Recuperación de un disco perdido en el conjunto de discos de Cisco Cache Engine Contenido Introducción prerrequisitos Requisitos Componentes Utilizados Convenciones Cómo leer la configuración Información Relacionada Introducción Este documento describe cómo recuperar un disco dentro de un conjunto de almacenamiento que ha perdido su sector de arranque en el Cisco Cache Engine. prerrequisitos Requisitos No hay requisitos específicos para este documento. Componentes Utilizados La información que contiene este documento se basa en las siguientes versiones de software y hardware. Cisco 590 Cache Engine en un ambiente de laboratorio con las configuraciones despejadas Socket de la Interfaz de sistema de computadoras pequeñas (SCSI) Conjunto de almacenamiento de Cisco Software Cisco Cache versión 2.3 La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener cualquier comando. Convenciones Para obtener más información sobre las convenciones del documento, consulte las Convenciones de Consejos Técnicos de Cisco. Cómo leer la configuración En esta configuración, el motor de 590 cachés conecta con un conjunto de almacenamiento a través del socket de SCSI. Memoria flash contiene el Software Cisco Cache versión 2.3. Initializing memory.� Please wait. Cisco Robin II:� Selected Console. BIOS Version: C9 BIOS Build date: 06/26/00 Symbios, Inc. SDMS (TM) V4.0 PCI SCSI BIOS, PCI Rev. 2.0, 2.1 Copyright 1995, 1998 Symbios, Inc. PCI-4.11.00 HBA ID LUN VENDOR�� PRODUCT��������� REV� SYNC WIDE INT13à --- -- --- -------- ---------------- ---- ---- ---- ----- -----------�0�� 0� 0� IBM����� DMVS18D������¢�0�� 1� 0� QUANTUM� VIKING II 9.1SCA 5520 80.0� 16�� 81h� 1024/255/6 �0�� 7� 0� Symbios� SYM53C895������� 0002 80.0� �0�� 8� 0� SEAGATE� ST318404LC������ 0002� NO�ï �0�� 9� 0� SEAGATE� ST318404LC������ 0002� NO�ï �0� 10� 0� SEAGATE� ST318404LC������ 0002� NO�� �0� 11� 0� SEAGATE� ST318404LC������ 0002� NO�� �0� 12� 0� SEAGATE� ST318404LC������ 0002� NO�� �0� 13� 0� SEAGATE� ST318404LC������ 0002� NO�� �0� 15� 0� EuroLogc ESM 0205� NO��� 8 El motor BIOS del caché ve todos los discos duros del conjunto de almacenamiento: Symbios, Inc. PCI boot ROM successfully installed! Cisco CE Booting From Flash. Cisco Cache Engine Boot. Version: 5.3.1 Creation date: May 2 2000, 11:49:05 Press any key to stop auto-boot... 0 auto-booting... boot device (flash,net) [ ; file name cache IP address [ IP network mask [ server IP address [ gateway IP address [ protocol (rcp,ftp,tftp) [ ; username ; password ; flags flash]: [ ce590-cache-230.bin]: 172.17.241.108]: 255.255.255.0]: 172.17.247.195]: 172.17.241.1]: tftp]: [ anonymous]: [ [email protected]]: [ 0]: Starting at 0x108000... #!ImageInfo # # +--------------------+ # | CISCO CE image | # +--------------------+ # SUPPORTED_PRODUCTS=CE590 UNCOMPRESSED_CKSUM=0x6925ea3 UNCOMPRESSED_SIZE=0x355198 COMPRESSED_CKSUM=0x9199a6d6 COMPRESSED_SIZE=0x167175 # Self decompressing the image : ########################################################################### ######################### [OK] Launching the image, please wait... .................. Console IO Initialized Attaching network interface lo0... done. ; Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause module_register_init name sym func 0x1ecdf8 data 0x44bb94 acompat_pci_handler: sym probing... 895: found t Fsym0: No NVRAM, ID 7, Fast-40, LVD, parity checking AR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. ; Cisco Systems, Inc. ; 170 West Tasman Drive ; San Jose, California 95134-1706 Cisco Content Engine Copyright (c) 1986-2000 by Cisco Systems, Inc. Software Release: CE ver 2.30 (Build: FCS 11/09/00) Compiled: 19:57:30 Nov 9 2000 by bbalagot Image text-base 0x108000, data_base 0x43515c System restarted by Power Up The system has been up for 6 seconds. System booted from "flash" SVCINIT - phase complete 895: attached unit 0 Waiting 2 seconds for SCSI devices to settle pt0 at sym0 bus 0 target 15 lun 0 pt0: <EuroLogc ESM 0205> Removable Processor SCSI-3 device pt0: 3.300MB/s transfers da0 at sym0 bus 0 target 0 lun 0 da0: <IBM DMVS18D 0100> Fixed Direct Access SCSI-3 device da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing En da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) da1 at sym0 bus 0 target 1 lun 0 da1: <QUANTUM VIKING II 9.1SCA 5520>Fixed Direct Access SCSI-2 device da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing En da1: 8709MB (17836668 512 byte sectors: 255H 63S/T 1110C) Esta lista contiene todos los discos duros del conjunto de almacenamiento que el driver SCSI del motor del caché encuentra: da6 at sym0 bus 0 target 12 lun 0 da6: <SEAGATE ST318404LC 0002> Fixed Direct Access SCSI-3 device da6: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing da6: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) da5 at sym0 bus 0 target 11 lun 0 da5: <SEAGATE ST318404LC 0002> Fixed Direct Access SCSI-3 device da5: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing da5: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) da4 at sym0 bus 0 target 10 lun 0 da4: <SEAGATE ST318404LC 0002> Fixed Direct Access SCSI-3 device da4: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing da4: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) da3 at sym0 bus 0 target 9 lun 0 da3: <SEAGATE ST318404LC 0002> Fixed Direct Access SCSI-3 device da3: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing da3: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) da2 at sym0 bus 0 target 8 lun 0 da2: <SEAGATE ST318404LC 0002> Fixed Direct Access SCSI-3 device da2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing da2: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) da7 at sym0 bus 0 target 13 lun 0 da7: <SEAGATE ST318404LC 0002> Fixed Direct Access SCSI-3 device da7: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing da7: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) En En En En En En Todas las unidades se reconocen correctamente. Abajo, la línea en la negrilla indica que el sistema operativo tiene un problema con el soporte de /c0t4d0s3. La estructura lógica del disco duro ha sido dañada. SCSI initialization complete DEVINIT - phase complete FSINIT - phase complete Configuring from NVRAM... Attaching network interface fei0... done. It is recommended to set restrictions that allow or deny HTTPS traffic to Destination Ports. Default settings may not provide the desired security le ----------------------------------------------------------- ----------"admin" super-user account is NOT password protected SECURITY ALERT: Please password protect the above super-user accounts! ----------------------------------------------------------- ----------CONF - phase complete NTP: Waiting (2 minutes) for network initialization SNMP: Waiting (2 minutes) for network initialization Fri Mar 24 13:31:00 2000: CFS volume /c0t4d0s3 mount failed S_partlib_INVALOTSECT Fri Mar 24 13:31:00 2000: dns-cache turned ONLINE due to dependency on nameer Aquí, el texto en la negrilla indica que el sector de arranque de este disco está perdido. Se pierde la estructura de la partición. START - phase complete Username: admin Password: Please set a password for this user account disaster# show disks �����/c0t0d0� �����/c0t1d0� �����/c0t2d0� �����/c0t3d0� �����/c0t4d0� �����/c0t5d0� to aid security! (scsi (scsi (scsi (scsi (scsi (scsi bus bus bus bus bus bus 0, 0, 0, 0, 0, 0, unit unit unit unit unit unit 0, 1, 2, 3, 4, 5, lun lun lun lun lun lun 0) 0) 0) 0) 0) 0) �����/c0t6d0� (scsi bus 0, unit 6, lun 0) �����/c0t7d0� (scsi bus 0, unit 7, lun 0) disaster# show disk-parti /c0t2d0 Disk size� : 35843670 sectors Partition 1: UNUSED,������� offset�������� Partition 2: CISCO_BFS_1,�� offset������� 10 sectors, size��ï Partition 3: CISCO_CFS_1,�� offset����� 1044 sectors, size� 35842616 sector Partition 4: UNUSED,������� offset�������� disaster# show disk-parti /c0t3d0 Disk size� : 35843670 sectors Partition 1: UNUSED,������� offset�������� Partition 2: CISCO_BFS_1,�� offset������� 10 sectors, size��ï Partition 3: CISCO_CFS_1,�� offset����� 1044 sectors, size� 35842616 sector Partition 4: UNUSED,������� offset�������� disaster# show disk-parti /c0t4d0 Unable to show disk partitions for /c0t4d0, errno S_partlib_INVALID_BOOTSEC � disaster# show disk-parti /c0t5d0 Disk size� : 35843670 sectors Partition 1: UNUSED,������� offset�������� Partition 2: CISCO_BFS_1,�� offset������� 10 sectors, size��ï Partition 3: CISCO_CFS_1,�� offset����� 1044 sectors, size� 35842616 sector Partition 4: UNUSED,������� offset�������� disaster# show disk-parti /c0t6d0 Disk size� : 35843670 sectors Partition 1: UNUSED,������� offset�������� Partition 2: CISCO_BFS_1,�� offset������� 10 sectors, size��ï Partition 3: CISCO_CFS_1,�� offset����� 1044 sectors, size� 35842616 sector Partition 4: UNUSED,������� offset�������� disaster# show disk-parti /c0t7d0 Disk size� : 35843670 sectors Partition 1: UNUSED,������� offset�������� Partition 2: CISCO_BFS_1,�� offset������� 10 sectors, size��ï Partition 3: CISCO_CFS_1,�� offset����� 1044 sectors, size� 35842616 sector Partition 4: UNUSED,������� offset�������� Usted necesita reconstruir la estructura de directorios con el comando disk manufacture. Este comando flexible crea la estructura de directorios correcta. También, cuando usted lo utiliza en /c0t0d0, crea el sistema de archivos DOS también. disaster# disk manufacture /c0t4d0 total size of disk = 35843670 CISCO_UVFAT_1 vol /c0t4d0s1 part_off 0 part_siz 0 Skipping creation of DOS partition for SCSI device Se salta la división DOS porque no es necesario. CISCO_BFS_1 vol /c0t4d0s2 part_off 10 part_siz 1024 CISCO_CFS_1 vol /c0t4d0s3 part_off 1044 part_siz 35842616 disaster#sho disk-parti /c0t4d0 Disk size� : 35843670 sectors Partition 1: UNUSED,������� offset�������� Partition 2: CISCO_BFS_1,�� offset������� 10 sectors, size��ï Partition 3: CISCO_CFS_1,�� offset����� 1044 sectors, size� 35842616 sector Partition 4: UNUSED,������� offset�������� El disco duro defectuoso está otra vez conectado. Filesystem Statistics for volume /c0t4d0s3�� Status: mounted ����Data Bytes Max����� 17907227 KB ����Data Bytes Used����������� 0 KB ( 0% fu ����Disk Wraps 0 ����Inode Hits 0 ����Inode Misses 0 ����CFS Read error 0 ����CFS Write error 0 ����Inode Load error 0 ����Attribute Load error 0 ����CFS Object Truncations 0 ����Truncated CFS Object Flushes 0 ����Volume Clears 0 ����Format time�� Fri Mar 24 13:33:21 2000 ����Mount time��� Fri Mar 24 13:33:44 2000 ����Unmount time� Fri Mar 24 13:33:19 2000 Información Relacionada Preguntas frecuentes sobre el motor de memoria caché Notas Técnicas de Troubleshooting © 1992-2016 Cisco Systems Inc. Todos los Derechos Reservados. Fecha de Generación del PDF: 17 Octubre 2016 http://www.cisco.com/cisco/web/support/LA/102/1025/1025004_ce_diskrec.html