.1 (52.3) 2.4 (62) 3.6 (91.9) 8.4 (214.4) 1 (25.4) 2.6 (66.5) 2.7 (68.1) 4.3 (108) 0.4 (8.9) 8.4 (214.4) 1 (25.4) 3.3 (84.1) 3.3 (84.1) 4.9 (125.5) 0.6 (15.9) 0.4 (8.9) 12.3 (311.2) 1.3 (31.8) 4.4 (111.3) 4.4 (111.3) 7 (177.8) 0.7 (19) 0.4 (11) 12.3 (311.2) 1.3 (31.8) 5.4 (137) 5.4 (137) 8 (202) 11 H www.fivalcoinc.com Model: 8200 Lever Lock | Grooved / Wafer Technical Features t Connections: Grooved Ends (AWWA C606), Wafer Type (ANSI Class125) t1PTJUJPO-FWFS-PDL)BOEMF t Sizes: 2”, w w w w w 14* t Maximum Working Pressure: 14* .BY5FTU1SFTTVSF14* t Maximum Working Temperature: 250˚F (120˚C) tApplication:*OEPPSBOE0VUEPPS6TF Component Material #PEZ %VDUJMF*SPO &QPYZ$PBUFE %JTD %VDUJMF*SPO &1%.PS/#3&ODBQTVMBUFE 4UFN 4UBJOMFTT4UFFM 5ISPUUMJOH1MBUF 4UFFM ;JOD1MBUFE )BOEMF $BSCPO4UFFM &QPYZ$PBUJOHPS$BTUJOH Model: 8200G (Grooved) (G d) Model: 8200W (Wafer) Dimensions: *ODIFT .JMMJNFUFST (Grooved) Type 8200G Size in/mm L1 W H1 H2 2-1/2” 3” 4” 6” 8” Dimensions: *ODIFT .JMMJNFUFST (Wafer) Type 8200W Size in/mm L1 W H1 H2 2-1/2” 3” 4” 2 (52) 6” 2.2 (56) 8” 12 www.fivalcoinc.com Butterfly Valve Switch Installation Design Requirements Installation The Fivalco grooved butterfly valve should be connected to the piping system with approved couplings or flange adapters. Flow may be from either direction, and the valve may be positioned in any direction. When the valves are received from the manufacture they should be handled carefully to avoid breakage and damage to the seating area. Before installation of the valve, clean piping, flange and coupling. When the valve closes hard, it is usually due to debris lodged in the sealing area. Often this may be corrected by backing off the hand wheel and closing again. Fivalco butterfly valves have been designed with a slow close hand wheel operator which effectively minimizes water hammer. These valves feature minimum flow restriction and pressure loss when in the fully open position. Care & Maintenance Fivalco butterfly valves require no regular maintenance. However, it is advisable to inspect and verify proper operation of the unit annually or in accordance with the authorty having jurisdiction. The inspection should include a visual check for leakage at the valve pipe connection and body to operator connection. Inspection and maintenance should be performed by a qualified inspection service. The valve should never be forced to seat by applying a wrench to the hand wheel as this may distort the valve components or score the sealing surface. The use of excessive force to open or close the valve violates all warranties whether express or implied. The inlet and oulet pipe adjacent to the valve should be properly supported to prevent excessive stress on the valve body. The valve should not be used to force a pipeline into position as this may result in distortion of the valve body. Conduit and electrical connections to the optional tamper switch must be in accordance with National Electrical Code (NFPA 72) and / or requirements of the local authority having jurisdiction. Switch Installation Fivalco butterfly valves are provided with internal supervisor position switches. The tamper switch operates by cam connected to the valve stem. The switch will change position and close within two (2) full turn of the hand from the fully open position. Switch #1 Switch #2 For connection to the supervisory circuit Normally closed: 2 Red Normally open: 2 Yellow Common: 2 White Auxiliary switch connected per authority Normally closed: 1 Orange Normally open: 1 Blue Common: 1 Black Ground Lead: 1 Green Open (Yellow) S-1 Fire Alarm Control Panel Supervisory Circuit Common (White) Closed (Red) (Green) Actuator Case Ground Closed (Orange) Open (Blue) S-2 Voltage Source End of Line Resistor or Next Device Common (Black) Aux. Device (Bell or Horn) Note: 1. Rated: 5A-1/6HP-125/250V 13 www.fivalcoinc.com Model: DGC SWING CHECK VALVE | Grooved Technical Features t Connections: Grooved ends, AWWA C606 t Sizes: 2”, 2-1/2”, 3”, 4”, 6”, 8” tApprovals: UL, ULC, FM t Maximum Working Pressure: 300 PSI (Max. Test Pressure: 600 PSI) t Maximum Working Temperature: 250˚F (120˚C) tLow pressure-drop, non-slam performance Material Specification Body Ductile Iron ASTM A536 Nylon-11 Coated 2 Clapper Stainless Steel ANSI 304 3 Coil Spring Stainless Steel ANSI 302 4 Nut Stainless Steel ANSI 304 5 Bolt Stainless Steel ANSI 304 6 Washer Stainless Steel ANSI 304 7 Facing Seal Rubber EPDM 8 Seat Ring Stainless Steel ANSI 304 9 Drain Plug Ductile Iron ASTM A536 10 Pin Plug Ductile Iron ASTM A536 11 Bushing Aluminum Bronze B148 12 Hinge Pin Stainless Steel ANSI 304 13 Hook Steel ASTM A307 Component 1 Firecheck® Model: DGC Dimensions: Inches (Millimeters) Size in/mm D1 D2 D3 L L1 L2 A B 2” 1.9 (49) 2.2 (57.1) 2.4 (60.3) 6.7 (170) 0.6 (15.8) 0.3 (8.7) 1.5 (38) 4.5 (114) 2-1/2” 2.4 (62.2) 2.8 (72) 3.0 (76.1) 7.2 (184) 0.6 (15.8) 0.3 (8.7) 1.5 (38) 5.0 (127) 3” 2.9 (74) 3.3 (84.7) 3.5 (89.1) 7.7 (195) 0.6 (15.8) 0.3 (8.7) 1.4 (35) 5.6 (142) 4” 3.9 (98) 4.3 (109.8) 4.5 (114.3) 8.1 (205) 0.6 (15.8) 0.3 (8.7) 1.5 (37) 6.1 (155) 6” 6.1 (156) 6.4 (163.7) 6.6 (168.3) 12.6 (320) 0.6 (15.8) 0.3 (8.7) 1.5 (38) 8.3 (210) 8” 7.9 (201.6) 8.5 (215.8) 8.6 (218.2) 14.6 (372) 0.8 (20.1) 0.4 (10.5) 14 www.fivalcoinc.com 9.0 8.0 7.0 5.0 5.0 4.0 4.0 lve lve 12" Va 10" Va lve 8" V a 5" V al 6" V ve alv e 4" Val ve e Va lve 3" /2" 21 3.0 Va lve 6.0 2" Va lv NOMINAL PRESSURE DROP IN POUNDS PER SQUARE INCH (PSI) Friction Loss Check Valve (Water at 65˚F) 9.0 8.0 7.0 6.0 3.0 Clapper Assembly 2.0 2.0 1.5 1.5 1.0 0.9 0.8 0.7 1.0 0.9 0.8 0.7 0.6 0.6 Body 0.5 100 200 300 400 500 700 1000 2000 3000 4000 5000 7000 10000 0.5 FLOW RATE IN GALLONS PER MINUTE (GPM) Hinge Pin Plug Installation Options t Horizontal Installation: Hinge Pin must be located at the top. t Vertical Installation: Spring Direction of the arrow must point upward. Hinge Pin Drain Plug Nominal Pipe Sizes Seat Ring Flow Data - Friction Loss (Ft. of Pipe) Inches DN OD Inches (mm) C=100 Sch.10 Feet (M) C=100 Sch. 30 Feet (M) C=100 Sch.40 Feet (M) C=120 Sch.10 Feet (M) C=120 Sch. 30 Feet (M) C=120 Sch.40 Feet (M) 2” DN50 2.375 (60.3) 10 (3.0) - 8 (2.4) 14 (4.3) - 11 (3.4) 2 1/2” DN65 2.875 (73.0) 14 (4.3) - 10 (3.0) 20 (6.1) - 15 (4.6) 3” DN80 3.5 (88.9) 17 (5.2) - 12 (3.7) 23 (7.0) - 17 (5.2) 4” DN100 4.5 (114.3) 17 (5.2) - 13 (4.0) 23 (7.0) - 18 (5.5) 6” DN150 6.625 (168.3) 23 (7.0) - 19 (5.8) 33 (10.1) - 26 (7.9) 8” DN200 8.625 (219.1) 35 (10.7) 32 (9.8) 30 (9.1) 50 (15.2) 45 (13.7) 43 (13.1) 15 www.fivalcoinc.com Model: 5201-300-FLA SWING CHECK VALVE | Flanged Technical Features t Connections: Flanged (ANSI B16.1 Class 125) t Sizes: 2”, 2-1/2”, 3”, 4”, 5”, 6”, 8”, 10”, 12” tApprovals: UL, ULC, FM t Maximum Working Pressure: 300 PSI t Maximum Working Temperature: 250˚F (120˚C) tFusion bonded epoxy coated t Design Conforms to AWWA C508, Clear Waterway Component Material Seat Ring Bronze ASTM B62 Plug Washer PTFE Commercial Specification Hinge Pin Stainless Steel AISI 304 Retainer Washer Bronze ASTM B62 Ductile Iron A536 65-45-12 Ductile Iron A536 65-45-12 Gasket EPDM Commercial Cover Ductile Iron A536 65-45-12 Body Ductile Iron A536 65-45-12 Model: 5201-300-FLA øF øF H H Disc Clapper Arm L L Sizes 2" thru 4” Sizes 5" thru 12” Dimensions Size L H øF mm 50 65 inch 2 2 1/2 3 4 5 6 8 10 12 mm 203 254 279 330 356 406 495 559 660 80 100 125 150 200 250 300 inch 8 10 11 13 14 16 19.5 22 26 mm 122 133 136.5 162.5 296 298.5 357 410 463 inch 4.8 5.2 5.4 6.4 11.7 11.7 14.1 16.1 18.3 mm 152.4 178 191 229 254 279 343 406 483 inch 6 7 7.5 9 10 11 13.5 16 19 16 www.fivalcoinc.com Model: 3299-300-FLA 300 PSI OS&Y Gate Valve | Flanged Ends Technical Features t Connections: Flanged (ANSI B16.1 Class 125) t Sizes: 2-1/2”, 3”, 4”, 5”, 6”, 8”, 10”, 12” tApprovals: UL, ULC, FM t Maximum Working Pressure: 300 PSI t Maximum Working Temperature: 250˚F (120˚C) tType: Resilient Wedge, Outside Stem & Yoke tFinish: Epoxy Coated Interior and Exterior t1SF(SPPWFE4UFNGPS4VQFSWJTPSZ4XJUDI tSpecifications: %FTJHOBOE%JNFOTJPOT$POGPSNUP"88"$ Material Specification 1 Component Body Ductile Iron ASTM A536 65-45-12 2 Resilient Wedge Ductile Iron EPDM Coated ASTM A536 65-45-12 + EPDM 3 Stem Stainless Steel AISI SS304 / SS302 4 Bonnet Ductile Iron ASTM A536 65-45-12 5 Wedge Nut Stainless Steel ASTM A351 CF8 6 (MBOE Ductile Iron ASTM A536 65-45-12 7 Stem Nut Bronze ASTM B62 8 4UFN/VU8BTIFS Brass ASTM B16 9 )BOEXIFFM8BTIFS Brass ASTM B16 10 )BOEXIFFM Ductile Iron ASTM A536 65-45-12 11 )BOEXIFFM/VU Bronze ASTM B62 12 Plug Brass ASTM B16 13 Stuffing Seal EPDM ASTM D2000 EPDM 14 Stuffing PTFE ASTM D4745 15 (BTLFU EPDM ASTM D2000 EPDM 16 Tapper Pin Stainless Steel ASTM SS316 17 Hex Socket Cap Screw Steel (S 18 Nut Stainless Steel ASTM SS304 19 Square Bolt Stainless Steel ASTM SS304 20 4QSJOH8BTIFS Stainless Steel ASTM SS304 21 O Ring EPDM ASTM D2000 EPDM 22 Hex Socket Cap Screw Stainless Steel ASTM SS304 Model: 3299-300-FLA Dimensions Size 2 1/2 3 4 5 6 8 10 12 mm JODI mm JODI mm JODI mm JODI mm JODI mm JODI mm JODI mm JODI L Hmax Hmin C øD2 øD1 190 7.5 203 8 229 9 254 10 267 10.5 292 11.5 330 13 356 14 417.5 16.4 487.5 19.2 538 21.2 654 25.7 740 29.1 935 36.8 1126 44.3 1316 51.8 350.5 13.8 405.5 16 436 17.2 528 20.8 591 23.3 730 28.7 871 34.3 1011 39.8 17.5 0.7 19 0.7 23.8 0.9 23.8 0.9 25.4 1 28.6 1.1 30.2 1.2 31.8 1.3 183 7.2 253 10 253 10 305 12 305 12 355 14 445 17.5 445 17.5 178 7 191 7.5 229 9 254 10 279 11 343 13.5 406 16 483 19 17 www.fivalcoinc.com Model: 3299-300-FG Model: 3299-FG 300 PSI OS&Y Gate Valve | Flanged x Grooved Technical Features t Connections: Flanged x Grooved (ANSI B16.1 x AWWA C606) t Sizes: 2-1/2”, 3”, 4”, 5”, 6”, 8”, 10”, 12” tApprovals: UL, ULC, FM t Maximum Working Pressure: 300 PSI t Maximum Working Temperature: 250˚F (120˚C) tType: Resilient Wedge, Outside Stem & Yoke tFinish: Epoxy Coated Interior and Exterior t1SF(SPPWFE4UFNGPS4VQFSWJTPSZ4XJUDI tSpecifications: %FTJHOBOE%JNFOTJPOT$POGPSNUP"88"$ Specification Body Ductile Iron ASTM A536 65-45-12 2 Resilient Wedge Ductile Iron EPDM Coated ASTM A536 65-45-12 + EPDM 3 Stem Stainless Steel AISI SS304 / SS302 ASTM A536 65-45-12 Component 4 Bonnet Ductile Iron 5 Wedge Nut Stainless Steel ASTM A351 CF8 6 Gland Ductile Iron ASTM A536 65-45-12 7 Stem Nut Bronze ASTM B62 8 Stem Nut Washer Brass ASTM B16 9 Handwheel Washer Brass ASTM B16 10 Handwheel Ductile Iron ASTM A536 65-45-12 11 Handwheel Nut Bronze ASTM B62 12 Stuffing Seal EPDM ASTM D2000 EPDM ASTM D4745 13 Stuffing PTFE 14 Plug Brass ASTM B16 15 Gasket EPDM ASTM D2000 EPDM 16 Hex Socket Cap Screw Steel Gr 8.8 17 Tapper Pin Stainless Steel ASTM SS316 18 O Ring EPDM ASTM D2000 EPDM 19 Nut Stainless Steel ASTM SS304 20 Square Bolt Stainless Steel ASTM SS304 21 Spring Washer Stainless Steel ASTM SS304 22 Hex Socket Cap Screw Stainless Steel ASTM SS304 Model: 3299-300-FG F Material 1 Dimensions Size 2 1/2 3 4 5 6 8 10 12 mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch L H2 H1 øD4 øD3 øD2 B A ØF 190 7.5 203 8 229 9 254 10 267 10.5 292 11.5 330 13 356 14 418 16.5 478 18.8 538 21.2 654 25.7 740 29.1 935 36.8 1126 44.3 1316 51.8 351 13.8 406 16 436 17.2 528 20.8 591 23.3 730 28.7 871 34.3 1011 39.8 183 7.2 253 10 253 10 306 12 73 2.9 88.9 3.5 143 5.6 141.3 5.6 168.3 6.6 219.1 8.6 273 10.7 323.9 12.8 68.9 2.7 84.7 3.3 109.8 4.3 136.8 5.4 163.7 6.4 214.1 8.4 268 10.6 317.9 12.5 8 0.3 8 0.3 9.5 0.4 9.5 0.4 9.5 0.4 11 0.4 12.7 0.5 12.7 0.5 15.9 0.6 15.9 0.6 15.9 0.6 15.9 0.6 15.9 0.6 19 0.7 19 0.7 19 0.7 178 7 191 7.5 229 9 254 10 279 11 343 13.5 406 16 483 19 306 12 355 14 445 17.5 445 17.5 18 www.fivalcoinc.com Model: 3299-300-GG 300 PSI OS&Y Gate Valve | Grooved x Grooved Technical Features t Connections: Grooved x Grooved Ends (AWWA C606) t Sizes: 2-1/2”, 3”, 4”, 5”, 6”, 8”, 10”, 12” tApprovals: UL, ULC, FM t Maximum Working Pressure: 300 PSI t Maximum Working Temperature: 250˚F (120˚C) tType: Resilient Wedge, Outside Stem & Yoke tFinish: Epoxy Coated Interior and Exterior t1SF(SPPWFE4UFNGPS4VQFSWJTPSZ4XJUDI tSpecifications: %FTJHOBOE%JNFOTJPOT$POGPSNUP"88"$ Material Specification 1 Component Body Ductile Iron ASTM A536 65-45-12 2 Resilient Wedge Ductile Iron EPDM Coated ASTM A536 65-45-12 + EPDM 3 Stem Stainless Steel AISI SS304 / SS302 4 Bonnet Ductile Iron ASTM A536 65-45-12 5 Wedge Nut Stainless Steel ASTM A351 CF8 6 Gland Ductile Iron ASTM A536 65-45-12 7 Stem Nut Bronze ASTM B62 8 4UFN/VU8BTIFS Brass ASTM B16 9 )BOEXIFFM8BTIFS Brass ASTM B16 10 )BOEXIFFM Ductile Iron ASTM A536 65-45-12 11 )BOEXIFFM/VU Bronze ASTM B62 12 Stuffing Seal EPDM ASTM D2000 EPDM 13 Stuffing PTFE ASTM D4745 14 Plug Brass ASTM B16 15 Gasket EPDM ASTM D2000 EPDM 16 Hex Socket Cap Screw Steel Gr 8.8 17 Tapper Pin Stainless Steel ASTM SS316 18 O Ring EPDM ASTM D2000 EPDM 19 Nut Stainless Steel ASTM SS304 20 Square Bolt Stainless Steel ASTM SS304 21 4QSJOH8BTIFS Stainless Steel ASTM SS304 22 Hex Socket Cap Screw Stainless Steel ASTM SS304 Model: 3299-300-GG Dimensions Size 2 1/2 3 4 5 6 8 10 12 mm JODI mm JODI mm JODI mm JODI mm JODI mm JODI mm JODI mm JODI L H2 H1 øD4 øD3 øD2 B A 190 7.5 203 8 229 9 254 10 267 10.5 292 11.5 330 13 356 14 418 16.5 478 18.8 538 21.2 654 25.7 740 29.1 935 36.8 1126 44.3 1316 51.8 351 13.8 406 16 436 17.2 528 20.8 591 23.3 730 28.7 871 34.3 1011 39.8 183 7.2 253 10 253 10 306 12 306 12 355 14 445 17.5 445 17.5 73 2.9 88.9 3.5 143 5.6 141.3 5.6 168.3 6.6 219.1 8.6 273 10.7 323.9 12.8 68.9 2.7 84.7 3.3 109.8 4.3 136.8 5.4 163.7 6.4 214.1 8.4 268 10.6 317.9 12.5 8 0.3 8 0.3 9.5 0.4 9.5 0.4 9.5 0.4 11 0.4 12.7 0.5 12.7 0.5 15.9 0.6 15.9 0.6 15.9 0.6 15.9 0.6 15.9 0.6 19 0.7 19 0.7 19 0.7 19 www.fivalcoinc.com Model: 3288-300-FLA 300 PSI NRS Gate Valve | Flanged Ends Technical Features t Connections: Flanged (ANSI B16.1 Class 125) t Sizes: 2-1/2”, 3”, 4”, 5”, 6”, 8”, 10”, 12” tApprovals: UL, ULC, FM t Maximum Working Pressure: 300 PSI t Maximum Working Temperature: 250˚F (120˚C) tType: Resilient Wedge, Non-Rising Stem tFinish: Epoxy Coated Interior and Exterior t*OEJDBUPS1PTU1BUUFSO tSpecifications: Design and Dimensions Conform to AWWA C515 Material Specification 1 Body Ductile Iron ASTM A536 65-45-12 2 Resilient Wedge Ductile Iron EPDM Coated ASTM A536 65-45-12 + EPDM 3 Stem Stainless Steel AISI SS304 / SS302 4 Bonnet Ductile Iron ASTM A536 65-45-12 5 Thrust Collar Copper ASTM C51100 6 Gland Ductile Iron ASTM A536 65-45-12 7 Wedge Nut Bronze ASTM B62 8 O Ring EPDM ASTM D2000 EPDM Component 9 Dustproof Cover EPDM ASTM D2000 EPDM 10 Post Flange Ductile Iron ASTM A536 65-45-12 11 Wrench Nut Ductile Iron ASTM A536 65-45-12 12 O Ring EPDM ASTM D2000 EPDM 13 Plug Brass ASTM B16 14 O Ring EPDM ASTM D2000 EPDM ASTM SS316 Washer Stainless Steel 16 Hex Socket Cap Screw Stainless Steel ASTM SS316 17 Gasket EPDM ASTM D2000 EPDM 18 Hex Socket Cap Screw Steel Gr 8.8 19 Nut Stainless Steel ASTM SS316 20 Studs Stainless Steel ASTM SS316 21 Spring Washer Stainless Steel ASTM SS316 22 Washer Stainless Steel ASTM SS316 12” F 15 Model: 3288-300-FLA Dimensions Size 2 1/2 3 4 5 6 8 10 12 mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch L H C øF 190 7.5 203 8 229 9 254 10 267 10.5 292 11.5 330 13 356 14 203.5 8 232 9.1 251 9.9 320 12.6 351.5 13.8 435 17.1 535 21.1 616 24.3 17.5 0.7 19 0.7 23.8 0.9 23.8 0.9 25.4 1 28.6 1.1 30.2 1.2 31.8 1.3 178 7 191 7.5 229 9 254 10 279 11 343 13.5 406 16 483 19 20 www.fivalcoinc.com Model: 3288-300-FG 300 PSI NRS Gate Valve | Flanged x Grooved Technical Features t Connections: Flanged x Grooved Ends (ANSI B16.1 x AWWA C606) t Sizes: 2-1/2”, 3”, 4”, 5”, 6”, 8”, 10”, 12” tApprovals: UL, ULC, FM t Maximum Working Pressure: 300 PSI t Maximum Working Temperature: 250˚F (120˚C) tType: Resilient Wedge, Non-Rising Stem tFinish: Epoxy Coated Interior and Exterior t*OEJDBUPS1PTU1BUUFSO tSpecifications: Design and Dimensions Conform to AWWA C515 Material Specification 1 Component Body Ductile Iron ASTM A536 65-45-12 2 Resilient Wedge Ductile Iron EPDM Coated ASTM A536 65-45-12 + EPDM 3 Stem Stainless Steel AISI SS304 / SS302 4 Bonnet Ductile Iron ASTM A536 65-45-12 5 Thrust Collar Copper ASTM C51100 6 Gland Ductile Iron ASTM A536 65-45-12 7 Wedge Nut Bronze ASTM B62 8 O Ring EPDM ASTM D2000 EPDM Model: 3288-300-FG 12” 9 Dustproof Cover EPDM ASTM D2000 EPDM 10 Post Flange Ductile Iron ASTM A536 65-45-12 11 Wrench Nut Ductile Iron ASTM A536 65-45-12 12 O Ring EPDM ASTM D2000 EPDM 13 Plug Brass ASTM B16 14 O Ring EPDM ASTM D2000 EPDM ASTM SS316 Washer Stainless Steel 16 Hex Socket Cap Screw Stainless Steel ASTM SS316 17 Gasket EPDM ASTM D2000 EPDM 18 Hex Socket Cap Screw Steel Gr 8.8 19 Nut Stainless Steel ASTM SS316 20 Studs Stainless Steel ASTM SS316 21 Spring Washer Stainless Steel ASTM SS316 22 Washer Stainless Steel ASTM SS316 ØF 15 Dimensions Size 2 1/2 3 4 5 6 8 10 12 mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch L H ØD3 ØD2 B A ØF 190 7.5 203 8 229 9 254 10 267 10.5 292 11.5 330 13 356 14 295 11.6 323 12.7 342 13.5 408 16.1 440 17.3 537 21.1 640 25.2 723 28.5 73 2.9 88.9 3.5 143 5.6 141.3 5.6 168.3 6.6 219.1 8.6 273 10.7 323.9 12.8 68.9 2.7 84.7 3.3 109.8 4.3 136.8 5.4 163.7 6.4 214.1 8.4 268 10.6 317.9 12.5 8 0.3 8 0.3 9.5 0.4 9.5 0.4 9.5 0.4 11 0.4 12.7 0.5 12.7 0.5 15.9 0.6 15.9 0.6 15.9 0.6 15.9 0.6 15.9 0.6 19 0.7 19 0.7 19 0.7 178 7 191 7.5 229 9 254 10 279 11 343 13.5 406 16 483 19 21 www.fivalcoinc.com Model: 3288-300-GG 300 PSI Gate Valve | Grooved x Grooved Technical Features t Connections: Grooved x Grooved Ends (AWWA C606) t Sizes: 2-1/2”, 3”, 4”, 5”, 6”, 8”, 10”, 12” tApprovals: UL, ULC, FM t Maximum Working Pressure: 300 PSI t Maximum Working Temperature: 250˚F (120˚C) tType: Resilient Wedge, Non-Rising Stem tFinish: Epoxy Coated Interior and Exterior t*OEJDBUPS1PTU1BUUFSO tSpecifications: Design and Dimensions Conform to AWWA C515 Material Specification 1 Body Ductile Iron ASTM A536 65-45-12 2 Resilient Wedge Ductile Iron EPDM Coated ASTM A536 65-45-12 + EPDM 3 Stem Stainless Steel AISI SS304 / SS302 4 Bonnet Ductile Iron ASTM A536 65-45-12 5 Thrust Collar Copper 6 Gland Ductile Iron 7 Wedge Nut Bronze ASTM B62 8 O Ring EPDM ASTM D2000 EPDM Component Model: 3288-300-GG ASTM C51100 ASTM A536 65-45-12 12” 9 Dustproof Cover EPDM ASTM D2000 EPDM 10 Post Flange Ductile Iron ASTM A536 65-45-12 11 Wrench Nut Ductile Iron ASTM A536 65-45-12 12 O Ring EPDM ASTM D2000 EPDM 13 Plug Brass ASTM B16 14 O Ring EPDM ASTM D2000 EPDM ASTM SS316 15 Washer Stainless Steel 16 Hex Socket Cap Screw Stainless Steel ASTM SS316 17 Gasket EPDM ASTM D2000 EPDM 18 Hex Socket Cap Screw Steel Gr 8.8 19 Nut Stainless Steel ASTM SS316 20 Studs Stainless Steel ASTM SS316 21 Spring Washer Stainless Steel ASTM SS316 22 Washer Stainless Steel ASTM SS316 Dimensions Size 2 1/2 3 4 5 6 8 10 12 mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch L H ØD3 ØD2 B A 190 7.5 203 8 229 9 254 10 267 10.5 292 11.5 330 13 356 14 295 11.6 323 12.7 342 13.5 408 16.1 440 17.3 537 21.1 640 25.2 723 28.5 73 2.9 88.9 3.5 143 5.6 141.3 5.6 168.3 6.6 219.1 8.6 273 10.7 323.9 12.8 68.9 2.7 84.7 3.3 109.8 4.3 136.8 5.4 163.7 6.4 214.1 8.4 268 10.6 317.9 12.5 8 0.3 8 0.3 9.5 0.4 9.5 0.4 9.5 0.4 11 0.4 12.7 0.5 12.7 0.5 15.9 0.6 15.9 0.6 15.9 0.6 15.9 0.6 15.9 0.6 19 0.7 19 0.7 19 0.7 22 www.fivalcoinc.com Model: IP0888 INDICATOR POST | Adjustable Vertical Type Technical Features t7FSUJDBM5ZQF "EKVTUBCMF t6- 6-$-JTUFE '."QQSPWFE No. QTY. Component Material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odel: IP0888 Field Adjustment 3FNPWFUIFUPQTFDUJPOGSPNUIFUPQPGUIF*OEJDBUPS1PTUBTTFNCMZ $VUUIFSFRVJSFEMFOHUIPòUIFCPUUPNPGUIF4UBOEQJQFGPSUIF(SPVOE-JOF UPNBUDIVQXJUI4UBOEQJQF(SPVOE-JOFNBSL 4FUUIFi0QFOwBOEw4IVUwUBSHFUTGPSUIFBQQSPQSJBUFWBMWFTJ[F 3FBUUBDIUIFUPQTFDUJPOUPUIFUPQPGUIF*OEJDBUPS1PTUBTTFNCMZ %FTJHOBOEEJNFOTJPOTBSFTVCKFDUUPDIBOHFXJUIPVUOPUJDF 23 www.fivalcoinc.com Model: IP0888 Installation | Adjustable Vertical Type Installation 6) Final Assembly and Test Note: Ensure that the Non-rising Stem Gate Valve is in the fully Insert the Target Carrier Assembly back into the Top Section by open position before installing the Vertical Indicator Post. rotating the Operating Nut (2) clockwise, Rotate untill the Open 1) Disassemble the Indicator Post Target is centered in the window of the window of the Body which corresponds with the Nutrising Stem Gate Valve being in Take off the Locking Wrench (1). Slide off the Top Section the open position. Lower the Top section with Target Carrier together with the Operating Nut (12) and the Square Stem (22) Assembly onto the Body, assuring that the Stem Engages with as well as the Crane Coupling (19) and ensure that all other the Operating Nut at least 2 inches but not more than 4.5 accessories attached from the end of the Body by loosening two inches. Secure the Top Section to the Body by tightening the Hex Cap screws and Square Nut. Slide off the Body (13) from the Cap Screw and Square Nut Close the Non-rising Stem Gate Valve Stand pipe (21) by loosening two Hex Cap Screws and Hex Nut, and make sure that the Shut Target (not shown) is properly Loosen the two Hex Cap Screws and Hex Nut. Slide off the centered in the window of the Body and adjust as necessary. Standpipe (21) from the Base Flange (16). Maintenance 2) Install the Base Flange and Standpipe Oil the bearing in the Top Section at least once per year by Attach the base flange (16) together with the Standpipe (21) to adding several drops of oil in the hole located on the top of the the Post Flange of the Non-rising Stem Gate Valve using the four Operating Nut. Cap Screws and Hex Nut. 3) Adjust the Grade Line Mark Pull in and lower the Body (13) over the Standpipe (21) untill the OPEN SHUT Ground Line Mark on the Body is the same height as ground Table 1 level. Tighten the Two Hex Cap Screws and Hex Nut. Valve Size 4) Adjust Square Stem Min. Bury Depth Max. Bury Depth 4” 31.14” 65.39” 6” 35.12” 69.37” 8” 38.58” 72.83” 10” 42.32” 76.57” 12” 42.51” 79.76” Valve Size H (in) H (mm) 4” 9.88” 251 the Target Carrier Assembly by pulling the middle section of the 6” 13.86” 352 Target (Open and Shut) a small distance away from the Target 8” 17.32” 440 10” 21.06” 535 12” 24.25” 616 Lower the Stem (22) into Body standpipe (21) such that the Crane Coupling (19) fits over the Operating nut of Non-rising Stem Gate Valve. Ensure thaat the Stem (22) engages the Operating Nut (2) a minimum of 2 inches but no more than 4,5 inches, to check for correct engagement, the end of the stem should be from 2 - 4. 5 inches below the top of the Body. 5) Adjust the Targets Remove the Target Carrier Assembly from inside the Body by Table 2 rotating the Operating Nut (19) counterclockwise. The Open Target and Shut Target (not shown) are adjusted up or down on 24 www.fivalcoinc.com Model: WP0999 INDICATOR POST | Wall Type Technical Features t8BMM5ZQF t6- 6-$-JTUFE '."QQSPWFE No. QTY. Component Material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odel: WP0999 Field Adjustment 3FNPWFUIFUPQTFDUJPOGSPNUIFUPQPGUIFJOEJDBUPS1PTUBTTFNCMZ 4FUUIFi0QFOwBOEw4IVUwUBSHFUTGPSUIFBQQSPQSJBUFWBMWFTJ[F 3FBUUBDIUIFUPQTFDUJPOUPUIFUPQPGUIFJOEJDBUPSQPTUBTTFNCMZ %FTJHOBOEEJNFOTJPOTBSFTVCKFDUUPDIBOHFXJUIPVUOPUJDF 25 www.fivalcoinc.com Model: FXB, FXU Flexible Sprinkler Connector | Braided & Unbraided Technical Features t Hose Types: Braided or Unbraided t Hose Lengths: 24”, 36”, 48”, 60”, 72” t Maximum Working Pressure: 175 PSI t Maximum Working Temp: 225˚F tK factor: ½” Outlet 5.6, ¾” Outlet 8.0 tConnections: To branch line (inlet) via 1”/25.4mm NPT male thread tConnections: To sprinkler head (outlet) via ½” or ¾” 15mm or 20mm NPT female thread Approvals & Standards t Braided: UL, ULC 2443, FM 1637 tUnbraided: UL, ULC 2443 t/'1" /'1"% /'1"3 "45.$ "45.$ Part Material Flexible Hose Type 304 Stainless Steel Nut S10C *TPMBUJPO3JOH Nylon 66 Gasket Seal Silicon 3FEVDFS Zinc Plated Grade 1020 Steel End & Center Brackets ;JOD1MBUFE4UFFM"45." Square Bar Zinc Plated Steel Grade 1010 Steel Quickonnect® Model: FXB (Braided), FXU (Unbraided) 26 www.fivalcoinc.com Model: Firelet Welded Pipe Outlets | Threaded Technical Features t$POGPSNUP"45." (SBEFT"PS# 5ZQF& t5ISFBETBSFDVUJOBDDPSEBODFUP"/4*#PS*40UISFBET t8JEFWBSJFUZPGIFBEFSTJ[FT t Maximum Working Pressure: 14* t Maximum Test Pressure: 14* t Maximum Working Temp: 250ºF tMaterials: &RVJWBMFOUUP"45." Firelet® Model: Firelet Chemical Properties Ca 0.035% max. Ma 0.6 ~ 1.05% P 0.04% max. Su 0.05% max. Si 0.035% max. Dimensions: Inches (Millimeters) Size in/mm A C D M 1/2” 0.040 (1.036) 0.039 (1.000) 0.032 (0.812) 0.012 (0.300) 3/4” 0.049 (1.252) 0.039 (1.000) 0.039 (1.000) 0.020 (0.500) 1” 0.059 (1.508) 0.043 (1.100) 0.051 (1.299) 0.020 (0.500) 1 1/4” 0.073 (1.863) 0.049 (1.250) 0.064 (1.614) 0.020 (0.500) 1 1/2” 0.082 (2.100) 0.049 (1.250) 0.073 (1.850) 0.034 (0.875) 2” 0.102 (2.583) 0.059 (1.500) 0.091 (2.307) 0.034 (0.875) 2 1/2” 0.126 (3.200) 0.069 (1.755) 0.108 (2.758) 0.044 (1.125) Run / Pipe Outlet Pipe (A) Run Pipe (B) Outlet Pipe (A) 1 ~ 1 1/2” 1/2” 2 ~ 2 1/2” 3 ~ 8” 3/4” Outlet Pipe (A) 1 1/4” Run Pipe (B) 2” 2 ~ 2 1/2” 2 ~ 2 1/2” 3” 4 ~ 5” 2” 3” 4” 1~ 1 1/2” 6 ~ 8” 2 ~ 2 1/2” 2 ~ 2 1/2” 6 ~ 8” 3 ~ 5” 3” 2 1/2” 6 ~ 8” 1” Run Pipe (B) 1 1/2” 3” 4” 1 1/4” ~ 1 1/2” 5 ~ 6” 2 ~ 2 1/2” 8” 2 1/2” 4” 6” 3” 8” 4 ~ 5” 6 ~ 8” 27 www.fivalcoinc.com Installation, Operation and Maintanance | Resilient Seated Gate Valves 1. General 5. Installation Resilient seated gate valves form a significant component of many firefighting and water distribution systems. Failure of a resilient seated gate valve in such systems, either due to faulty installation or improper maintenance, could result in extensive damage and costly repairs. In addition, many resilient seated gate valves are installed in buried service or underground applications. Problems with or malfunctions of the valves due to faulty installation or improper maintenance may result in extensive and costly unearthing operation to effectively correct or eliminate the problem. Many resilient seated gate valve problems and failures can be traced back to improper installation, operation, or maintenance procedures. At the jobsite prior to installation, each valve should be visually inspected and any foreign material in the interior portion of the valve should be removed. A detail inspection of the valve as outlined in Sec. 3 should be performed prior to installation. 2. Unloading All valves should be unloaded carefully. Each valve should be carefully lowered from the truck to the ground; it should not be dropped. In the case of larger valves, forklifts or slings around the body of the valve or under the skids should be used for unloading. Only hoists and slings with adequate load capacity to handle the weight of the valves should be used. Hoists should not be hooked into or chains fastened around yokes, gearing, motors, cylinders or handwheels. Failure to carefully follow these recommendations is likely to result in damage to the valve. 3. Inspection Prior To Installation Resilient seated gate valves should be inspected at the time of receipt for damage in shipment. The initial inspection should be to verify compliance with specifications, direction of opening, size and shape of operating nut, number of turns to open or close, and type of end connections. A visual inspection of the seating surfaces should be performed to detect any damage in shipment or scoring of the seating surfaces. Inspection personnel should look for bent stems, broken handwheels, cracked parts, loose bolts, missing parts and accessories, and any other evidence of mishandling during shipment. Each valve should be operated through one complete opening and closing cycle in the position which it is to installed. 4. Storage Valves should be stored in the fully closed position to prevent the entry of foreign material that could cause damage to the seating surface. Whenever practical, valves should be stored indoors. If outside storage is required, means should be provided to protect the operating mechanism from weather elements. During outside storage, valves should be protected from the weather, sunlight, ozone, and foreign materials. In colder climates where valves may be subject to freezing temperatures, it is absoutely essential to remove the water from the valve interior and close the valve before storage. Failure to do so may result in a cracked valve casting and or deterioration of the resilient seat material. 5.1 Bolts All bolts should be checked for proper tightness and protected by the installer to prevent corrosion, either with a suitable paint or by polyethylene wrapping. 5.2 Undergound Installation Valves in water distribution lines shall, where practical, be located in easily accessible areas. 5.2.1 During installation there is the possibility of foreign materials inadvertently entering the valve. Foreign material can damage internal working parts during operation of gate valve. For this reason, gate valves should be installed in the closed position. Each valve should be placed on firm footing in the trench to prevent settling and excessive strain on the connection to the pipe. Pipe systems should be supported and aligned to avoid damage to the valve. 5.2.2 A valve box or vault should be provided for each valve used in a buried service application. The valve box should be installed so as not to transmit shock loads or stress to the valve. The valve box should be centered over operating nut of the valve with the box cover flush with the surface of the finished area or such other level as directed by the owner. Valve boxes should be of such design that a traffic load on the top of is not transmitted to the valve. 5.2.3 Valves buried in unusually deep trenches should have special provisions for operating the valve-either a riser on the stem to permit use of a normal key or a notation on the valve records that a long key will be required. 5.2.4 When valves with exposed gearing or operating mechanisms are installed belowground, a vault designed to allow pipe clearance and prevent settling on the pipe should be provided. The operating nut should be accessible from the top opening of the vault with a valve key. The size of the vault should provide for easy remove of the valve bonnet and internal parts of the valve for purpose of repair. Consideration should be given to the possible entry of groundwater and/or surface water and to the need to provide for the disposal of such water. 5.3 Aboveground Installation Valve installed aboveground or in a plant piping system should be supported and aligned to avoid damage to the valves. Valve should not be used to correct the misalignment of piping. 28 www.fivalcoinc.com Installation, Operation and Maintanance | Resilient Seated Gate Valves 5.2.4 When valves with exposed gearing or operating mechanisms are installed belowground, a vault designed to allow pipe clearance and prevent settling on the pipe should be provided. The operating nut should be accessible from the top opening of the vault with with a valve key. The size of the vault should provide for easy remove of the valve bonnet and internal parts of the valve for purpose of repair. Consideration should be given to the possible entry of groundwater and/or surface water and to the need to provide for the disposal of such water. 5.3 Aboveground Installation Valve installed aboveground or in a plant piping system should be supported and aligned to avoid damage to the valves. Valve should not be used to correct the misalignment of piping. 5.4 Inspection After Installation and before pressurization of the valve, all pressure containing bolting (bonnet, seal plate, packing gland, and end connections) should be inspected for adequate tightness to prevent leakage. In addition, an inspection should be made for adequate tightness of all tapped and plugged connections to the valve interior. Proper inspection at this time will minimize the possibility of leaks after pressurization of the piping system. 5.5 Testing In order to prevent time lost seaching for leaks, it is recommended that the valve excavations are not backfilled until after pressure tests have been made. After installation, it is desirable to test newly installed piping sections, including valves, at some pressure above the system design pressure. The test pressure should not exceed the rated working pressure of the valve. After the test, steps should be taken to relieve any tapped pressure in the body of the valve. The resilient-seated gate valve should not be operated in either the opening or closing direction at different pressures above the rated working pressure. It is also recognized that wear or foreign material may damage valve seating surfaces and may cause leakage. 5.6 Records On completion of the installation, valve location, size, make type, date of installation, number of turns to open, direction of opening, and other information deemed pertinent should be entered on permanent records. 5.7 Application Hazards Resilient seated gate valves should not be installed in applications or for service other than those recommended by the manufacturer. 5.7.1 Resilient seated gate valves should not be installed in lines where service pressure will exceed that rated working pressure of the valve. 5.7.2 Resilient seated gate valves should not be used for throttling service unless the design is specifically recommended for that purpose or approved in advance by the manufacture. 5.7.3 Resilient seated gate valves should not be used in applications that are exposed to freezing temperature unless sufficient flow is maintained through the valve or other protection is provided to prevent freezing. 5.7.4 Gate valves should not be installed at a dead end or near a bend in a pipline without proper and adequate restraint to support the valve and prevent it from blowing off the end of the line. 5.7.5 To prevent damage, 4” and below size NRS resilient seated gate valves should not be operated with input torques greater than 200 ft-lb (270N.m) Gate valves 6” to 12” NRS should not be operated with input torques greater than 300ft-lb (406N.m). 6. Inspection and Maintenance Each valve should be operated through a full cycle and returned to its normal position on a time schedule designed to prevent a buildup of tuberculation or other deposits thay could render the valve inoperable or prevent a tight shut off. The interval of time between operations in critical locations, or valves subjected to severe operating conditions, should be shorter than that for less important installations, but can be whatever time period is found to be satisfactory based on local experience. The number of turns required to complete the operation cycle should be recorded and compared with permanent installation records to ensure full gate travel. When using portable auxiliary power actuators with input torque capacities exceeding the maximum operating torques recommended in Sec. 5.7.5, extreme care should be taken to avoid the application of excessive torque to the valve stem. If the actuator has a torque-limiting device, it should be set below the valves in Section 5.7.5. If there is no torque limiting device, the recomended practice is to stop the power actuator three or four turns before the valve is fully opened or fully closed and then complete the operation manually. Maintenance should be performed at the time a malfunction is discovered to avoid a return trip to the same valve and to prevent forgetting about it altogether. Recording system should be adopted that provides a written record of valve location, condition, maintenance, and each subsequent inspection of valve. 29 www.fivalcoinc.com Installation, Operation and Maintanance | Resilient Seated Gate Valves 6.1 Inspection Each valve should be operated through one complete operating cycle. If the stem action is tight as a result of “hard-water” buildup on the stem threads, the operation should be repeated several times until the opening and closing actions are smooth and free. With the gate in the partially open position, a visual inspection should be performed, where practical, to check for leakage at all joints, connections, and areas off packing or seals. If leakage is observed, all defective O-rings, seals, gaskets, or placed. If leakage end-connection sealing members should be replaced. he leakage should cannot be corrected immediately, the nature of the e for repairs. If the be report promptly to those who are responsible valve is inoperable of irreparable, its location should be clearly te position should established to save time for repair crews. The gate s. In addition, fire be reported to personnel responsible for repairs. partments should departments and other appropriate municipal departments be informed that the valve is out of service. ningful inspection 6.2 Record Keeping In order to carry out a meaningful he location, make, and maintenance programs, it is essential that the alve be recorded. type, size, and date of installation of each valve stem used, other Depending on the type of record keeping system information may be entered in the permanentt record. When a resilient seated gate valve is inspected, an entry should be made in pection and condithe permanent record indicating the date of inspection ould be indicated. tion of the valve. If repair work is necessary, it should On completion of the work, the nature of the repairs and date completed should be recorded. 7. Repairs Leakage, broken parts, hard operation, and other her major defects should be corrected by are pair crew as soon as possible after the ormed in the field, defect has been reported. If repairs are to be performed the repair crews should take a full complement off spare parts to the he defective valve jobsite. Provisions should be made to isolate the d pressure prior to from water pressure and relieve internal trapped mbly of the valve performing any corrective maintenance. Disassembly h the procedure should be accomplished in accordance with supplied by the manufacturer. After repairing the valve, the operatomplete operating ing mechanism should be cycled through one complete alve in the open cycle. With full line pressure applied to the valve ect leakage in the position, and inspection should be made to detect nd, and body-end areas around the seal plate, bonnet, packing gland, connections. A record should be made to indicate that the valve has arkings indicating been repaired and is in working condition. Any markings d. In addition, fire that the valve is inoperable should be removed. partments should departments and other appropriate municipal departments e. be informed of the satisfactory repair of the valve. 30 www.fivalcoinc.com Terms and Conditions Controlling Provisions: Product Specs: These terms and conditions shall control with respect to any and All weights are approximate and subject to change without all purchase orders or sales of Fivalco products. No alteration, notice. Fivalco reserves the right to change or modify product modification or waiver of these terms and conditions whether on designs, specifications and/or standard equipment without the customer’s purchase order or otherwise shall be valid unless notice and without incurring obligation. Prices and Terms and the alteration, modification, or waiver is specially accepted in Conditions of Sale are subject to change without notice. writing by an authorized representative of Fivalco, Inc. Warranty: Shipping Terms: We warrant all Fivalco products to be free from defects in materi- All orders are quoted F.O.B. shipping point unless otherwise als and workmanship under normal conditions of use and service. agreed upon in writing. Our obligation under this warranty is limited to repairing or replacing at our option at our factory or designated facility any Orders accepted are subject to approval by our Head Office and product within 2 years after delivery to the original buyer, which Credit Department and are contingent upon acts of God, war, shall be returned with transportation charges prepaid, and which civil unrest or disturbance, strikes, labor difficulties, governmen- our examination and inspection shall show to our satisfaction to tal regulations or rulings, delays of carriers (land, air, or ocean), have been defective. inability to obtain materials, accidents or any other cause beyond our control. This warranty is made expressly in lieu of any other warranties, expressed or implied, including any implied warranty of Shipping dates are estimated, and we will make effort to ship merchantability or fitness for a particular purpose. The buyer’s within the time estimated. We cannot guarantee shipping dates, sole and exclusive remedy shall be for the replacement or repair and in the event of a production or shipment delay, we reserve of defective products as provided herein. The buyer agrees that the right to change the estimated shipping date. Under no no other remedy, including but not limited to, incidental or circumstances shall Fivalco be liable for damages of any kind, consequential damages for lost profits, lost sales, injury to person including but not limited to incidental or consequential damages or property or any other incidental or consequential loss shall be for lost sales or profits or liquidated damages, directly or available to him/her. indirectly arising from delays or failure to meet shipping dates. Fivalco neither assumes nor authorizes any person to assume any Orders accepted cannot be changed or cancelled without our other liability in connection with the sale of such products. Item written consent. purchased by Fivalco and resold will have the original equipment manufacturers warranty extended to Fivalco customers where Orders for special (non-standard) goods may not be cancelled, applicable. nor will we accept return of these goods for credit. This warranty shall not apply to any product which has been the Claims for Shortages: subject to misuse, negligence or accident, which has been All claims for shortages must be made within 10 days of receipt repaired or altered in any manner outside of Fivalco’s factory or of goods. Our responsibility ceases when the goods are designated facility or which has been used in a manner contrary delivered to the carrier in good condition. Carriers are respon- to Fivalco’s instructions, recommendations or generally accepted sible for goods lost, damaged or delayed in transit. For your own practices. Fivalco shall not be responsible for design errors due to protection have the transportation company’s agent verify any inaccurate or incomplete information supplied by the buyer or damage, shortage or delay and note them on the freight bill his representatives. over his/her signature. 31 www.fivalcoinc.com Notes 32 www.fivalcoinc.com