Form No. 101429 ® Parts List for: SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031 P300 SERIES P300E P300N P300V Internet Address: http://www.powerteam.com MODEL B TWO-SPEED HYDRAULIC HAND PUMP Max. Capacity: 10,000 PSI 1 "A" 2 "C" GAUGE 3 4 "B" "B" PRESSURE "C" 6 7 8, 9 ATTENTION "A" 30¡ 60¡ 31 5 15 32 10 11 14 13 12 15 16 17 18 33 30 29 28 27 © SPX Corporation 26 25 24 23 22 21 20 19 16 Sheet No. 1 of 2 Rev. 5 Date: 2 Dec. 1999 Parts List, Form No. 101429, Back sheet 1 of 2 Item No. Part No. No. Req’d Description 1 2 3 4 5 6 7 251564 •†*215907 14972 215300 215301 211742 211743 4 2 1 1 1 2 4 Cap Screw (1/4-20 UNC X 3/4 Lg.) Decal Pipe Plug (1/4 NPTF) Decal Pressure Decal Dowel Pin Retaining Ring (Note: Expand retaining ring 8 9 21643 10556 1 2 Valve Release Handle Set Screw (1/4-20 UNC X 1/4 Lg.; 10 11 12 61806OR9 27142 *10527 †11450 •17723 350923 58485WH2 *15092 †19321 •250841 *10271 1 1 1 1 1 1 1 1 1 1 3 Handle Assembly Filler Plug O-ring (Nitrile; 13/16 X .644 X .087) O-ring (Viton; 13/16 X .644 X .087) O-ring (EPR; 13/16 X .644 X .087) Piston Clip Cap (Iron) Rod Wiper (Nitrile) Rod Wiper (Viton) Rod Wiper (EPR) O-ring (11/16 X 1/2 X 3/32; †11445 •19406 *251603 †18985 •251604 253268 •†*213987 3 3 1 1 1 1 1 O-ring (Viton; 11/16 X 1/2 X 3/32) O-ring (EPR; 11/16 X 1/2 X 3/32) O-ring (2-1/8 x 2" x 1/16) O-ring (Viton; 2-1/8 x 2" x 1/16) O-ring (EPR; 2-1/8 x 2" x 1/16) Piston Assembly Backup Washer (11/16 X 1/2 X 3/64; 64597 *214693 †19048 •214072 10427 •†*215075 21278 309221CE 64487 251382 10842 *251348 †251355 12042 •†*305977 211769 253234 *10294 †11447 •215366 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 to .440 max. dia. during installation.) 13 14 15 16 Note: Screw in valve stem [Item 10 on sheet 2 of 2] until seated [bottomed out]. Then position knob as shown approx. 1/16” from casting surface. Lock in place with set screws. Torque to 50/70 in. lbs.) Included with piston assembly Item #16) 17 18 19 Note: Assemble with concave surface towards o-ring.) 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Pump Body O-ring (3-7/8 X 3-5/8 X 1/8) O-ring (Viton; 3-7/8 X 3-5/8 X 1/8) O-ring (EPR; 3-7/8 X 3-5/8 X 1/8) Pressure Plug (1/8 NPTF) Filter Relief Valve Assembly (See note below) Trade Name Decal Reservoir Assembly Tie Rod (Note: Screw in tie rod until it bottoms out in pump body.) Cap Nut Seal Washer Seal Washer (Viton) Copper Washer (To be used on pumps with EPR seals) Warning Decal Handle Grip Decal, Oil Pivot Pins O-ring (2.00 x 1.75 Nitrile) Note: Shaded O-ring (2.00 x 1.75 Viton) areas reflect last O-ring (2.00 x 1.75 EPR) revision(s) made to this form. PARTS INCLUDED BUT NOT SHOWN †205724 1 Decal (Viton seals) •250328 1 Decal (EPR seals) 253300 1 Seal Washer (For sight gauge on reservoir assembly.) Part numbers marked with an asterisk (*) are contained in Standard Repair Kit No. 300695. Part numbers marked with a dagger (†) are contained in Viton Seal Kit No. 300696. Part numbers marked with a bullet (•) are contained in EPR Seal Kit No. 300697. NOTE: Standard relief valves are set at 10,000/10,700 PSI. Relief valves pre-set at special settings are available. Refer to your pump model number or contact Power Team Technical Services. Parts List Form No. 101429 SECTIONS A-A, B-B, & C-C 3 4 5 6 7 6 2 1 8 11 9 9 10 22 12 13 20 21 19 14 18 17 5 3 16 15 6 7 9 Sheet No. 2 of 2 Rev. 5 Date: 2 Dec. 1999 Parts List, Form No. 101429, Back sheet 2 of 2 Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Part No. No. Req’d Description •†*15085 *10267 †18974 •13472 351952 17586 •†*14874 •†*10444 •†*10378 •†*211797 •†*10375 350185 14763 14588 252275 1 1 1 1 2 1 2 3 2 1 3 1 1 1 1 Backup Washer (7/16 X 5/16 X 3/64 Thk.) O-ring (7/16 X 5/16 X 1/16) O-ring (Viton; 7/16 X 5/16 X 1/16) O-ring (EPR; 7/16 X 5/16 X 1/16) Valve Screw (Torque to 350/370 in. lbs.) Sight Gauge Soft Copper Washer (.700 X 1/2 X 1/32) Compression Spring (3/16 I.D. X 13/32 Lg.) Steel Ball (3/8 Dia.) Spring (5/32 O.D. X 5/8 Lg.) Steel Ball (1/4 Dia.) Release Valve Screw O-ring (.43 x .31; Urethane) Dowel Pin Unloading Valve Piston Kit (Includes retaining ring [Item #21] 11127 *10265 †11437 •17714 •†*15174 214692 *12557 †18973 •215375 308430 214694 252273 10714 1 1 1 1 1 1 1 1 1 1 1 1 1 Pressure Plug (3/8 NPTF) O-ring (5/16 X 3/16 X 1/16) O-ring (Viton; 5/16 X 3/16 X 1/16) O-ring (EPR; 5/16 X 3/16 X 1/16) Backup Ring (5/16 X 3/16 X 3/64) Disc O-ring (11/32 X 7/32 X 1/16) O-ring (Viton; 11/32 X 7/32 X 1/16) O-ring (EPR; 11/32 X 7/32 X 1/16) Unloading Valve Fitting Compression Spring (1/2 O.D. X 2-1/8 Lg.) Retaining Ring (Included in unloading valve piston kit [Item #13].) Slotted Spring Pin (.19 x .63) and unloading valve piston) 14 15 16 17 18 19 20 21 22 Part numbers marked with an asterisk (*) are contained in Standard Repair Kit No. 300695. Part numbers marked with a dagger (†) are contained in Viton Seal Kit No. 300696. Part numbers marked with a bullet (•) are contained in EPR Seal Kit No. 300697. Refer to any operating instructions included with this product for detailed information about operation, testing, disassembly, reassembly and preventive maintenance. Items found in this parts list have been carefully tested and selected. Therefore: Use only genuine Power Team replacement parts! Additional questions can be directed to our Technical Services Department.