6000 Series Two-Piece Metal Raceway Installation

Wiremold Electrical Systems conform to and should be installed and
properly grounded in compliance with requirements of the current
National Electrical Code, Canadian Electrical Code or codes administered by local authorities.
All electrical products may represent possible shock or fire hazard if
improperly installed or used. Wiremold electrical products are UL listed.
Made for interior use only and should be installed in conformance with
current local and/or the National Electrical Code.
6000 Two-Piece Metal Raceway
INSTALLATION INSTRUCTIONS
6000 RACEWAY WIRE FILL CAPACITIES FOR DATA/COMMUNICATIONS
UNSHIELDED
TWISTED PAIR
24 AWG, 4-PAIR
TYPE
CAT. 5
0.220
[5.6]
80
161
O.D. inches
O.D. [mm]
40% fill, divided
40% fill, undivided
CAT. 3
0.190
[4.8]
107
217
TELEPHONE
24 AWG, NO. OF PAIRS
2
0.140
[3.6]
198
399
3
0.150
[3.8]
172
348
4
0.190
[4.8]
107
217
COAXIAL
25
0.410
[10.4]
23
46
RG58/U
0.195
[5.0]
102
206
RG59/U
0.242
[6.1]
66
133
SHIELDED
TWISTED
PAIR
TWINAXIAL
RG62/U
0.242
[6.1]
66
133
RG6/U
0.270
[6.9]
53
107
100 OHM
0.330
[8.4]
35
71
TYPE 1
0.390
[9.9]
25
51
TYPE 2
0.465
[11.8]
17
36
TYPE 3
0.245
[6.2]
64
139
FIBER OPTIC
TWO STRAND (DUPLEX)
MULTIMODE, 62.5/125µm
0.190
[4.8]
107
217
6000 RACEWAY WIRE FILL CAPACITIES FOR POWER
TYPE AWG, THHN/THWN
O.D. inches
O.D. [mm]
40% fill, divided
40% fill, undivided
2/0
.532
13.5
14
28
1/0
.486
12.3
17
34
1
.446
11.3
20
40
WITHOUT DEVICES
2
4
6
0.384 0.324 0.254
9.8
8.2
6.5
27
38
62
54
76
125
8
0.216
5.5
86
173
10
12
0.164 0.130
4.2
3.3
149
237
300
475
14
0.111
2.8
325
652
2/0
.532
13.5
11
22
1/0
.486
12.3
14
26
1
.446
11.3
16
31
WITH DEVICES (SURGE / GFCI)
2
4
6
8
10
0.384 0.324 0.254 0.216 0.164
9.8
8.2
6.5
5.5
4.2
22
31
51
71
123
43
60
98
135
235
12
14
0.130 0.111
3.3
2.8
195
268
373
512
• Use No. 8 (5/16", 7.9mm head size) flat head fastener or equivalent to
mount base to surface.
• Grounding: Use ground location when provided or install a suitable
ground lug, ring terminal or locknut and ground bushing.
• Utiliser une attache à tête plate de calibre 8 (tête de 7.9mm, 5/16" po.)
ou une fixation équivalente pour assujettir le tube guide-fils et les raccords à la surface de montage.
• Mise à la terre: Utiliser l’emplacement de terre prévu ou poser le
matériel qui convient: patte de mise à la terre, cosse circulaire à oeil ou
écrou de blocage et manchon de terre.
• Use un sujetador de cabeza plana No. 8 (tamaño de cabeza: 7.9mm,
5/16" de pulgada) o su equivalente para unir la canalita y los accesorios a la superficie de montaje.
• Conexión a tierra: Use un localizador de tierra cuando se proporcione
o instale una orejeta de tierra, anillo terminal o contratuerca y cojinetes
de tierra apropiados.
660B
640C
6000B-10
6000C
6000WC
4000WC
18"
[45.7cm]
6001
6000DA / 6001DA
1
6006
2
3
6007C-2 / 6007C-1
1
2
3
6008A
1
2
3
60" max
[152cm]
4
6010B
6011TX
6011TX
1
1
2
Adjust
screws if
needed.
2
6001TX
1/2"
12.7mm
6000DA
2"
51mm
Wire Fill: 1/2 of values shown on page 1.
Wire Fill: 1/2 of values shown on page 1.
6012TX
6012TX
2
1
1
3
2
4
45°
45°
3
6014A
6017TX
6017TX
2
1
Adjust
screws if
needed.
3
1/2"
12.7mm
6000DA
2 1/2"
64mm
Wire Fill: 1/2 of values shown on page 1.
6017TX
3
2
1
1"
25mm
6000DA
2 3/4"
70mm
Wire Fill: 1/2 of values shown on page 1.
6086
6074A
6074
2
1
6046KD
1
2
Wire Capacity
Type
THHN, THWN
3
2/0
14
1/0
17
#1
20
4
#2
28
#3
33
Size AWG
#4
#6
39
64
5
#8
88
#10
153
#12
244
#14
334
The Wiremold Company
60 Woodlawn Street • West Hartford, CT 06110
1-800-621-0049 • Fax 860-232-2062
©1999 The Wiremold Company
41401R1 499