ASSEMBLE MANUAL MAGIC GS - 700 The seat slips toward before to move away the screws AN311A with its respective Nuts and Washers of 3/16” that are in the rear part of the seat. Once retired the back screws, the seat is removed slipping it for the rails and then take off the front screws to remove the rails. For then install the legs, working for the openings of it inspected of the floor. First, the pin b u s h i n g i s introduced before introducing the leg www.aircraft-ibis.com [email protected] PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA TELEFAX: (57-2) 5504280 / 6814433 EXT 5 MÓVIL: (57-314) 7925413 / 7926626 When introducing the main train in the fuselage with their respective pin bushing, you also proceeds to introduce the screw AN6-47A, by means of the channel, this screw should cross the channel and in the interior part between the channel of the train and the new leg the complements bushings should be introduced, one to one. MEM - 0001 - P1 Rev. 002 ASSEMBLE MANUAL MAGIC GS - 700 Introduced the Bushings in the leg, we can introduced the leg in the fusselage. complements bushings www.aircraft-ibis.com [email protected] Inside the channel the system should be this way The complements bushings are positioned as the screw pin AN6-47A is introduced Once the screw pin finds crossed the channel this it should be adjusted with its respective nut and washer. PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA TELEFAX: (57-2) 5504280 / 6814433 EXT 5 MÓVIL: (57-314) 7925413 / 7926626 MEM - 0001 - P2 Rev. 002 ASSEMBLE MANUAL MAGIC GS - 700 Already positioned the leg and insured in the channel you proceeds to position the teflon piece between the leg and the channel of the Main Gear. Holding the leg, two Screws AN4-16A is introduced by means of the opening of the floor of where the seats were removed, making sure that the screws pass among the channel, the teflon and the leg. Introduced the 2 Screws AN4-16 makes sure each one with its respective Nut and Washer of 1/4.” Once finished the work you proceeds to carry out the same procedure for the leg of the main gear of the following side. Mounted the two legs and insureds you proceeds to carry out the assembly of the seats placing the rails that were removed and assuring the screws that initially were removed. www.aircraft-ibis.com [email protected] PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA TELEFAX: (57-2) 5504280 / 6814433 EXT 5 MÓVIL: (57-314) 7925413 / 7926626 MEM - 0001 - P3 Rev. 002 ASSEMBLE MANUAL MAGIC GS - 700 Insureds the legs you proceeds to carry out the assembly of the tires and wheel pants. Before Introducing the axis, the complement should be first. Introduced the axis, is positioned in the leg, the plate for wheel pants. Then the axis is assured with its respective nut and its pin. www.aircraft-ibis.com [email protected] later on, the axis is introduced to the leg of the main gear. A Screw AN4-14A is assured with its respective nut and washer between the plate wheels, the leg, and the complement of the axis, for the superior part of the axis PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA TELEFAX: (57-2) 5504280 / 6814433 EXT 5 MÓVIL: (57-314) 7925413 / 7926626 MEM - 0001 - P4 Rev. 002 ASSEMBLE MANUAL MAGIC GS - 700 In the front part of the wheel, be sure that the washer be introduced in the axis. Positioned plate of the wheel pants, it is introduced the respective nut of the axis and insured. www.aircraft-ibis.com [email protected] Positioned the washer, the plate of the wheel pants is introduced in the axis. Then the pin is introduced in the axis. PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA TELEFAX: (57-2) 5504280 / 6814433 EXT 5 MÓVIL: (57-314) 7925413 / 7926626 MEM - 0001 - P5 Rev. 002 ASSEMBLE MANUAL MAGIC GS - 700 Insured the wheel and tested the breake system, the wheel pants of the tires of the Main Gear is positioned. The wheel pants are positioned of up down leaving them on the plates of wheel pants insureds in the leg. www.aircraft-ibis.com [email protected] PLANTA DE PRODUCCIÓN VEREDA PASO DE LA BOLSA KM 2 VÍA LA VENTURA MUNICIPIO DE JAMUNDI-VALLE DEL CAUCA COLOMBIA SUR-AMERICA TELEFAX: (57-2) 5504280 / 6814433 EXT 5 MÓVIL: (57-314) 7925413 / 7926626 Positioned the wheel pants, it is screwed in the front part with 2 screws R-8 and for the rear part of the wheel pants it is screwed with 2 screws R-8. This operation is carried out for the two sides of the Main Gear. MEM - 0001 - P6 Rev. 002