El decodificar del Error de hardware del indicador luminoso

El decodificar del Error de hardware del indicador luminoso LED
amarillo de la placa muestra gravedad menor del Frame Relay PAD
IPX (FRP)
Contenido
Introducción
prerrequisitos
Requisitos
Componentes Utilizados
Convenciones
Errores de hardware FRP de IPX
Información Relacionada
Introducción
Los indicadores luminosos LED amarillo de la placa muestra gravedad menor y los módulos del Cisco WAN Switching registran los códigos de
error cuando ocurre una anomalía. Los errores de placa del switch son indicados al usuario por un símbolo CD en la parte inferior de la pantalla
de la interfaz de línea del comando switch (CLI). Usted puede utilizar el comando dspcderrs de visualizar una lista de errores. Los errores se
presentan sobre la base del nivel de acceso.
prerrequisitos
Requisitos
No hay requisitos específicos para este documento.
Componentes Utilizados
Este documento no tiene restricciones específicas en cuanto a versiones de software y de hardware.
Convenciones
Consulte Convenciones de Consejos Técnicos de Cisco para obtener más información sobre las convenciones sobre documentos.
Errores de hardware FRP de IPX
Esta lista en esta sección es una referencia para los Errores de hardware del indicador luminoso LED amarillo de la placa muestra gravedad
menor del Frame Relay PAD IPX (FRP) presentados hasta el Stratacom-nivel. Los errores en el nivel de StrataCom son servicio-significativos
solamente. Usted puede ser que no vea todos los errores enumerados.
=============================================================================
==== HARDWARE AND SOFTWARE error lists (hw_code.h)
BY MGC (09-30-92)
====
==== Present Revision: 2.0
====
==== Revision History: FDE/FEE + FTC
BY CvH (05-25-94)
====
====
====
Added Self-Test Failures
BY CvH (06-22-94)
====
Corrections
BY CvH (08-18-94)
Add non-ACP errors
BY CvH (08-18-94)
====
====
====
=============================================================================
*** GENERIC FATAL ERRORS ****
Hardware Error Message Format
|Fcn Code (if due to a command, else 0)
| |Error: 1 - download failure
| | |
2 - power-up failure
| | |
3 - selftest failure
| | |
4 - memory test failure
| | |
5 - internal boot failure
| | |
6 - internal ACP failure
| | |
7 - watchdog failure
| | |Slot/Type (Type if MSB set): 99 (19) if FRP, A3 (23) if FTC
| | | |Processor Number
| | | | |
0B01029901 000000ii xxxxxxxx yyyyyyyy : Power-up Failure
i
= failure state
05h - novram checksum failed
06h - fifo loopback failed
07h - no state 0 msg from supv. (SRAM problem)
10h - fifo test failed
11h - no state 1 msg from supv.
>= 12h - passed boot prom (missed handshake)
x = failure address, y = data expected
0B01049901 xxxxxxxx yyyyyyyy zzzzzzzz: Memory Test Failure
x = failure address, y = data expected, z = data received
0B01059901 000000ii : Internal Boot Failure
i = failure mode
0 - waiting for HF flag change from DSP
1 - waiting for TXDE flag to go true from DSP
2 - waiting for RXDF flag to go true from DSP
3 - unable to initialize DSP
4 - unable to internal load DSP
5 - unable to program EEPROM
6 - bad message from CBUS controller
7 - 9th bit/msg format error from supv.
8 - no NMICLR in response to NMI to supv.
9 - timeout waiting for space in Admin fifo
0B00079901 : 8751 Watchdog Timeout
*** FATAL HARDWARE ERRORS **** (The byte count will be 17)
0B00069901 FF 01 00 00 [sr:16][pc addr][vo:16] : acp_stop Error
(@pc addr)
0B00069901 FF 01 00 01 [ pc addr ] [err addr ] : pSOS K_FATAL Error (@pc addr)
error usually a pSOS code: 4B = max. num. cnfg. timers exceeded
*** FATAL ADDRESS/BUS EXCEPTION ERRORS **** (The byte count will be 23)
0B00069901 FF 01 00 00 [sr:16][pc addr][vo:16][ssw:16][fault addr]
*** NON-FATAL HARDWARE ERRORS **** (The byte count will be 13)
0B00069901 01 00 00 C0 [lcn
] : Expect psos message (test frame)
0B00069901 01 00 ii C1 00 00 00 00 : DIAGS test aborted in tm on; i = port
0B00069901 01 00 ii C3 [message
] : Loopback frm not received; i = port
0B00069901 01 00 ii C4 [hchannel ] : Loopback frm bad hch number; i = port
0B00069901 01 00 ii C5 [length
] : Loopback frm bad frame length; i = port
0B00069901 01 00 ii C6 [address
] : Loopback frm incorrect data; i = port
0B00069901 01 00 ii C7 [address
] : Loopback frm zero segment; i = port
0B00069901 01 00 ii C8 [testnum
] : Invalid test number (diags); i = port
0B00069901 01 00 00 C9 [bc type
] : Bad internal card type
0B00069901 01 00 ii C9 00 00 00 00 : DIAGS test aborted in tm off; i = port
0B00069901 01 01 00 80 [response ] : Bad SLOT ID response (startup)
0B00069901 01 01 00 90 00 00 00 00 : Bad watch dog timer event rcvd (cmd_task)
0B00069901 01 01 D0 00 [status
] : FPTX HP failure status during dnld
0B00069901 01 01 D0 01 [status
] : FPTX watchdog HP failure status
0B00069901 01 01 D0 02 [status
] : FPTX activate HP error status
0B00069901 01 01 D0 03 [status
] : FPTX deactivate HP error status
0B00069901 01 01 D0 04 [status
] : FPTX write command HP error status
0B00069901 01 01 D0 05 [status
] : FPTX read command HP error status
0B00069901 01 01 D0 06 [status
] : FPTX self test HP error status
0B00069901 01 01 D0 07 [status
] : FPTX activate: HP status bad
0B00069901 01 01 D0 08 [status
] : FPTX purge: HP status bad
0B00069901 01 01 D0 09 [status
] : FPTX purge all: HP status bad
0B00069901 01 01 D0 0A [status
] : FPTX suspend: HP status bad
0B00069901 01 01 D0 0B [status
] : FPTX resume: HP status bad
0B00069901 01 01 D1 00 [status
] : FPRX HP failure status during dnld
0B00069901 01 01 D1 01 [status
] : FPRX watchdog HP failure status
0B00069901 01 01 D1 02 [status
] : FPRX activate HP error status
0B00069901 01 01 D1 03 [status
] : FPRX deactivate HP error status
0B00069901 01 01 D1 04 [status
] : FPRX write command HP error status
0B00069901 01 01 D1 05 [status
] : FPRX read command HP error status
0B00069901 01 01 D1 06 [status
] : FPRX self test HP error status
0B00069901 01 01 D1 07 [status
] : FPRX cnfig MC HP status
0B00069901 01 01 D1 08 [status
] : FPRX stats bad HP status
[index
] : STATS invalid stats buffer index
0B00069901 01 01 D1 09 [status
] : FPRX LCA boot response bad HP status
0B00069901 01 01 D1 0A [status
] : FPRX suspend cnfig MC HP status
0B00069901 01 01 D1 0B [status
] : FPRX resume cnfig MC HP status
0B00069901 01 01 D2 00 [status
] : DMA HP failure status during dnld
0B00069901 01 01 D2 01 [status
] : DMA watchdog HP failure status
0B00069901 01 01 D2 02 [status
] : DMA activate HP error status
0B00069901 01 01 D2 03 [status
] : DMA deactivate HP error status
0B00069901 01 01 D2 04 [status
] : DMA write command HP error status
0B00069901 01 01 D2 05 [status
] : DMA read command HP error status
0B00069901 01 01 D2 06 [status
] : DMA self test HP error status
0B00069901 01 01 D2 07 [hch/stat ] : DMA HP msg failed @ enable channel
0B00069901 01 01 D2 08 [hch/stat ] : DMA HP msg failed @ disable channel
0B00069901 01 01 D2 0A [status
] : DMA HP msg failed @ inc hp counter
0B00069901 01 01 D2 0B [status
] : DMA HP msg failed @ reset hp counter
0B00069901 01 01 D2 0C [status
] : DMA HP msg failed @ resume receive
0B00069901 01 01 D2 0D [status
] : DMA HP msg failed @ halt receive
0B00069901 01 01 D2 0E [ts/stat
] : DMA HP msg failed @ idle code
0B00069901 01 01 D2 17 [code
] : DMA enable channel msg code incorrect
0B00069901 01 01 D2 18 [code
] : DMA disable channel msg code incorrect
0B00069901 01 01 D2 28 [length
] : DMA disable channel msg len. incorrect
0B00069901 01 02 00 8A [buf index] : FIFO cmd read too long/not end bit set
0B00069901 01 02 00 8C [msg index] : FIFO cmd too long to write out
0B00069901 01 02 00 8D 00 00 00 00 : Exceeded FIFO test wait time
0B00069901 01 02 00 8E 00 00 00 00 : VC Table corrupted (
256 lcns)
0B00069901 01 02 00 8F 00 00 00 00 : Complex GW con received OAM packet
0B00069901 01 02 00 91 [Tmr 1 Cnt] : CIO Timer 1 Errors
0B00069901 01 02 00 92 [Tmr 2 Cnt] : CIO Timer 2 Errors
0B00069901 01 02 00 93 [Tmr 3 Cnt] : CIO Timer 3 Errors
0B00069901 01 02 00 94 [Prt A Cnt] : CIO Port A Errors
0B00069901 01 02 00 95 [Prt B Cnt] : CIO Port B Errors
0B00069901 01 02 ii B0 00 00 00 00 : PRT_CTRL DxE setup failure;
i = port
0B00069901 01 02 ii B1 [baudindex] : PRT_CTRL invalid baud rate;
i = port
0B00069901 01 02 ii B2 [clkselect] : PRT_CTRL invalid clk select;
i = port
0B00069901 01 02 ii B3 [timer cnt] : PRT_CTRL invalid pit count;
i = port
0B00069901 01 02 ii B4 00 00 00 00 : BRSAMPLE invalid cntr value;
i = port
0B00069901 01 02 ii B5 00 00 00 00 : BRSAMPLE invalid timer value; i = port
0B00069901 01 02 ii B6 00 00 00 00 : BRSAMPLE zero elapsed time;
i = port
0B00069901 01 02 ii B8 [eia lead ] : EIA_MON lead failure; i = port
0B00069901 01 02 00 F2 [checksum ] : Bad novram checksum
0B00069901 01 02 00 CA 00 00 00 ii : CAM_CTRL update_lcn_cam, inv. port = i
0B00069901 01 02 01 CA 00 00 00 ii : CAM_CTRL clear_lcn_cam,
inv. port = i
0B00069901 01 02 02 CA 00 00 00 ii : CAM_CTRL cam_lcn_lookup, inv. port = i
0B00069901 D0 00 03 01 [data
] : FPTX watchdog failure data
0B00069901 D0 01 01 00 [length
] : FPTX bad rsp length after dnld (dsp_ctrl)
0B00069901 D0 01 01 01 [length
] : FPTX watchdog response incorrect length
0B00069901 D0 01 01 05 [length
] : FPTX read command incorrect length
0B00069901 D0 01 01 06 [length
] : FPTX self test incorrect length
0B00069901 D0 01 01 09 [length
] : FPTX purge all: incorrect length rtned
0B00069901 D0 01 01 DB 00 00 00 00 : FPTX bootstrap failed
0B00069901 D0 01 02 00 [code
] : FPTX bad code rsp after dnld (dsp_ctrl)
0B00069901 D0 01 02 01 [code
] : FPTX watchdog incorrect fcn. code rtned
0B00069901 D0 01 02 05 [code
] : FPTX read command incorrect msg code
0B00069901 D0 01 02 06 [code
] : FPTX self test incorrect msg code
0B00069901 D0 01 02 09 [code
] : FPTX purge all: incorrect code returned
0B00069901 D0 01 02 DB 00 00 00 00 : FPTX boot failed
0B00069901 D0 01 03 00 [data
] : FPTX bad data rsp after dnld (dsp_ctrl)
0B00069901 D0 01 03 01 [data
] : FPTX watchdog failure data
0B00069901 D0 01 03 06 [status
] : FPTX STSTS self-test error
0B00069901 D1 00 03 01 [data
] : FPRX watchdog failure data
0B00069901 D1 01 01 01 [length
] : FPRX watchdog response incorrect length
0B00069901 D1 01 01 00 [length
] : FPRX bad rsp length after dnld (dsp_ctrl)
0B00069901 D1 01 01 05 [length
] : FPRX read command incorrect length
0B00069901 D1 01 01 06 [length
] : FPRX self test incorrect length
0B00069901 D1 01 01 08 [length
] : FPRX stats response bad length
0B00069901 D1 01 01 09 [length
] : FPRX LCA boot response bad length
0B00069901 D1 01 01 DB 00 00 00 00 : FPRX bootstrap failed
0B00069901 D1 01 02 00 [code
] : FPRX bad code rsp after dnld (dsp_ctrl)
0B00069901 D1 01 02 01 [code
] : FPRX watchdog incorrect fcn code rtned
0B00069901 D1 01 02 05 [code
] : FPRX read command incorrect msg code
0B00069901 D1 01 02 06 [code
] : FPRX self test incorrect msg code
0B00069901 D1 01 02 08 [code
] : FPRX stats response bad code
0B00069901 D1 01 02 09 [code
] : FPRX LCA boot response bad code
0B00069901 D1 01 02 DB 00 00 00 00 : FPRX boot failed
0B00069901 D1 01 03 00 [data
] : FPRX bad data rsp after dnld (dsp_ctrl)
0B00069901 D1 01 03 01 [data
] : FPRX watchdog failure data
0B00069901 D1 01 03 06 [status
] : FPRX STSTS self-test error
0B00069901 D1 01 03 09 [data
] : FPRX LCA boot error response data <> 0
0B00069901 D2 00 03 01 [data
] : DMA watchdog failure data
0B00069901 D2 01 01 00 [length
] : DMA bad rsp length after dnld (dsp_ctrl)
0B00069901 D2 01 01 01 [length
] : DMA watchdog response incorrect length
0B00069901 D2 01 01 05 [length
] : DMA read command incorrect length
0B00069901 D2 01 01 06 [length
] : DMA self test incorrect length
0B00069901 D2 01 01 09 [msg len
] : DMA incorrect msg length
0B00069901 D2 01 01 DB 00 00 00 00 : DMA bootstrap failed
0B00069901 D2 01 02 00 [code
] : DMA bad code rsp after dnld (dsp_ctrl)
0B00069901 D2 01 02 01 [code
] : DMA watchdog incorrect fcn code rtned
0B00069901 D2 01 02 05 [code
] : DMA read command incorrect msg code
0B00069901 D2 01 02 06 [code
] : DMA self test incorrect msg code
0B00069901 D2 01 02 09 [msg code ] : DMA incorrect msg code
0B00069901 D2 01 02 DB 00 00 00 00 : DMA boot failed
0B00069901 D2 01 03 00 [data
] : DMA bad data rsp after dnld (dsp_ctrl)
0B00069901 D2 01 03 01 [data
] : DMA watchdog failure data
0B00069901 D2 01 03 06 [status
] : DMA STSTS self-test error
0B00069901 D2 01 03 09 [msg data ] : DMA incorrect msg
0B00069901 DB 02 01 00 [ISR ptr
] : DSP not ready with TRDY
0B00069901 DB 02 02 00 [ISR ptr
] : DSP not ready with TXDE for bootstrap
0B00069901 DB 02 03 00 [ISR ptr
] : DSP not ready with TRDY for bootstrap
0B00069901 DB 02 11 00 [ISR ptr
] : DSP not ready with TXDE for boot
0B00069901 DB 02 12 00 [ISR ptr
] : DSP not ready for boot dnld
0B00069901 DB 02 13 00 [ISR ptr
] : DSP not ready with TRDY for boot
0B00069901 DB 02 14 00 [ISR ptr
] : DSP not ready with TXDE for boot
0B00069901 DB 02 15 00 [ISR ptr
] : DSP not ready with TRDY for boot
0B00069901 DD 02 02 00 [ISR ptr
] : DSP has not completed previous command
0B00069901 DD 02 03 00 [CVR ptr
] : DSP did not respond to sent command
0B00069901 DD 02 04 00 [ISR ptr
] : DSP did not receive HP bytes
0B00069901 DD 02 05 ii [ISR ptr
] : DSP not ready to receive
0B00069901 DD 02 06 00 [ISR ptr
] : DSP did not ack command reception
0B00069901 DD 02 07 00 [CVR ptr
] : DSP not ready for "execute host" cmd
0B00069901 DD 02 08 00 [ISR ptr
] : DSP did not ack command completion
0B00069901 DD 02 09 00 [ISR ptr
] : DSP did not return HP command response
0B00069901 DD 02 0A 00 [CVR ptr
] : DSP not ready for slave read response
0B00069901 DD 02 0B ii [ISR ptr
] : DSP failed to return RXDF
0B00069901 DD 02 0C 00 [CVR ptr
] : DSP not ready for close output
0B00069901 F0 01 00 03 [llcb_ptr ] : FREE_FRM: Frame Buffer Overflow (> Max FB/Frm)
0B00069901 F1 01 00 03 [frm_ptr
] : FTX_RECY: Frame Buffer Overflow (> Max FB/Frm)
0B00069901 F1 01 00 05 00 00 00 00 : FTX_RECY: Spyder overrun
0B00069901 F1 01 00 06 00 00 00 00 : FTX_RECY: Spyder underrun
0B00069901 F1 01 00 07 [hpr_q_ptr] : FTX_PURG: Bad Hi-priority Q pointer
0B00069901 F1 01 00 08 [lpr_q_ptr] : FTX_PURG: Bad Lo-priority Q pointer
0B00069901 F1 01 00 09 [fim_q_ptr] : FIM_PURG: Bad Fim Q pointer
0B00069901 F1 01 00 0D [dma error] : FTX_RECY: Undefined TX DMA Error
0B00069901 F2 01 00 01 [fcb_tail ] : FRX_RECY: FCB Q overflow [Port only]
0B00069901 F2 01 00 03 [frm_ptr
] : FRX_RECY: Recycled too many frame bufs
0B00069901 F2 01 00 04 [prev_fptr] : FRX_RXFR: SOF rcvd B4 last frame's EOF
[curr_fptr] : FRX_RXFR: (always comes in pairs)
0B00069901 F2 01 00 05 [error
] : FRX_RXFR: Unexpected DMA error code
0B00069901 F2 01 00 06 00 00 00 00 : FRX_RXFR: SPYDER UNDERRUN
0B00069901 F2 01 00 0A [pointer
] : FRX_RXFR: DMA interrupt Q Overrun
0B00069901 F2 01 00 0B [error
] : FRX_RXFR: Undefined RX DMA error
0B00069901 F2 01 00 0C [hyperch
] : FRX_RECY: FB in use underrun (count)
0B00069901 F2 01 00 0E [frm_ptr
] : FRX_IDLE: Zero FB Reported (FRX_DLOK/DLC0/PTLB)
0B00069901 F2 01 00 0F [hyperch
] : FRX_RXFR: Invalid DMA hyperchannel
0B00069901 F2 01 00 10 [pt_rx_ptr] : FRX_RXFR: Invalid DMA offset
0B00069901 F2 01 00 11 [frm_ptr
] : FRX_RXFR: Firmware Frame in Progress Error
0B00069901 F2 01 00 12 [frm_ptr
] : FRX_RXFR: Missing EOF Status
0B00069901 F2 01 00 13 [frm_ptr
] : FRX_RXFR: Sequence Error Status
*** SOFTWARE ERRORS **** (The byte count will be 3)
Guidelines for Error Codes:
0 - unknown function code
1 - illegal length
2 - illegal parameter
3 - unused
4 - illegal for card state
5 - illegal for channel state
6 - configuration error
7 - illegal for backcard state
Error Code
Module
Error Reason
----------
--------
---------------------------------------
02 xx 00
: COMMAND
: Invalid command
*** SPECIAL ***
02 xx 01
: COMMAND
: Invalid message length
*** SPECIAL ***
02 03 03
: CMD_STST : Bad self test number ( != 0 or 1)
02 03 04
: CMD_STST : FRIC not active
02 18 02
: CMD_MEM
: Bad parameter (write_memory_cmd)
02 19 02
: CMD_MEM
: Bad parameter ( read_memory_cmd)
02 1A 04
: CMD_MEM
: Command not supported (memory_test_cmd)
02 1B 02
: CMD_MEM
: Bad parameter (write_NOVRAM_cmd)
02 1C 02
: CMD_MEM
: Bad parameter ( read_NOVRAM_cmd)
02 1D 02
: CMD_LED
: Bad LED bitmap
02 1E 02
: CMD_DBUG : Command not supported (scope_loop_cmd)
02 1F 02
: CMD_DBUG : Invalid processor type (ascii_event_cmd)
02 20 04
: CMD_DNLD : Command not supported (transfer_begin_cmd) [PORT]
02 21 04
: CMD_DNLD : Command not supported (transfer_cmd)
[PORT]
02 22 04
: CMD_DNLD : Command not supported (transfer_end_cmd)
[PORT]
02 A0 02
: CMD_CFBC : Back card type mismatch
02 A0 03
: CMD_CFBC : Bad BC state parameter (BC_RESET)
02 A0 04
: CMD_CFBC : Bad BC state parameter (UNKNOWN)
02 A1 02
: CMD_BCST : Port not configured yet
02 A2 02
: CMD_ALM
: Port not configured yet
02 A2 03
: CMD_ALM
: Back card type mismatch
02 AB 04
: CMD_DCC
: Bad time slot number ( >= MAX_E1_TIMESLOTS)
02 B0 02
: CMD_HCH
: Bad hyperchannel number ( >= MAX_HCHANNELS)
: CMD_PORT : Bad port ( >= Bd_Table.back_card_ports)
02 B0 04
: CMD_HCH
: FRIC not active
02 B0 05
: CMD_HCH
: Unallowd port reconfig (eg Bundled <=
02 B0 06
: CMD_HCH
: Bad timeslot configuration
02 B0 07
: CMD_HCH
: Timeslot number out of range
02 B0 08
: CMD_HCH
: Timeslot already activated/deactivated
02 B0 xx
: CMD_HCH
: Bad back card type (xx = rcvd back card type)
02 B1 02
: CMD_PORT : Bad port ( >= Bd_Table.back_card_ports)
02 B2 02
: CMD_HCST : Bad hyperchannel number ( >= MAX_HCHANNELS)
Unbundled)
: CMD_PTST : Bad port ( >= Bd_Table.back_card_ports)
02 B3 02
: EIA_EVT
: Bad port ( >= Bd_Table.back_card_ports) [PORT]
(get_port_eia_status_cmd)
02 B4 02
: CARD_EVT : local bus param non-zero
02 B7 04
: CMD_ICA
02 B8 02
: CMD_HCCG : Bad hyperchannel number ( >= MAX_HCHANNELS)
: FRIC not active
: CMD_PTCG : Bad port ( >= Bd_Table.back_card_ports)
02 B8 04
: CMD_HCCG : FRIC not active
02 B9 02
: CMD_HCCG : Bad hyperchannel number ( >= MAX_HCHANNELS)
: CMD_PTCG : Bad port ( >= Bd_Table.back_card_ports)
02 BF 02
: CMD_DIAG : Bad port ( >= Bd_Table.back_card_ports) [PORT]
Bad test number ( != 1,2,3) [PORT]
Bad test number to terminate
02 BF 03
: CMD_DIAG : Bad hyperchannel number ( >= MAX_HCHANNELS)
02 BF 04
: CMD_DIAG : Hyperchannel/FRIC not active
02 BF 05
: CMD_DIAG : Bad test number ( != 1, 2, or FF) [LINE]
: CMD_DIAG : Port not active [PORT]
02 BF 06
: CMD_DIAG : Bad test number to terminate
02 BF 07
: CMD_DIAG : FRIC not active
02 C0 02
: CMD_VC
: Bad hyperchannel number, DLCI, LCN
: CMD_VC
: Bad DLCI, port ( >= Bd_Table.back_card_ports)
02 C0 03
: CMD_VC
: Hch/port number doesn't match database for active LC
02 C0 04
: CMD_VC
: FRIC not active
02 C0 05
: CMD_VC
: VC already active (used by multicast) [REMOVE]
02 C0 07
: CMD_VC
: VC already active
02 C0 08
: CMD_VC
: FastPAD not active
02 C1 02
: CMD_VC
: Bad LCN [REMOVE]
02 C1 05
: CMD_VC
: VC already active (used by multicast) [REMOVE]
02 C2 02
: CMD_VCST : Bad LCN [REMOVE]
02 C5 02
: CMD_MC
: Command not supported
02 C6 02
: CMD_MC
: Command not supported
02 C7 02
: CMD_RTD
: Bad LCN [REMOVE]
02 C7 04
: CMD_RTD
: FRIC not active
02 C8 02
: CMD_VCCG : Bad LCN [REMOVE], LCN not active
02 C8 03
: CMD_VCCG : LCN not active
02 C8 04
: CMD_VCCG : FRIC not active
02 C9 02
: CMD_VCCG : Bad LCN [REMOVE]
02 CC 02
: CMD_FPID : FRIC not active [PORT-FTC]
02 CC 03
: CMD_FPID : Bad port ( >= MAX_PORT) [PORT-FTC]
02 CC 04
: CMD_FPID : No match & no space found in Fp_Table [PORT-FTC]
02 CC 05
: CMD_FPID : Bundling on Fp inconsistent with Port [PORT-FTC]
*** SELF-TEST RESPONSES **** (from STSTS)
Code
Meaning
----------
---------------------------------------
03 00
: Done
03 80
: Abort
(Success)
03 01 01 02 00 F0 00 00 00 00 : Fail - invalid FPTX self-test
03 01 01 02 00 F0 00 00 00 01 : Fail - invalid FPRX self-test
03 01 01 02 00 F0 00 00 00 02 : Fail - invalid DMA
self-test
03 01 01 02 00 F2 xx xx yy yy : Fail - self_test_eeprom: x = calc.
checksum,
y = stored checksum @ 83FFFC
03 01 01 02 xx F3 yy yy yy yy : Fail - self_test_routing_table: x =
test,
y = routing table address
03 01 01 02 xx F4 yy yy yy yy : Fail - self_test_gram: x = test,
y = GRAM address
03 01 01 02 00 F5 [data & 30] : Fail - self_test_power_monitor
03 01 D0 01 01 06 [
status ] : Fail - self_test_fptx
03 01 D1 01 01 06 [
status ] : Fail - self_test_fprx
03 01 D2 01 01 06 [
status ] : Fail - self_test_dma
03 01 D2 CA CA ii xx xx yy yy : Fail - self_test_cam [LINE]
i = data pattern, x = lcn, y = CAM lcn
Información Relacionada
Notas Técnicas de Troubleshooting
© 1992-2016 Cisco Systems Inc. Todos los Derechos Reservados.
Fecha de Generación del PDF: 17 Octubre 2016
http://www.cisco.com/cisco/web/support/LA/102/1024/1024647_94.html