LD-BAR 12TC user manual - V1,0

ENGLISH
INSTALLATION MANUAL
SAFETY INSTRUCTIONS:
CAUTION
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol means: Safety Class III appliance
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
INSTALLATION MANUAL
INSTALLATION
CAUTION: To reduce the risk of electric shock, do not
remove the top cover. No user-serviceable parts inside.
Refer servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
•
•
ENGLISH
The device is suitable for mounting on standard flammable surfaces. Standard flammable
surfaces include building materials such as wood and wood-based materials more than 2mm
thick.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
This unit is for indoor use only.
Don’t place metal objects or spill liquid inside the unit. No objects filled with liquids, such as vases, shall be
placed on this appliance. Electric shock or malfunction may result. If a foreign object enters the unit,
immediately disconnect the mains power.
No naked flame sources, such as lighted candles, should be placed on the appliance.
Don’t cover any ventilation openings as this may result in overheating.
Prevent use in dusty environments and clean the unit regularly.
Keep the unit away from children.
Inexperienced persons should not operate this device.
Maximum save ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
Always unplug the unit when it is not used for a longer time or before you start servicing.
The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
Check that the available voltage is not higher than the one stated on the rear panel of the unit.
The socket inlet shall remain operable for disconnection from the mains.
The power cord should always be in perfect condition: switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard
Never let the power-cord come into contact with other cables!
This appliance must be earthed to in order comply with safety regulations.
In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user
serviceable parts inside.
Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
In the event of serious operating problems, stop using the appliance and contact your dealer immediately.
Please use the original packing when the device is to be transported.
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: The installation should be carried out by qualified personal only, according to the
regulations for electrical and mechanical safety in your country.
The LD-BAR12TC should be fixed on a non-flammable flat surface. For example you can fix the unit against
a wall using adapted screws. The orientation is not important but make sure that enough ventilation is
available.
! VERY IMPORTANT – READ IT BEFORE YOU CALL FOR HELP !
• This projector is only intended for use with the compatible LD-POWER power supplies: for
installation details and setup please also read the user manual for the LD-POWER power supply!
• Make sure the LD-POWER power supply is not connected to the mains during installation and
wiring!
• Make sure that the maximum load per LED output zone on the LD-POWER is not exceeded: this
means that only 1 LD-BAR 12TC can be connected to each RJ45-output of the power supplies!
• The maximum cable length between the LD-POWER output and all connected projectors is
80meters!
Electrical installation LED projector outputs:
The passive LED projectors from our LD-series use CAT5e cables and RJ45 connectors to connect them to
the LD-POWER power supplies. You can use our standard cables (“LD-PATCH RJ45”, available in different
lengths) but you can also make your own cables with CAT5e cable and RJ45 connectors you can buy from
any computer shop. However we like to warn you that
making your own cables is not easy and requires special
tools and some experience! The cables should be wired
1:1 (pins with same numbers connected together). The
maximum distance between the LD-POWER and the
LED-projectors is 80meters.
Wiring of the RJ45 connectors
Pin1: Red LED +
Pin2: Green LED +
Pin3: Blue LED +
Pin4: White LED +
Pin5: Red LED Pin6: Green LED Pin7: Blue LED Pin8: White LED -
Example of an installation
2 LD-BAR 12TC projectors connected to 2 different zone outputs of the LD-POWER 120. It’s important to
know that, since each output on the LD-POWER 120 supports up to 12 LEDs of each color, we are only
allowed to connect 1 LD-BAR 12TC to each output!
MAINTENANCE
Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside the unit. Do not
use volatile liquids such as benzene or thinner which will damage the unit.
BRITEQ®
2/4
LD-BAR 12TC
BRITEQ®
3/4
LD-BAR 12TC
ENGLISH
INSTALLATION MANUAL
ENGLISH
INSTALLATION MANUAL
SPECIFICATIONS
Input voltage:
Max input current:
Power consumption:
LED Emitters:
Beam Angle:
Compatible LED power supplies:
Cable type:
Cable length on the projector:
Max. cable length:
Size:
Weight:
DC 48V.
350mA
39,2W
3in1 3W RGB-leds
25° (standard, other beam angles on special order)
LD-POWER series
24AWG x 4P (Cat5e cable)
1,5m
80m
see drawings
2,4kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
OPERATION MANUAL
®
Thank you for buying this BRITEQ product from our Light Designer Series. To take full advantage of all
possibilities, please read these operating instructions very carefully.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
• This RGB-projector is designed for use in a wide range of indoor applications such as wall washing.
• Excellent light output and perfect color mixing thanks to Tri-color 3Watt RGB LEDs.
• Elegant, extruded aluminium housing finished with tempered glass cover
• The discretely designed bracket can be easily adjusted in any position.
• Optimal thermal management for long lifespan and easy maintenance
• Compatible with the “LD-POWER" power supplies
• Equipped with 1,5m CAT-5e cable and RJ45 connector.
• Light designers can download the photometric IES-files from our website for use in simulations
• Perfect for use in hotels, clubs, shops, homes, H
• 2 models available
BEFORE USE
Check the contents:
Check that the carton contains the following items:
• LD-BAR 12TC
• User manual
Some important instructions:
• Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
• Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
• Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
• To protect the environment, please try to recycle the packing material as much as possible.
BRITEQ®
4/4
LD-BAR 12TC
BRITEQ®
1/4
LD-BAR 12TC