Peerless Pump AE: Horizontal Split Case Pump Specs

Peerless Pump Company
Indianapolis, IN 46207-7026
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE DOUBLE SUCTION
Type AE
SECTION 1220
Page 1
June 1, 2004
Typical Specifications
1. General: The pump(s) shall be of the single stage, double
suction, horizontal split case design; split on the
horizontal axis and shall be bronze fitted construction.
Suction and discharge connections shall be located on
opposite sides of the lower casing, allowing removal of
the rotating element without disturbing the system piping
connections. The pump(s) shall be a Peerless Pump
Company AE design.
The pump(s) are to be designed for a capacity of
GPM at a total head of
feet,
at an efficiency of
% of design condition.
2. Casing: The pump casing material shall be a minimum of
class 35 cast iron. Water passageways shall be smooth
to permit maximum efficiency. Casing shall be
hydrostatically tested at 150% of the maximum working
pressure under which the pump could operate at design
speed. The suction flange shall be drilled (125 lb.)
(250 lb.) ANSI. The discharge flange shall be drilled (125
lb.) (250 lb.) ANSI
The bearing brackets shall be cast as an integral part of
the lower casing and have removable bracket caps. The
bearing housing shall be doweled for location and antirotation. The pump feet shall also be cast as an Integral
part of the lower casing.
Bronze renewable casing rings shall be furnished,
doweled and shouldered In the casing. Ring dowels shall
be located In slots on the split surface of the lower
casing.
3. Impeller: The impeller shall be of one piece cast bronze,
double suction type. The impeller shall be balanced,
keyed to the shaft and fixed in an axial position by
threaded shaft sleeves. The Impeller skirt shall be
grooved and fit with close tolerances to the casing ring to
permit a minimum of recirculation between the impeller
and the casing ring for maximum efficiency. (Optional:
Renewable bronze impeller rings shall be shrunk on the
impeller and locked in place with stainless steel set
screws. The impeller rings shall be grooved and fit with
close tolerances to the casing ring for maximum
efficiency.)
4. Stuffing Boxes:
Packing - The stuffing boxes shall hold a minimum of
five rings of TFE packing. The bronze gland shall be split
in two halves, to facilitate removal for repacking. Gland
bolts shall be of the swing type made of steel with 18-8
stainless steel nuts.
Mechanical Seal - Sealing of the pump liquid cavity shall
be with a face type mechanical seal with Ni-resist
stationary seat, carbon sealing washer, Buna rubber
flexible members, stainless steel metal parts and spring.
Seal to be rated for 225o F .(107o C.) @ 150 psig
(10-34 bar) maximum. Mechanical seals shall be
mounted over bronze shaft sleeves.
5. Shaft and Shaft Sleeves: The shaft shall be carbon
steel, adequately sized for the loads transmitted. Shaft
deflection shall not exceed .002 Inches at the face of the
stuffing box when operating between 95% and 105% of
capacity at best efficiency at the pump's maximum 60
Hz. speed and with full diameter Impeller. The shaft shall
be protected through the stuffing box by means of bronze
shaft sleeves and they shall be threaded against shaft
rotationand locked in place with set screws. The sleeves
shall be sealed with "O" rings at the Inside diameter to
eliminate leakage between the shaft and sleeve.
(Optional: Shaft shall be positively sealed against
pumped fluid by means of specially machined shaft
sleeves and Impeller with sockets for use with "O" ring
seals against Impeller hubs.) Shaft sleeves shall extend
beyond the packing glands (or mechanical seal flanges).
6. Bearings: Bearings shall be single row, deep groove ball
type; the inboard bearing shall be arranged for radial
loads only. The outboard bearing shall be arranged for
both radial and axial loads. Both bearings shall be
grease lubricated with grease flush through the bearing
housing (Optional: oil lube). Bearings shall be designed
for an average life of 100,000 hours.
Bearings shall be protected from liquid entry by means of
rubber deflectors mounted on the shaft and lip seals In
the bearing housings.
Outboard bearing cover shall have a plugged opening for
tachometer connection. Bearing housing lubrication
design must be capable of being changed from grease to
oil lubrication type without replacement of bearing
housing or the lower pump casing. The outboard bearing
shall have retaining ring retention.
7. Base: The pump and driver shall be mounted on a
common steel base (with optional drip rim). Pump and
driver shall be aligned and bolted In place prior to factory
shipment. Final alignment must be performed at the
jobsite In accordance with the standards of the Hydraulic
Institute and the pump Installation, operation and
maintenance instructions. Base Is to be grouted to
eliminate vibration.
8. Coupling: A flexible coupling shall be provided between
the pump and driver. A coupling guard shall be furnished
over the coupling for protection.
Subject to change without notice
SECTION 1220
Page 2
June 1, 2004
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE DOUBLE SUCTION
Type AE
Peerless Pump Company
Indianapolis, IN 46207-7026
WORKING PRESSURE AND TEMPERATURE LIMITATIONS
The maximum working pressure of a pump varies with the temperature of the pumped fluid. Tables A and B and
Curve 4852154 on page 2.1 Section 1220, present the maximum working pressure and maximum suction pressure
limits for AE model pumps based on available flange drilling, casing material and fluid temperature.
IMPORTANT NOTE
The correct packing type, sleeve material or mechanical seal must be selected in accordance with their application
rules. The standard mechanical seals for AE pumps are limited to 150 psig (10.34 bar) maximum suction pressure
and temperature up to 225o F. (107o C.).
To verify that a given model AE pump is suitable for an application, the following steps must be taken.
STEP 1:
Calculate the pump's maximum discharge pressure (MDP).
For constant RPM applications:
MDP = [Total Head at Shutoff (for the impeller diameter and RPM required for rated total head) ÷ 2.31 x
fluid’s specific gravity] + suction pressure (psi) at zero flow.
STEP 2:
Locate the pump model in Table A and note the legend letter for the applicable pressure-temperature curve for
maximum working pressure allowed.
STEP 3:
Locate the pump model in Table B and note the legend letters for the applicable pressure-temperature curve for
maximum suction pressure allowed.
STEP 4:
Enter Curve 4852154 at the fluid temperature (o F.), read vertically to the curve line noted for the pump suction
and read the maximum permissible suction pressure.
Repeat this procedure for the discharge side to determine the maximum allowable working pressure.
STEP 5:
Relate the maximum suction pressure to the pump's permissible suction pressure and choose the suction flange
rating required. Repeat for the discharge flange.
EXAMPLE:
Model 4AE11, constant RPM, fluid temperature 70 o F., suction pressure at 0 GPM = 85 psig, 1.0 specific gravity,
shutoff total head = 231 feet.
MDP = (231 ÷ 2.31 x 1.0) + 85 = 185 psi
4AE11 Discharge flange curve lines are E-E or D-D (from Table A)
4AE11 Suction flange curve lines are E-E or D-D (from Table B)
Maximum suction and discharge pressure for E-E = 175 psi, and D-D = 250 psi @ 70 o F
Therefore: 125 lb. ANSI drilling for suction flange and 250 lb. ANSI drilling for discharge flange is required for cast
iron casing.
Subject to change without notice.
Peerless Pump Company
Indianapolis, IN 46207-7026
SECTION 1220
Page 2.1
June 1, 2004
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE DOUBLE SUCTION
Type AE
WORKING AND TEMPERATURE LIMITATIONS - Continued
TABLE A
(Maximum Working Pressure)
Pump Size &
Type
2AE11
3AE9
3AE14, G
4AE10, G
4AE11, G
4AE12
5AE8, N
5AE11, G
5AE12
5AE14, G, N
6AE11
6AE12
6AE14, G, N
6AE16G, N, V
6AE18
8AE12
8AE13
8AE15, G
8AE17A, Q, W
8AE20, G
10AE12
10AE14A, J
10AE16
10AE20
DISCHARGE FLANGE
Cast Iron
Cast Iron
Casing
Casing
125 LB. ANSI
250 LB. ANSI
Drilling
Drilling
E-E
C-C
E-E
C-C
E-E
D-D
E-E
H-H
E-E
D-D
E-E
C-C
E-E
D-D
E-E
C-C
E-E
C-C
E-E
D-D
E-E
D-D
E-E
J-J
E-E
D-D
E-E
D-D
E-E
C-C
E-E
D-D
E-E
D-D
E-E
D-D
E-E
C-C
E-E
C-C
E-E
D-D
E-E
D-D
E-E
R.F.
E-E
D-D
AE PRESSURE-TEMPERATURE
LIMITATION CURVES
Ductile Iron
Casing
250 LB. ANSI
Drilling
N.A.
L-L
N.A.
B-B
N.A.
A-A
N.A.
A-A
A-A
N.A.
N.A
A-A
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
TABLE B
(Maximum Suction Pressure
Pump Size &
Type
2AE11
3AE9
3AE14, G
4AE10, G
4AE11, G
4AE12
5AE8, N
5AE11, G
5AE12
5AE14, G, N
6AE11
6AE12
6AE14, G, N
6AE16G, N, V
6AE18
8AE12
8AE13
8AE15, G
8AE17A, Q, W
8AE20, G
10AE12
10AE14A, J
10AE16
10AE20
SUCTION FLANGE
Cast Iron Casing or Ductile Casing
125 LB. ANSI Drilling
250 LB. ANSI Drilling
E-E
R.F.
E-E
D-D
E-E
R.F.
E-E
D-D
E-E
D-D
E-E
D-D
E-E
R.F.
E-E
C-C
E-E
C-C
E-E
R.F.
E-E
D-D
E-E
D-D
E-E
D-D
E-E
R.F.
E-E
R.F.
E-E
E-E
E-E
E-E
E-E
E-E
F-F
F-F
F-F
R.F.
E-E
D-D
F-F
F-F
E-E
R.F.
E-E
R.F.
N.A. = Not Available
R.F. = Refer to the factory
4852154
Rev. 12-89
Subject to change without notice
SECTION 1220
Page 2.2
June 1, 2004
Peerless Pump Company
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE DOUBLE SUCTION
Indianapolis, IN 46207-7026
Type AE
Pump Data
Nom.
Casing
Thickness
Inches
Corrosion
Allowance
Inches
First
Critical
Speed
rpm
2AE11 c
3AE9
3AE9G
3AE14
3AE14G
.44
.12
6136
.38
.38
.47
.47
.12
.12
.12
.12
5734
5734
5090
5090
4AE10
4AE10G
4AE11
4AE11G
.40
.40
.38
.38
.50
.12
.12
.12
.12
.12
5175
5175
6388
6388
6910
.38
.38
.50
.50
.56
.50
.50
.50
.12
.12
.12
.12
.12
.12
.12
.12
6830
6830
5902
5902
6100
4196
4196
4196
6AE11
6AE12 d
6AE14
6AE14G
6AE14N
6AE16
6AE16G
6AE16N
6AE16V
6AE18
.38
.66
.56
.56
.56
.56
.56
.56
.56
.69
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
6388
6308
4611
4611
4534
3841
3841
3841
3841
4034
8AE12
8AE13
8AE15
8AE15G
.44
.50
.56
.56
.62
.62
.62
.69
.69
.56
.62
.62
.75
.75
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
.12
6024
4206
6013
6013
3649
3649
3649
3649
3649
4799
4052
4052
3873
3251
Pump Size &
Type
4AE12 d
5AE8
5AE8N
5AE11
5AE11G
5AE12 d
5AE14
5AE14G
5AE14N
8AE17A d
8AE17Q d
8AE17W d
8AE20
8AE20G
10AE12
10AE14A d
10AE14J d
10AE16 d
10AE20 d
No. of
Imp.
Vanes
Prime. or
Csg. Vent
Conn.
NPT Size
Disch.
Drain
NPT
Size
Suct
Drain
NPT
Size
3600
4
1/2
1/2
1/2
Imp.
1.375
Cplg.
1.125
11.00
1.3
7.00
3600
3600
2300 f
2400 f
3600
3600
2000 f
2100 f
3600
6
6
5
6
1/2
1/2
1/2
1/2
3/4
3/4
1/2
1/2
1/2
1/2
1/2
1/2
1.625
1.625
1.375
1.375
1.375
1.375
1.125
1.125
9.56
9.56
14.50
14.50
1.2
1.3
3.0
1.7
6.13
6.25
9.75
9.00
6
6
8
6
7
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
1/2
1/2
1/2
1/2
1/2
1.625
1.625
1.375
1.375
1.625
1.375
1.375
1.125
1.125
1.375
10.38
10.38
11.91
11.91
12.58
1.7
1.2
1.8
2.0
2.4
7.00
6.13
7.62
7.62
8.50
6
8
8
8
6
8
8
6
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
3/4
3/4
1
1
1
3/4
3/4
3/4
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1.625
1.625
1.750
1.750
1.750
1.625
1.625
1.625
1.375
1.375
1.562
1.562
1.562
1.375
1.375
1.375
8.42
8.42
11.62
11.62
13.00
14.62
14.62
14.62
1.5
1.3
1.9
1.9
2.9
5.7
3.6
3.1
5.75
5.75
7.50
7.50
8.50
10.00
10.00
10.00
5
7
8
8
8
8
8
6
8
8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
1
1
1
1
1
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1.375
2.125
1.750
1.750
1.750
1.750
1.750
1.750
1.750
2.125
1.125
1.875
1.562
1.562
1.562
1.562
1.562
1.562
1.562
1.875
11.29
13.00
15.66
15.66
15.66
17.41
17.41
17.41
17.41
18.15
2.1
5.5
5.0
4.7
7.9
7.5
7.3
7.7
9.5
14.7
5
8
7
8
8
8
8
8
8
8
8
8
8
7
1/2
1
1
1
1
1
1
1
1
1
1
1
1
1
1/2
1
3/4
3/4
1
1
1
1
1
1
1
1
1
1
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1
1.750
1.750
2.125
2.125
2.125
2.125
2.125
2.500
2.500
2.125
2.500
2.500
2.500
2.750
1.562
1.562
1.875
1.875
1.875
1.875
1.875
2.250
2.250
1.875
2.250
2.250
2.250
2.500
13.10
13.72
16.38
16.38
18.90
18.90
18.90
20.84
20.84
12.74
15.08
15.08
17.00
21.25
3.3
8.6
8.8
8.4
12.1
11.8
12.8
22.0
29.9
7.4
16.0
16.6
22.9
37.4
Max
Pump
Speed
rpm.
3600
3600
3600
3600
3600
2000 f
2100 f
2100 f
1800
3600
1800
1800
1800
1800
1800
1800
1800
1900 f
1800
1800
1800
1900 f
1800
1800
1800
2000 f
1800
1800
2000 f
2100 f
1800
1900 f
Shaft Diameter
Through (Inches)
Cutwater
Dia.
In.
WR2
Lb-Ft2
(Wet.
Brz.
Imp.)
Min. Imp.
Dia. In.
7.00
e 8.50
10.00
10.00
11.00
12.00
12.00
12.00
12.00
13.00
e 8.00
9.00
e 10.25
e 10.25
12.00
12.00
12.00
14.00
14.00
e 9.00
e 10.00
e 10.00
11.50
15.00
c Single Suction Design d Double Volute Casing e Average Diameter
f For applications where speeds exceed 4 pole motor speeds (1800 rpm), these must be reviewed by factory application department as
special pump construction may be required which may result in price additions for the special construction, refer to the factory for these
applications.
See Page 2.21 for continuation of data
Subject to change without notice
Peerless Pump Company
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE DOUBLE SUCTION
Type AE
Indianapolis, IN 46207-7026
SECTION 1220
Page 2.21
June 1, 2004
Pump Data-Continued
Pump Size
& Type
2AE11
3AE9
3AE9G
3AE14
3AE14G
4AE10
4AE10G
4AE11
4AE11G
4AE12
5AE8
5AE8N
5AE11
5AE11G
5AE12
5AE14
5AE14G
5AE14N
6AE11
6AE12
6AE14
6AE14G
6AE14N
6AE16
6AE16G
6AE16N
6AE16V
6AE18
8AE12
8AE13
8AE15
8AE15G
8AE17A
8AE17Q
8AE17W
8AE20
8AE20G
10AE12
10AE14A
10AE14J
10AE16
10AE20
Shaft
Sleeve
Dia.
Inches
1.500
1.750
1.750
1.500
1.500
1.750
1.750
1.500
1.500
1.750
1.750
1.750
2.000
2.000
2.000
1.750
1.750
1.750
1.500
2.375
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.375
2.000
2.000
2.375
2.375
2.375
2.375
2.375
2.750
2.750
2.375
2.750
2.750
2.750
3.125
Bore
Inches
2.375
2.750
2.750
2.375
2.375
2.750
2.750
2.375
2.375
2.750
2.750
2.750
3.000
3.000
3.000
2.750
2.750
2.750
2.375
3.500
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.500
3.000
3.000
3.500
3.500
3.500
3.500
3.500
4.000
4.000
3.500
4.000
4.000
4.000
4.375
Depth
Inches
2.94
3.31
3.31
2.94
2.94
3.31
3.31
2.94
2.94
3.31
3.31
3.31
3.31
3.31
3.31
3.31
3.31
3.31
2.94
3.75
3.31
3.31
3.31
3.31
3.31
3.31
3.31
3.75
3.31
3.31
3.75
3.75
3.75
3.75
3.75
4.12
4.12
3.75
4.12
4.12
4.12
4.62
Stuffing Box
Face to
Packing
Nearest
Size ObstrucSquare
tion on
Inches
Shaft
Inches
1.63
1.82
1.82
1.63
1.63
1.82
1.82
1.38
1.38
1.82
2.01
2.01
1.68
1.68
1.74
1.82
1.82
1.82
1.38
2.20
1.76
1.76
1.76
1.74
1.74
1.74
1.74
2.19
1.74
1.74
2.20
2.20
2.19
2.19
2.19
2.44
2.44
2.23
2.44
2.44
2.44
3.06
7/16
1/2
1/2
7/16
7/16
1/2
1/2
7/16
7/16
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
7/16
9/16
1/2
1/2
1/2
1/2
1/2
1/2
1/2
9/16
1/2
1/2
9/16
9/16
9/16
9/16
9/16
5/8
5/8
9/16
5/8
5/8
5/8
5/8
Number
of Rows
of
Packing
Each Box
f
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Gland
Bolt
Circle
Dia.
Inches
Two @
180o
Apart
4.50
4.75
4.75
4.50
4.50
4.75
4.75
4.50
4.50
4.75
4.75
4.75
5.25
5.25
5.25
4.75
4.75
4.75
4.50
6.25
5.25
5.25
5.25
5.25
5.25
5.25
5.25
6.25
5.25
5.25
6.25
6.25
6.25
6.25
6.25
7.50
7.50
6.25
7.50
7.50
7.50
7.50
Gland
Bolt Dia.
Inches
3/8
1/2
1/2
3/8
3/8
1/2
1/2
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
3/8
5/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
Bearing Size
Thrust
Radial
(Single
(Single
Row)
Row)
305
306
306
305
305
306
306
305
305
306
306
306
307
307
307
306
306
306
305
308
307
307
307
307
307
307
307
308
307
307
308
308
308
308
308
310
310
308
310
310
310
311
206
207
207
206
206
207
207
206
206
207
207
207
208
208
208
207
207
207
206
210
208
208
208
208
208
208
208
210
208
208
210
210
210
210
210
212
212
210
212
212
212
213
Distance
Between
Bearing
Centers
Inches
18.75
20.00
20.00
18.75
18.75
20.00
20.00
18.75
18.75
20.00
21.75
21.75
22.00
22.00
22.00
23.25
23.25
23.25
18.75
25.50
23.37
23.37
23.37
26.12
26.12
26.12
26.12
27.00
22.00
24.00
25.50
25.50
27.00
27.00
27.00
33.50
33.50
28.34
33.50
33.50
33.50
37.00
f Five with Optional Lantern Ring
Subject to change without notice
Peerless Pump Company
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE DOUBLE SUCTION
Type AE
SECTION 1220
Page 2.22
June 1, 2004
Indianapolis, IN 46207-7026
Speed - Torque Curve
100
90
80
% Torque
70
60
50
40
30
20
10
0
0
10
20
30
40
50 60
% Speed
70
80
90 100
Information required to use speed-torque curve
1 - 100% of Torque =
2 - 100% of Speed =
Ft.-lbs @
Gpm
Total Head Feet
Rpm (true running speed)
To determine 100% of torque in Ft.-Lbs., use the following equation:
100% torque (Ft.-Lbs) =
BHP c x 5250
RPM (true running speed)
c For open valve starting - use BHP at design point
For closed valve starting - use BHP at shut-off point
Subject to change without notice
Peerless Pump Company
Indianapolis, IN 46207-7026
SECTION 1220
Page 3
December 1, 1989
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE SINGLE SUCTION
Type AE
Packed Type
Cross Sectional Drawing
BRONZE FITTED AE PUMP STANDARD MATERIALS OF CONSTRUCTION
Item
No.
1A,1B
2
6
7
8
13
14,14A
14B
16
17
Description
Upper & Lower Casings
Impeller
Shaft
Casing Ring
Impeller Ring (Optional)
Packing Ring
Shaft Sleeve
Shaft Sleeve '*O' Ring
Inboard Ball Bearing
Packing Gland
17A
17B
18
18A
29
31
Material
Cast Iron
Bronze
Steel c
Bronze c
Bronze c
Graphited TFE
Bronze c
Buna-N Rubber
Steel Assembly
Bronze d
Item
No.
32
33
35
37
40A
40B
41
43
46
47
Description
Impeller Key
Outboard Bearing Housing
Inb. Brg. Housing Cover
Out. Brg. Housing Cover
Inboard Deflector
Outboard Deflector
Inb.Brg. Housing Cap
Out. Brg Housing Cap
Coupling Key
Inb. Brg. Cover Seal
Gland Clip (when used)
Gland Bolt
Outboard Ball Bearing
Bearing Retaining Ring
Lantern Ring (Optional)
Stainless Steel
Steel
Steel Assembly
Steel
TFE
63
73A
73B
123
127
Stuffing Box Bushing
Casing Gasket (Not Shown)
Bearing Cover Gasket
Bearing End Cover
Water Seal Piping (Optional)
Inboard Bearing Housing
Cast Iron
169
Bearing Housing Seal
Material
Stainless Steel
Cast Iron
Cast Iron
Cast Iron
Rubber
Rubber
Cast Iron
Cast Iron
Steel
Steel/Rubber
Assembly
Bronze
Vegetable Fiber
Flber
Steel
Copper with Brass
Fittings
Steel/Rubber
Assembly
c Optional Material AISI 416 Stn. Stl. d Optional Material 316 Stn. Stl.
Subject to change without notice
SECTION 1220
Page 4
October 26, 1990
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE SINGLE SUCTION
Type AE
Peerless Pump Company
Indianapolis, IN 46206-7026
Mechanical Seal Type
Cross Sectional Drawing
BRONZE FITTED AE PUMP STANDARD MATERIALS OF CONSTRUCTION
Item
No.
1A,1B
2
6
7
8
14,14A
Description
Material
Upper & Lower Casings
Impeller
Shaft
Casing Ring
Impeller Ring (Optional)
Shaft Sleeve
Cast Iron
Bronze
Steel c
Bronze c
Bronze
Bronze c
14B
16
17
17B
17B
18
18A
31
32
33
35
Shaft Sleeve '*O' Ring
Inboard Ball Bearing
Mechanical Seal Flange
Gland Bolt
Seal Flange "O" Ring
Outboard Ball Bearing
Bearing Retaining Ring
Inboard Bearing Housing
Impeller Key
Outboard Bearing Housing
Inb. Brg. Housing Cover
Buna-N Rubber
Steel Assembly
Cast Iron
Steel
Buna N Rubber
Steel Assembly
Steel
Cast Iron
Stainless Steel
Cast Iron
Cast Iron
37
Out. Brg. Housing Cover
Cast Iron
Item
No.
40A
40B
41
43
46
47
73A
73B
65
80
80A
123
169
Description
Inboard Deflector
Outboard Deflector
Inb.Brg. Housing Cap
Out. Brg Housing Cap
Coupling Key
Inb. Brg. Cover Seal
Casing Gasket (Not Shown)
Bearing Cover Gasket
Mechanical Seal Seat
Flexible
Mechanical
Washer
Seal
Metal
Rotary
Spring
Bellows
Shaft Collar
Bearing End Cover
Bearing Housing Seal
Material
Rubber
Rubber
Cast Iron
Cast Iron
Steel
Steel/Rubber
Assembly
Vegetable Fiber
Flber
Ni-Resist
Buna Rubber
Carbon
18-8 Stn. Stl.
18-8 Stn. Stl.
Buna Rubber
18-8 Stn. Stl.
Steel
Steel/Rubber
Assembly
c Optional Material AISI 416 Stn. Stl.
Subject to change without notice
Peerless Pump Company
Indianapolis, IN 46207-7026
SECTION 1220
Page 5
December 1, 1989
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE SINGLE SUCTION
Type AE
Packed Type
Cross Sectional Drawing
ALL IRON AE PUMP STANDARD MATERIALS OF CONSTRUCTION
Item
No.
1A,1B
2
6
7
8
13
14,14A
14B
16
17
Description
Upper & Lower Casings
Impeller
Shaft
Casing Ring
Impeller Ring (Optional)
Packing Ring
Shaft Sleeve
Shaft Sleeve '*O' Ring
Inboard Ball Bearing
Packing Gland
17A
17B
18
18A
29
31
Material
Cast Iron
Cast Iron
Steel c
Cast Iron c
Steel c
Graphited TFE
AISI 416 Stn. Steel
Buna-N Rubber
Steel Assembly
316 Stn. Steel
Item
No.
32
33
35
37
40A
40B
41
43
46
47
Description
Impeller Key
Outboard Bearing Housing
Inb. Brg. Housing Cover
Out. Brg. Housing Cover
Inboard Deflector
Outboard Deflector
Inb.Brg. Housing Cap
Out. Brg Housing Cap
Coupling Key
Inb. Brg. Cover Seal
Gland Clip (when used)
Gland Bolt
Outboard Ball Bearing
Bearing Retaining Ring
Lantern Ring (Optional)
Stainless Steel
Steel
Steel Assembly
Steel
TFE
63
73A
73B
123
127
Stuffing Box Bushing
Casing Gasket (Not Shown)
Bearing Cover Gasket
Bearing End Cover
Water Seal Piping (Optional)
Inboard Bearing Housing
Cast Iron
169
Bearing Housing Seal
Material
Stainless Steel
Cast Iron
Cast Iron
Cast Iron
Rubber
Rubber
Cast Iron
Cast Iron
Steel
Steel/Rubber
Assembly
Steel
Vegetable Fiber
Flber
Steel
Steel with Steel
Fittings
Steel/Rubber
Assembly
c Optional Material AISI 416 Stn. Stl.
Subject to change without notice
Peerless Pump Company
Indianapolis, IN 46207-7026
SECTION 1220
Page 9
October 26, 1990
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE SINGLE SUCTION
Type AE
Packed Type
Oil Lubricated Bearings
Cross Sectional Drawing
ALL IRON AE PUMP STANDARD MATERIALS OF CONSTRUCTION
Item
No.
1A,1B
2
6
7
8
13
14,14A
14B
16
17
Description
Upper & Lower Casings
Impeller
Shaft
Casing Ring
Impeller Ring (Optional)
Packing Ring
Shaft Sleeve
Shaft Sleeve '*O' Ring
Inboard Ball Bearing
Packing Gland
17A
17B
18
18A
29
31
Material
Cast Iron
Cast Iron
Steel c
Cast Iron c
Steel c
Graphited TFE
AISI 416 Stn. Stl.
Buna-N Rubber
Steel Assembly
316 Stn. Stl.
Item
No.
32
33
35
37
40A
40B
41
43
46
47
Description
Impeller Key
Outboard Bearing Housing
Inb. Brg. Housing Cover
Out. Brg. Housing Cover
Inboard Deflector
Outboard Deflector
Inb.Brg. Housing Cap
Out. Brg Housing Cap
Coupling Key
Inb. Brg. Cover Seal
Gland Clip (when used)
Gland Bolt
Outboard Ball Bearing
Bearing Retaining Ring
Lantern Ring (Optional)
Stainless Steel
Steel
Steel Assembly
Steel
TFE
63
73A
73B
123
127
Stuffing Box Bushing
Casing Gasket (Not Shown)
Bearing Cover Gasket
Bearing End Cover
Water Seal Piping (Optional)
Inboard Bearing Housing
Cast Iron
169
Bearing Housing Seal
Material
Stainless Steel
Cast Iron
Cast Iron
Cast Iron
Rubber
Rubber
Cast Iron
Cast Iron
Steel
Steel/Rubber
Assembly
Steel
Vegetable Fiber
Flber
Steel
Steel with Steel
Fittings
Steel/Rubber
Assembly
c Optional Material AISI 416 Stn. Stl.
Subject to change without notice
Peerless Pump Company
Indianapolis, IN 46207-7026
SECTION 1220
Page 11
June 15, 1992
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE DOUBLE SUCTION
Type AE
Packed Type with Double Row Thrust Bearing
Cross Sectional Drawing
4852867
BRONZE FITTED AE PUMP STANDARD MATERIALS OF CONSTRUCTION
Item
No.
1A,1B
2
6
7
8
13
14,14A
14B
16
17
Description
Upper & Lower Casings
Impeller
Shaft
Casing Ring
Impeller Ring (Optional)
Packing Ring
Shaft Sleeve
Shaft Sleeve '*O' Ring
Inboard Ball Bearing
Packing Gland
17A
17B
18
18A
22
Material
Cast Iron
Bronze
Steel c
Bronze c
Bronze
Graphited TFE
Bronze c
Buna-N Rubber
Steel Assembly
Bronze d
Item
No.
32
33
35
37
40A
40B
41
43
46
47
Description
Impeller Key
Outboard Bearing Housing
Inb. Brg. Housing Cover
Out. Brg. Housing Cover
Inboard Deflector
Outboard Deflector
Inb.Brg. Housing Cap
Out. Brg Housing Cap
Coupling Key
Inb. Brg. Cover Seal
Gland Clip (when used)
Gland Bolt
Outboard Ball Bearing
Bearing Lock Washer
Bearing Lock Nut
Stainless Steel
Steel
Steel Assembly
Steel
Steel
63
73A
73B
123
127
Stuffing Box Bushing
Casing Gasket (Not Shown)
Bearing Cover Gasket
Bearing End Cover
Water Seal Piping (Optional)
29
Lantern Ring (Optional)
TFE
169
Bearing Housing Seal
31
Inboard Bearing Housing
Cast Iron
Material
Stainless Steel
Cast Iron
Cast Iron
Cast Iron
Rubber
Rubber
Cast Iron
Cast Iron
Steel
Steel/Rubber
Assembly
Bronze
Vegetable Fiber
Flber
Steel
Copper with Brass
Fittings
Steel/Rubber
Assembly
c Optional Material AISI 416 Stn. Stl. d Optional Material 316 Stn. Stl.
Subject to change without notice
SECTION 1220
Page 12
June 15, 1992
Peerless Pump Company
HORIZONTAL SPLIT CASE PUMPS
SINGLE STAGE DOUBLE SUCTION
Type AE
Indianapolis, IN 46207-7026
Mechanical Seal Type with
Double Row Thrust Bearing Cross Sectional Drawing
BRONZE FITTED AE PUMP STANDARD MATERIALS OF CONSTRUCTION
Item
No.
1A,1B
2
6
Description
Material
Upper & Lower Casings
Impeller
Shaft
Cast Iron
Bronze
7
Casing Ring
Bronze c
8
Impeller Ring (Optional)
14,14A
Shaft Sleeve
14B
Item
No.
37
40A
40B
Description
Material
Out. Brg. Housing Cover
Inboard Deflector
Outboard Deflector
Cast Iron
Rubber
Rubber
41
Inb.Brg. Housing Cap
Cast Iron
Bronze c
43
Out. Brg Housing Cap
Cast Iron
46
Coupling Key
Steel
Shaft Sleeve '*O' Ring
Bronze c
Buna-N Rubber
47
Inb. Brg. Cover Seal
16
17
17B
17B
18
18A
22
31
32
Inboard Ball Bearing
Mechanical Seal Flange
Gland Bolt
Seal Flange "O" Ring
Outboard Ball Bearing
Bearing Lock Washer
Bearing Lock Nut
Inboard Bearing Housing
Impeller Key
Steel Assembly
Cast Iron
Steel
Buna N Rubber
Steel Assembly
Steel
Steel
Cast Iron
Stainless Steel
73A
73B
65
80A
Casing Gasket (Not Shown)
Bearing Cover Gasket
Mechanical Seal Seat
Flexible
Mechanical
Washer
Seal
Metal
Rotary
Spring
Bellows
Shaft Collar
Steel/Rubber
Assembly
Vegetable Fiber
Flber
Ni-Resist
Buna Rubber
Carbon
18-8 Stn. Stl.
18-8 Stn. Stl.
Buna Rubber
18-8 Stn. Stl.
33
Outboard Bearing Housing
Cast Iron
123
Bearing End Cover
Steel
35
Inb. Brg. Housing Cover
Cast Iron
169
Bearing Housing Seal
Steel/Rubber
Assembly
Steel c
80
c Optional Material AISI 416 Stn. Stl.
Subject to change without notice